-
Bogen PM-3180 - page 1
User ’ s guide ...
-
Bogen PM-3180 - page 2
Models PM-3000 & PM-3180 User ’ s Guide Part No. 54-5003-02 9707 ...
-
Bogen PM-3180 - page 3
© 1996 Bogen Communications, Inc. 50 Spring St., Ramsey , NJ 07446 All rights are reserved. No part of this document may be photocopied, repro- duced, or translated to another language without the prior written consent of Bogen Communications Inc. Notice: The information contained in this document is subject to change with- out notice and should n ...
-
Bogen PM-3180 - page 4
Models PM-3000 & PM-3180 User ’ s Guide Owner ’ s Information Model Number Serial Number_________________________ Date of Purchase______________________ Place of Purchase_____________________ Address______________________________ ____________________________________ iii ...
-
Bogen PM-3180 - page 5
Contents Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Bogen PM-3180 - page 6
1 Unpacking Packing List The ProMatrix carton contains the following components: 1 - ProMatrix unit 1 - Removable Control Panel* 1 - Wireless Infrared Remote Controller 2 - AAA Batteries 1 - 25-foot Control Panel Cable 1 - AC Power Cord 2 - W all Anchors 1 - User Manual 1 - Product Registration Card *The control panel must be connected to the ampli ...
-
Bogen PM-3180 - page 7
Introduction Description The ProMatrix products are designed for sound reinforcement/distribution in multi-room applications. The PM-3180 consists of three independent ampli- fiers, rated at 20, 60 and 100 watts. The PM-3000 is a three channel pre- amplifier unit designed to offer the flexibility for applications with power requirements that exceed ...
-
Bogen PM-3180 - page 8
Introduction Features The ProMatrix units have the following features: • 2 Lo-Z balanced Mic inputs (Mic A is female XLR, Mic B is screw termi- nals). Mic B can be configured as a 600-Ohm transformer balanced input for telephone paging applications. • Automatic level control for Mic inputs. • Choice of microphone precedence activation (VOX, N ...
-
Bogen PM-3180 - page 9
Quick Start This Quick Start section is intended to assist you in getting the ProMatrix unit up and running quickly so that you can become familiar with it. Important: Do not place any objects directly on top of the unit. Leave at least 2 inches of space above the unit to assure prop- er ventilation. When locating the PM-3180, be sure to leave at l ...
-
Bogen PM-3180 - page 10
Quick Start Basic Wiring 1. T emporarily set the AUX INPUT TRIM controls on the rear panel to their full counterclockwise position. T rims will be adjusted later . 2. Be sure that the voltage select switch is set correctly . Connect the power cord to the AC LINE INPUT 3. Connect outputs. For the PM-3000 , connect the correct style output (balanced ...
-
Bogen PM-3180 - page 11
Quick Start Factory Programmed Configuration When the ProMatrix unit is first powered up, the factory default settings are loaded. The factory default priority table is listed below . If you want to change any of these priority levels, you will have to use the ASSIGNMENT function in the programming mode. See the Programming section of these instruc ...
-
Bogen PM-3180 - page 12
Quick Start Basic Operation This section will show you how to: • Apply power to the unit • Understand the Control Panel (See page 12 for full description) • Select which channel the control panel affects • Change volume • Change Bass and T reble response • Manually select an input or allow priority-based switching • Adjust Aux Input T ...
-
Bogen PM-3180 - page 13
Quick Start T o Control V olume Note: Changing any of the volume, bass or treble levels will effect all inputs associated with that amp/channel channel. T urning up the volume for the current amp/channel will cause other inputs assigned to that amp/channel to play louder when they become active. Likewise for bass and treble. Be sure VOL is the curr ...
-
Bogen PM-3180 - page 14
Quick Start T o Select a Specific Input The ProMatrix unit is normally set to monitor input activity and, based on the default or installer-created priority table, automatically switches the proper input for each amp/channel. Y ou can override the priority switching feature of any amp/channel to select a specific input to be on continuously . 1. Pr ...
