-
Locke GT-122 - page 1
Golf and T urf Series GT -126 and GT -122 Operator ’ s Manual 307 Highway 52E, Opp, Alab ama, 36467, (334) 493-1300 Locke T urf ...
-
Locke GT-122 - page 2
CONGRA TULA TIONS Y ou have invested in the best implemen t of its type on the market today . The care you give your Locke T urf implement will greatly determine your satisfaction with it s performance and it s service life. W e urge a careful study of this manual to provide you with a thorough understanding of you new implement before operating, a ...
-
Locke GT-122 - page 3
SECTION Introduction …………………………....2 Warranty ………………………………...3 Safety Important Safety Information …………..4 Training …………………………………..4 Preparation ……………………………....4 Operation ………………………………...4 Maintenance and Storage …………? ...
-
Locke GT-122 - page 4
INTRODUCTION More than merely devices created for mowing gr ass, the excelle nce of design, construction and op- eration of Locke power mowers is unp aralleled. First introduced in 1928, tested and proven, Locke power mowers may be considered, in terms of today ’s technology, the ultimate re sponse to the need for the highest degree of quality la ...
-
Locke GT-122 - page 5
LOCKE MOWER 2 Y ear Limited W arranty WARRANTY PERIOD AND COVERAGE A. Locke Turf, Inc. warrants to the origin al purchaser, and to subsequent owners, that the registered Locke Mower will be free from defects in material s an d workmanship for a perio d of one (1) year from the date of purchase by the original owner. B. Locke Turf, Inc. will, at its ...
-
Locke GT-122 - page 6
IMPORTANT SAFETY INFORMATIO N This Safety Alert Symbol means: ATTENTION! BECOME A LERT! YOUR SAFETY IS INVOLVED! The Safety Alert Symbol identifies important safety mes- sages in manuals and on equipment safet y signs. To avoid possible injury or deat h, follow the equipment and manual’s safety instructions. In addition to the design and configur ...
-
Locke GT-122 - page 7
The space between the bottom of the bed knife (a) is slightly gr eater than that of the front edge (b) by 2 - 3 degrees. See diagram above. HEIGHT OF CUT ADJUSTME NTS The GT Series is engineered and d esi gned to offer the most accurate adjustme nts to produce pristine cutting. An Accu-Gauge is reco mmended to measure the settings. A two point gaug ...
-
Locke GT-122 - page 8
STARTING THE ENGINE Check to see that the oil in the crankcase is at the proper level and th ere is fuel in the t ank. Make sure that the tractor clutch leve r, on the right handlebar, and the reel clutch lever, on the left handlebar, ar e released before attempting to start the engine. Set the engine kill switch to the on position, mo ve the throt ...
-
Locke GT-122 - page 9
LUBRICATION There are 4 pressure lubrication po ints on the mower. All are zerk type grease fittings. Use a qualit y light grease at these points. T he bronze clutch collars each have a grease fitting. These ar e located at the front of the tractor on the left and right sides underneath the main guard. Lubricate with 1 or 2 shots of grease ev er y ...
-
Locke GT-122 - page 10
REEL BEDKNIFE Whenever the bedknife is rep lac ed it is essential that the reel and blade be ground or lapped to alignment. REEL TO BEDKNIFE ADJUST MENT The cutting reel is mounted on sea led ball bearings. These bearings are carried i n brackets hinged to the reel side plates. The hinged brackets ha ve springs which urge the reel blades to ward th ...
-
Locke GT-122 - page 11
RESHARPENING REELS For maximum performance and to achieve the finest cut, reels should be reground wit h a relief. For best results, the “land” area sho uld be no wider than 1/64” to begin the se ason. (See figure below) Modern reel grin ders are capable of pro - ducing a relief, finishing off the cylinder with a light spin grind. RESHARPENIN ...
-
Locke GT-122 - page 12
Locke T urf 307 Highway 52E, Opp, Alab ama, 36467, (334) 493-1300 ...
Locke GT-122についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもLocke GT-122の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLocke GT-122で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。