Unitech PT600の取扱説明書

31ページ 0.36 mb
ダウンロード

ページに移動 of 31

Summary
  • Unitech PT600 - page 1

    USER’S GUIDE PORTABLE DATA COLLECTION TERMINAL PT600 DOCUMENT NUMBER: 350600 - 0010 ...

  • Unitech PT600 - page 2

    NOTICE The unit is equipped with a NiMH battery pack, however it may not be powered on due to discharging of the battery by putting in storage for a period of time. In the case of above situation happened, plug in an 9V A C - DC adapter and recharge the NiMH battery pack about 14~16 hours or put into cradle about 2.5 hours with 12V AC - DC adapter ...

  • Unitech PT600 - page 3

    Table of Content Page Chapter 1 Introduction .......................................... 1 1.1 Technical Specification ................................ 2 1.2 Interface Ports ............................................. 8 1.3 Using the Keyboard ..................................... 9 1.4 Triggering Scanner Module .......................... 11 1.5 Ap ...

  • Unitech PT600 - page 4

    - 1 - Ch apter 1 Introduction The PT600 Portable Data Terminal, referred as PDT hereafter, with integrated laser scanner or pen scanner is a rugged , compact and lightweight hand - held data collection terminal with good reliability, flexibility an d maintainability. Its compact size and form makes it even fits in your packet. The PDT incorporates ...

  • Unitech PT600 - page 5

    - 2 - 1.1 Technical Specification SOFTWARE PROGRAMMING TOOLS Language Assembly, C language (MS C, Turbo C, Visual C) JobGen Plus A Windows - based transaction program generator JobGen Pro A Dos - based transaction program generator FormCaching A built - in program generator CPU/MEMORY CPU 16 - bit 8088 compatible microprocessor CPU Memory 512KB to ...

  • Unitech PT600 - page 6

    - 3 - COMMUNICATION In terface One EIA RS232C with miniature DIN - 9p male connector, Support TX/RX, CTS/RTS, GND, up to 57.6Kbps (default value is 19.2 Kbps ) One IR port, Support TX/RX, from 19.2 to 57.6 K bps Handshaking Xon/Xoff or CTS/RTS Protocol None or Multi - protocol Fil e Transfer Build - in Kermit server or Multi - protocol POWER SUPPLY ...

  • Unitech PT600 - page 7

    - 4 - • Built - in power - on self test and diagnostic program • Host command remote contro l Integrated Laser Diode Scanner • Scan rate 36 scans/sec • Skew Tolerance ± 65 ° from normal • Pitch Angle ± 55 ° of normal • Power consumption 60mA typ.@5V Integrated clip - on P en Scanner • Res o l u tion 0.12mm(5mil) • Dept of field ...

  • Unitech PT600 - page 8

    - 5 - Depth of Field diagram ...

  • Unitech PT600 - page 9

    - 6 - ...

  • Unitech PT600 - page 10

    - 7 - Diagram shown with a clip - on pen scanner 45° 45° ...

  • Unitech PT600 - page 11

    - 8 - 1.2 Interface Ports The PT600 has a RS232C serial port with miniature RJ10 connector, Communication by Infrared LED which on the left side of lower cabinet and charging pads locate on the bottom. Pin Signal Direction Description 1 DC9 V Input External power input 2 TXD Output Transmit date 3 RXD Input Receive date 4 N.C. 5 GND Reference Groun ...

  • Unitech PT600 - page 12

    - 9 - 1.3 Using the Keyboard The keypad of PT600 consists of 27 rubber keys, the   key is used to switch on/off the unit and other 26 keys are used to control the unit and key in data. The use o f keyboard is categorized to th ree modes: normal mode , command mode , and alpha(betic) mode . All keys except   key may produce a sound (tone ...

  • Unitech PT600 - page 13

    - 10 - NORMAL mode Keyboard of the PT600 is initialized to normal mode after powered on. In normal mode, the cursor is a block sign and the keyboard is mainly used to i nput numeric data and use F1 - F4 four function - keys. The keypad layout of available keys in normal mode is shown on right picture.   key for next data search   key fo ...

  • Unitech PT600 - page 14

    - 11 - ALPHA mode Press [ALPHA] key to toggle between normal mode and alpha mode of keyboard. In alpha mode, the cursor is an underscore sign and the keyboard is available to i nput upper case letters. In alpha mode, every numeric key contains 3 characters individually. Pressing the key [ è ] and [ ç ] to choose among three available characters. ...

  • Unitech PT600 - page 15

    - 12 - 1.5 Application Development Environment The system of PT600 provides DOS functions and device drivers for application development, including bar code decoding, keypad input, display output, serial input/output communication, real - time - clock access a nd power management control. The PT600 can be programmed by the high - level Windows - ba ...

  • Unitech PT600 - page 16

    - 13 - 1.6 Optional Charging/Communication Cradle An optional charging/communication cradle (dock ing station), PT016, gives users a convenient accessory for daily use of the PT600. The cradle has been incorporated a quick charge circuit that th e NiMH battery pack installed in the unit along with an extra spare pack can be fully charged in about 2 ...

  • Unitech PT600 - page 17

    - 14 - Chapter 2 Power System 2.1 Power Supply Main Power The PDT is operated by a rechargeable NiMH battery pack with two AA size 1.2V 1500mAH capacity or two AA alkaline batteries for the main power source. Back up Power An onboard 3V 190mAH Lithium battery (CR2032) is used as the secondary power source to back up the data in RTC ( real time cloc ...

