Holley 12-150の取扱説明書

6ページ 0.39 mb
ダウンロード

ページに移動 of 6

Summary
  • Holley 12-150 - page 1

    HP FUEL PUMPS P/N 12-125 and 12-150 Installation Instructions WARNING! THESE INSTRUCTIONS MUST BE REA D AND FULLY UNDERST OOD BEFORE BEGINNING INSTA LLATION. FA ILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN POOR PERFO RMANCE, VEHICLE DA MAGE, PERSONA L INJURY, OR DEAT H. IF THESE INSTRUCTIONS ARE NOT FULLY UNDERST OOD, INSTA LLATION SHOULD NOT B ...

  • Holley 12-150 - page 2

    4. Connect the fuel line from the tank to the fuel filter and then to the inlet port of the pump . Connect the carburetor delivery line to the outlet port of the pump and to the regulator (for the 12-150) located near the carburetor inlet. See Figure 1. The fuel pump inlet and outlet ports take a 3/8” NPT fitting, therefore a 3/ 8” or larger fu ...

  • Holley 12-150 - page 3

    WIRING: There are 2 methods to wire the pump: (1) To wire the fuel pump with a relay (2) To w ire the fuel pump with an oil pressure s afety switch. (1) WIRING THE FUEL PUMP WITH A RELAY: NOTE: You will need Holley Fuel pump relay kit P/N 12-753 or equiv alent 4-w ire relay. 1. Disconnect the cables from the battery. 2. Mount relay on firewall of e ...

  • Holley 12-150 - page 4

    Figure 3 6. Connect the fuel pump (red lead) to the terminal marked “C”. In this line, add an in-line fuse holder and a 15-amp fuse. 7. Connect the terminal marked “NO” to t he on terminal of the ignition switch. 8. Connect the terminal marked “NC” to the starte r terminal that’s hot ( 12V) during cranking only. 9. To complete the ins ...

  • Holley 12-150 - page 5

    Figure 4 4. Turn the pump upside down, remove the three bolts, and care fully lift off the pump cover followed by the gasket, pump plate, and O-Ring. 5. Very carefully remove the gerotor assembly (both parts) from the pump housing. WARNING! KEEP THE GEROTO R TOGETHER AS A MATCHED SET. TH IS A SSEMBLY MUST BE REASSEMBLED THE SA ME WAY IT WAS DISA SS ...

  • Holley 12-150 - page 6

    CLEANING THE REGULATOR: Figure 5 1. Loosen the hex nut on the top of the regulator and back the adjusting screw out all the way to relieve tension on the diaphragm spring. See Figure 5. 2. Remove the four screws holding the regulator cover on. The diaphragm and spring will fall out. 3. Use a spray-type carburetor cleaner to clean the cover and regu ...

メーカー Holley カテゴリー Automobile Parts

Holley 12-150のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 12-150の取扱説明書
- Holleyの製品カード
- パンフレット
- またはHolley 12-150の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Holley 12-150の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Holley 12-150の取り付け説明書、サービスマニュアル、簡易説明書、またはHolley 12-150のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Holley 12-150の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Holley 12-150デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHolley 12-150を使用するのを助ける技術的文書のことです。説明書は通常、全てのHolley 12-150ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Holleyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Holley 12-150の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHolley 12-150の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Holley 12-150に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Holley 12-150デバイスの基本機能を使うにあたってのヒント。 Holley 12-150のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Holley 12-150に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHolley 12-150のメーカー/サービスへの連絡先に関する情報。

Holley 12-150についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHolley 12-150の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHolley 12-150で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)