-
Bogen PM-3180 - page 15
Quick Start Aux Input T rim Adjustment By adjusting the T rim controls as follows, inputs with different signal levels are set approximately equal within the ProMatrix unit. Important: Y ou must properly set the Aux Input Trim Controls. Improperly adjusted trims can result in high distortion levels, poor volume balance between different inputs or f ...
-
Bogen PM-3180 - page 16
Rear Panel Model PM-3000 1. MIC A — Female XLR-type connector for balanced, LO-Z microphone input. Pin 1 is Gnd. 2. MIC B/TEL B — Screw terminal Input for Lo-Z balanced microphone. Software configurable as a 600 Ω transformer coupled paging interface. 3. MIC PREC — Microphone precedence terminals for contact closure activation. 4. AUX INPUT ...
-
Bogen PM-3180 - page 17
12 Rear Panel Model PM-3180 1. MIC A — XLR-type connector for balanced, LO-Z microphone input. Pin 1 is Gnd. 2. MIC B/TEL B — Input for Lo-Z balanced microphone. Software config- urable as a 600 Ω transformer coupled paging interface. 3. MIC PREC — Microphone precedence terminals for contact closure activation. 4. AUX INPUT — Unbalanced i ...
-
Bogen PM-3180 - page 18
Front Panel 1. Alphanumeric display area. 2. AUX A/B/C/D — Input selector buttons & indicators. 3. AUTO — Controls manual or automatic input selection. 4. POWER — Applies power to the ProMatrix unit. 5. AMP 1/2/3 — Amp/Preamp Channel Selector Buttons. 6. Level control Arrow buttons. 7. LED pointer area. 8. PROG, NEXT , BACK, ENT & E ...
-
Bogen PM-3180 - page 19
14 Infrared Remote Controller The infrared remote controller provides all of the functions of the front panel. Before using the controller , install two AAA-size batteries in the battery com- partment of the controller . Be sure to observe correct polarity . T o use the controller , point the controller at the infrared receiver window on the left s ...
-
Bogen PM-3180 - page 20
Wiring Information Outputs For PM-3000 Preamplifier Each preamplifier channel has its own balanced output terminals and unbal- anced RCA output jacks on the rear panel to handle different amplifier and signal processing inputs. 15 1. This figure shows wiring from the PM-3000 Balanced Output to a standard XLR-type of balanced amplifier input. 2. Thi ...
-
Bogen PM-3180 - page 21
Wiring Information Outputs For PM-3180 Amplifier Each amplifier channel has its own output terminal strip on the rear panel. Each terminal strip can handle a different type of speaker load. All amps can handle 70V & 25V distrib- uted or 8- Ω or 4- Ω loads. The 70V , 25V and 8- Ω outputs are transformer-coupled. The 4- Ω output is direct ...
-
Bogen PM-3180 - page 22
Wiring Information AUX Inputs Unbalanced input sources other than microphones are connected to the AUX INPUT jacks. The output lead from the source must be terminated in an RCA-type plug. The input signal range is 100mV rms to 3Vrms and is adjusted using the AUX TRIM controls. Aux Input T rim Controls See page 10 for adjustment procedure Audio Proc ...
-
Bogen PM-3180 - page 23
Wiring Information MIC Inputs Mic A Pin 1 is GND Pin 2 (+) Pin 3 (-) Mic B/T el Program the unit for correct switch precedence or use VOX precedence if no switch closure is available. 1 2 3 If Mic A has a push-to-talk switch, use these termi- nals for the switch connection (see Mic Precedence Setup in the Programming Section). Push-to-talk switch p ...
-
Bogen PM-3180 - page 24
User Operation The ProMatrix Control Panel The control panel is the interface between the user and the unit functions. Since there are three channels (amp or preamp) and only one control panel, the ProMatrix uses selector buttons, indicators and an alphanumeric display to provide control of the overall functions. The information below will famil- i ...
-
Bogen PM-3180 - page 25
User Operation T o Control V olume, Bass or T reble Note: Changing any of the volume, bass or treble levels will effect all inputs associated with that amplifier channel. T urning up the volume for the current amplifier will cause other inputs to play louder when they become active. Likewise for bass and treble. 1. T o control volume, bass, or treb ...
