-
Audiovox FR-1438-2 - page 1
Model FR-1438-2 Owner ’s Manual F FR1438-2 ...
-
Audiovox FR-1438-2 - page 2
2 1. Battery Door 2. Monitor Button 3. Detachable Belt Clip 4. Push-T o-T alk (PTT) Button 5. Antenna 6. External Speaker Jack 7. Built-in Speaker 8. Liquid Crystal Display (LCD) 9. Built-in Microphone 10. Up Button and V olume Control 1 1. Down Button and V olume Control 12. Function Button 13. Power On/Off and ENTER Button F FR1438-2 M PTT 3 11 2 ...
-
Audiovox FR-1438-2 - page 3
Model FR1438-2 DISPLA Y 1. RSSI Indicator: Receive signal strength indicator . 2. TX: Icon blinks during transmission. 3. Monitor Indicator: Icon appears when the monitor button is pressed. 4. Coded T one Controlled Squelch System (CTCSS) Indicator: Icon appears when receiving a transmission with correct CTCSS tone. 5. Auto Scan Indicator: Icon app ...
-
Audiovox FR-1438-2 - page 4
4 CH Channel select mode (1-14) ctc Coded T one Controlled Squelch System Sub-Channel Select Mode SC Auto Channel Scan Mode d Dual Channel W atch Mode UO V oice Activated Function Udt V oice Activated Recovery Time ALO Auto Key Lock Selection Mode CAL Call Ringer Melody Selection Mode ton Sub-Channel Number or Sub-Channel Frequency 15. Small Segmen ...
-
Audiovox FR-1438-2 - page 5
1. Press the spring clip and slide the belt clip upwards. 2. Slide the battery cover downward. 3 . Insert batteries observing the polarity symbols on the bottom of the tray . 5 The following guidelines will improve performance and provide longer operating times for the FR1438-2: 1. Do not mix old and new batteries. 2. The use of alkaline-type batte ...
-
Audiovox FR-1438-2 - page 6
Charging the FR1438-2: Insert the charging transformer into a household electrical outlet and connect its power jack to the socket on the rear of the charging stand. Simply placing the unit into the charging stand will begin the charging process. The red LED on the front of the charging transformer serves as a charge indicator . The charging stand ...
-
Audiovox FR-1438-2 - page 7
7 Push T o T alk (PTT) Button (4): Pressing and holding this button will allow you to speak to any transceiver that is set to the same channel and privacy code setting as yours. Hold the transceiver approximately 1 to 2 inches from your face as you speak into the built in microphone (9). After you have finished speaking, release the PTT button to a ...
-
Audiovox FR-1438-2 - page 8
Function Button (12): In the standby mode, pressing this button briefly will enter the function edit mode. Pressing the button for more than 1.5 seconds will activate or deactivate the KEY LOCK when the unit is in the standby mode. Refer to KEY LOCK function description to activate and deactivate the KEY LOCK. NOTE: All buttons will be disabled exc ...
-
Audiovox FR-1438-2 - page 9
9 NOTE: T o communicate with other units, they must be switched to the same channel and CTCSS subcode. T o communicate with other units that do not have subcodes, switch your unit to the same channel with the subcode set to Off. AUTO CHANNEL SCAN MODE: This feature allows scanning for an active channel. The volume cannot be adjusted and the power s ...
-
Audiovox FR-1438-2 - page 10
T o turn off the dual watch feature in the standby mode, simply press the Function Button (12) once. VOX SELECTION MODE The V oice Activated T ransmission (VOX) function allows your voice to activate signal transmission automatically when the FR1438-2 is used with a hands free microphone/ headset (FRS-BHST). It also allows hands free use when a mic ...
-
Audiovox FR-1438-2 - page 11
11 2. Press the Up Button (10) or Down Button (1 1) to select the Auto option. 3. Press the ENTER key to confirm your selection. If you do not press any key for more than 15 seconds in the standby mode, keys will automatically be locked except the PTT (4) and monitor (2) buttons. T o turn the auto key lock on or off in standby mode, simply press an ...
-
Audiovox FR-1438-2 - page 12
W arning • Remove the batteries from the transceiver if it is not expected to be used for long periods. This will eliminate the possibility of chemicals leaking from the batteries and corroding the transceiver . • Avoid exposing the transceiver to water or extremes of temperature. • Do not use this device in or near a mining facility , which ...
-
Audiovox FR-1438-2 - page 13
13 Problem Possible cause Correction No transmission Weak batteries Charge or replace batteries while pressing Incorrect battery Polarity Install the batteries in the the PTT button directions indicated by the battery tray . Weak or no Weak batteries Charge or replace batteries signal received Channel and privacy Adjust the transceiver ’s code no ...
-
Audiovox FR-1438-2 - page 14
T ec hnical Specifica tions: General Frequency Range 462.5625 - 467.7125 MHz Channels 14 Privacy Codes 38 for each main channel Channel Spacing 12.5 kHz Dimensions (W x H x D) 50.6mm x 95.5mm x 26.0mm P ower Supply Power Source Alkaline Batteries, AAA (4), 6 VDC NiMH rechargeable, AAA (4), 4.8 VDC Operating T ime (Tx: Rx: Stdby) About 36 hours (5: ...
-
Audiovox FR-1438-2 - page 15
Continuous T one Coded Squelch System T one Frequencies (in Hz) CTCSS Freq. Hz CTCSS Freq. Hz 1 67.0 20 131.8 2 71.9 21 136.5 3 74.4 22 141.3 4 77.0 23 146.2 5 79.7 24 151.4 6 82.5 25 156.7 7 85.4 26 162.2 8 88.5 27 167.9 9 91.5 28 173.8 10 94.8 29 179.9 1 1 97.4 30 186.2 12 100.0 31 192.8 13 103.5 32 203.5 14 107.2 33 210.7 15 1 10.9 34 218.1 16 1 ...
-
Audiovox FR-1438-2 - page 16
© 2000 Audiovox Corporation, Hauppauge, N.Y. 11788 128-5728A Applies to Audiovox Family Radio Service Products. AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days fro ...
Audiovox FR-1438-2についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもAudiovox FR-1438-2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAudiovox FR-1438-2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。