  • Unitech PT600 - page 18

    - 15 - When the main battery low condition occurs, the main battery can continue to supply power for about 10 ~ 30 minutes, however the unit may reach the system power cutoff point and automatically turn itself off. Meanwhile the unit continues to back - up the data contents in RTC and RAM, but it cannot be powered up until the batteries have been ...

  • Unitech PT600 - page 19

    - 16 - Remove battery pack Remove backup battery Lithium Back up Battery 1. Refer to the procedure in previous paragraph, un - screw the backup battery cover and as illustration above to remove the lithium ba ttery. 2. Insert a new battery into the holder with correct orientation. 3. Put the battery cover back. * * Make sure to back up your data in ...

  • Unitech PT600 - page 20

    - 17 - 2.4 Recharging the Battery Pack When the PDT sh ows “Main battery low” message or sign , the battery pack in PDT needs to be recharged. There are two ways to charge the battery: regular and quick charging as shown below. AC to 9V DC Transformer Outer shell Inner shell Positive(+) Negative(-) Regular Charging Plug one end of an AC - 9VDC ...

  • Unitech PT600 - page 21

    - 18 - Charging Considerations It is important to consider the surrounding temperature whenever you are cha rging the NiMH battery pack. The process is most efficient at normal room temperature or slightly cooler. It is essential that you charge batteries within the stated range of 32 ° F to 113 ° F (0 ° C to 45 ° C). Charging batteries outside ...

  • Unitech PT600 - page 22

    - 19 - Chapter 3 Operation The system of PDT may op erate in various modes for different purposes. The figure below shows the operating flow of the PDT. press press press and hold down enter program then press press and keys CMD EXIT ENTER CMD <− <− then press PWR PWR name (for two press 2 press 1 seconds) OFF SUPERVISOR mode 1.SUPERVISOR ...

  • Unitech PT600 - page 23

    - 20 - The first line indicates the model code and ve rsion number (e.g. V1.00). The second line shows the size of the total installed RAM (i.e. 4608 KB). The third line prompts a ">" which indicates that the terminal passed the Power - on - test and is ready to be used. 3.2 User Mode and System Commands Ther e are eight system command ...

  • Unitech PT600 - page 24

    - 21 - from a Host computer. In this mode, data input from bar code reader or keyboard is displayed on screen and output to RS - 232 port. Data received from the seria l port is displayed on the LCD screen. Communication parameters, such as baud rate, data bits, parity, stop bits and flow control, must be set to be compatible with the destination i ...

  • Unitech PT600 - page 25

    - 22 - TYP This command dumps the content of a file on the PDT' s LCD. The content of the file will be displayed 128 (16 character x 8 line) characters at a time. Press any key to show the next page or hit [CMD] then [ALPHA ] keys to return to User mode prompt . If you try to display a program or binary file, you may onl y see unintelligible c ...

  • Unitech PT600 - page 26

    - 23 - 1. DATE & TIME: set system clock/calendar When selects “ 1.DATE & TIME ” in SET command menu , the screen as right will be sh own on PDT’s LCD and let you set the system date and time of Real Time Clock chip (RTC). The system date and time can be retrieved in application and used as time stamp for data collection. The second li ...

  • Unitech PT600 - page 27

    - 24 - 3.4 Upload/Download by ESC Command The way to make file upload/download by Kermit server described in section 3.2 will need the operator to set the PDT to Kermit server mode by invoking user comman d “3.COM” in User mode or calling system function in application program. The hardware and software of PDT is designed that the unit can be w ...

  • Unitech PT600 - page 28

    - 25 - Chapter 4 Built - in Application: FormCaching The system of PDT includes a built - in application, FormCaching, that allows user to create a data entry application by specifying field prompt, type, length, input method and delimiter,...,etc. without writing program and loading to the terminal. 4.1 Specification of FormCaching DATA FIEL D DEF ...

  • Unitech PT600 - page 29

    - 26 - 4.2 How to Create a FormCaching You will need to enter Supervisor mode and select “4.FORM” category in order to set the configuration of FormCaching (refer to the PT600 Programming Reference Manual for how to enter the Supervisor mode). After selecting the “4.FORM” in Supervisor mode, the screen will show as above. The syste m will f ...

  • Unitech PT600 - page 30

    - 27 - After collecting data, the FORM.DAT file can be uploaded to host either by invoking kermit server in User mode described in section 3.2 or remote ESC command described in 3.4. 4.4 Default Setting of FormCaching In default, the FormCaching is initialized with settings as shown in the table below. DATA FIELD SPECIFICATION: field number=2 Categ ...

  • Unitech PT600 - page 31

    - 28 - Warning This is a Class A product in a domestic environment this produc t may cause radio interference in which case the user may be required to take adequate measures. ...

メーカー Unitech カテゴリー Stereo System

Unitech PT600のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PT600の取扱説明書
- Unitechの製品カード
- パンフレット
- またはUnitech PT600の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Unitech PT600の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Unitech PT600の取り付け説明書、サービスマニュアル、簡易説明書、またはUnitech PT600のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Unitech PT600の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Unitech PT600デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがUnitech PT600を使用するのを助ける技術的文書のことです。説明書は通常、全てのUnitech PT600ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Unitechの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Unitech PT600の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははUnitech PT600の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Unitech PT600に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Unitech PT600デバイスの基本機能を使うにあたってのヒント。 Unitech PT600のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Unitech PT600に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるUnitech PT600のメーカー/サービスへの連絡先に関する情報。

Unitech PT600についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもUnitech PT600の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがUnitech PT600で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)