-
Bogen PM-3180 - page 26
User Operation the current input was lowered by . This is because the levels set by the user are temporary and the ProMatrix always strives to maintain volume differences set by the preset programming. T ypically , this will only occur when the inputs or limits are set vastly different for the inputs assigned to an amp channel. The same applies to ...
-
Bogen PM-3180 - page 27
Programming Enter Programming Mode The programming mode lets the installer custom configure the ProMatrix unit. The installer uses the programming buttons on the front panel or the infrared remote controller . Programming Buttons 1. Press PROG. The LED next to the button lights and the display shows 3 dashes. The unit requires a 3-digit password. T ...
-
Bogen PM-3180 - page 28
Programming Programming Menu The ProMatrix programming menu is illustrated below: Press PROG 000 (or user-selected password) Assignment Set priority level for each amplifier-input combination Micr ophone Set precedence activation, ALC, phantom power Preset s Preset volume, bass and treble levels V ol limit Limit maximum volume for each amp-input co ...
-
Bogen PM-3180 - page 29
Programming Assignment The ASSIGNMENT function lets you assign a priority levels to each amplifi- er-input combination. This function lets you create a variety of configura- tion schemes and obtain maximum versatility to meet application needs. The factory default priority levels are listed below: Input Factory Priority Level MIC A 1 MIC B 2 AUX A ...
-
Bogen PM-3180 - page 30
Programming 5. Select a level and press ENT to save the selection (PROG LED will blink when selection has been entered). Important: Y ou must press ENT after every change you make in order to save the new setting. This is true for all program- ming procedures. 6. Repeat Step 3, 4 and 5 to assign any other inputs to the amplifier chan- nel. Note tha ...
-
Bogen PM-3180 - page 31
Programming Mic Set Up This function lets you set the Microphone features: • Precedence Activation: N.O. = Normally Open - requires short between precedence terminals to activate mic N.C. = Normally Closed - requires short between precedence terminals to deactivate mic VOX = V oice Activated switch activation) • Automatic Level Control (ALC) ? ...
-
Bogen PM-3180 - page 32
Programming 4. The display shows A AL C ON indi- cating that MIC A ALC status is ON. 5. Press the NEXT or BACK but- tons to select ON or OFF . 6. Press ENT to store the selection. 7. The display shows A PPS OFF indi- cating that the MIC A phantom power is OFF . If Mic B is set as a TEL input (see below), PPS will not be shown since it does not appl ...
-
Bogen PM-3180 - page 33
Programming Presets This feature lets the installer adjust the power-up volume, bass and treble of each amp/channel-input combination. It also sets the relative volume levels between different inputs on a particular amplifier channel. The same inputs can have different volume and EQ settings on dif ferent amps. Note: The system should be completely ...
-
Bogen PM-3180 - page 34
Programming Note: Press and hold arrow buttons to effect rapid changes in volume. Quick presses of the buttons will effect single-step changes in volume. 5. Once you have set the desired volume for an input, press ENT . The PROG light will blink to indicate that the data was stored. 6. At this point, you can select another amp/channel-input combina ...
-
Bogen PM-3180 - page 35
Programming V olume Limit This function sets the maximum volume level that a user can select for an amp/channel-input combination. W arning: The V olume Limit function will cause the amp- input combination in the PM-3180 to play at the maximum limit (default value is 25, full volume). This will normally be quite loud. Be careful that people are not ...
-
Bogen PM-3180 - page 36
Programming 6. Once you have set the desired limit for an input, press ENT . The PROG light will blink to indicate that data was stored. 7. Select another amp/channel-input combination and repeat Steps 4 and 5 to set other levels. Remember to press ENT after setting each level. 8. Once all levels are set, press EXIT to return to the function menu. ...
-
Bogen PM-3180 - page 37
Programming Inhibit This function lets the installer inhibit the user ’s ability to change the preset volume and tone settings for a particular amplifier (Bass and T reble are always inhibited together as T ones. Pressing BASS or TREB does the same thing). Once set, the unit will not respond to commands from the front panel or remote controller f ...
-
Bogen PM-3180 - page 38
Programming Aux Mute The Aux Mute allows paging over music. This function sets the volume level of each AUX input when a page is made. Upon completion of the page, the music level fades up to the previous level. The levels can be set differently for each Aux input on each amplifier . Note : The system should be completely wired before making any of ...
-
Bogen PM-3180 - page 39
Programming Amplifier Link (PM-3180 Only) This function disconnects the power amplifier input from the preamp pro- cessing circuit and permits the addition of outboard signal processing equip- ment (such as an equalizer or ambient noise response unit) to the Audio Process RCA connectors on the rear of the amplifier chassis. The link is illustrated ...
-
Bogen PM-3180 - page 40
Programming Password This function lets the installer change the program mode password. 1. Enter programming mode and press the NEXT or BACK buttons until P ASSW ORD appears on the display . 2. Press ENT to enter the function. The display shows the the cur- rent 3-digit password (The default is 0 0 0.) The first numeral will be flashing. 3. Press t ...
-
Bogen PM-3180 - page 41
Programming Labels This function lets you modify the names displayed for the current input source during user operation. For example, you can change the name of A UX A to TAPE . 1. Enter programming mode and press the NEXT or BACK buttons until LABEL S appears on the display . 2. Press ENT to enter the function. The display shows A UXA or a pre- vi ...
-
Bogen PM-3180 - page 42
Programming Factory Defaults This function lets you quickly erase all current configuration programming and return the amplifier to its out-of-box configuration. 1. Enter programming mode and press the NEXT or BACK buttons until DEF AUL TS appears on the display . 2 Press ENT to enter the function. The display shows: CLR ALL NO , referring to Clear ...
-
Bogen PM-3180 - page 43
T esting & T roubleshooting T esting Assignment T est: Remove all audio sources from Aux inputs. Connect an active audio source to the lowest priority input for the current amp/channel. Move the active source through the inputs in the order of priority that was previously set. Result: The input source should immediately change as the audio sour ...
-
Bogen PM-3180 - page 44
T esting & T roubleshooting V ol Limit T est: Manually select an Aux or Mic input. Press and hold the right arrow button until the display stops incrementing. Result: The display stops incrementing at the volume limit for the particular input and amp combination (see page 30). T urn the Promatrix power off and then on to return volume levels to ...
-
Bogen PM-3180 - page 45
T esting & T roubleshooting Mic never active • Check that the type of precedence setting is correct for the application (See page 26). • If mic is a condenser type, check that phantom power is applied to mic input (see page 27) • Check that mic is assigned to the amp in question (see page 24). • If Mic B is the problem, check that it is ...
-
Bogen PM-3180 - page 46
Getting Help Bogen has support available in case you have a problem with your ProMatrix. In order to make the most effective use of this service, please be sure to fill out and return the product registration card included with this unit. Best results are obtained when you: • Read the User’s Guide before operating • Remember that certain func ...
-
Bogen PM-3180 - page 47
Specifications PM-3180 Power Output: Amp 1: 100 wrms Amp 2: 60 wrms Amp 3: 20 wrms Output T aps: 8-ohms, 25V and 70V transformer-coupled (balanced or unbalanced) 4-ohms direct coupled (unbalanced) Output Regulation: <2dB from no load to full load (all amps) Input Sensitivities: Mic Inputs: 750 µ V rms (no ALC) Aux Input: 100mV rms to 2.5Vrms (t ...
-
Bogen PM-3180 - page 48
Specifications PM-3000 Outputs: 0dBV balanced outputs via screw terminal strips (all channels) 0dBV unbalanced outputs via RCA jacks (all channels) Maximum Output: 15dBV into 600 Ω balanced Maximum Gain: 17.7dB (V ol. control @ 25) Input Sensitivities: Mic Inputs: 750 µ V rms (no ALC); T el Input: 170mVrms; Aux Input:100mV rms to 2.5Vrms Input I ...
-
Bogen PM-3180 - page 49
50 Spring Street • Ramsey , NJ 07446 www .bogen.com ...
Bogen PM-3180についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもBogen PM-3180の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBogen PM-3180で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。