KTI Networks 2028の取扱説明書

21ページ 0.08 mb
ダウンロード

ページに移動 of 21

Summary
  • KTI Networks 2028 - page 1

    Installation Guide KTI 10/100 Fast Ethernet Switch KS2028 P/N:750-0087-001 DOC.971005-KS2028-K ...

  • KTI Networks 2028 - page 2

    Ó 1997 KTI Networks Inc. All rights reserved. No part of this docu- mentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time t ...

  • KTI Networks 2028 - page 3

    10/100 Fast Ethernet Switch Installation Guide DOC.971006-KS2028-NK P/N: 750-0087-002 ...

  • KTI Networks 2028 - page 4

    The information contained in this document is subject to change without prior notice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are des ...

  • KTI Networks 2028 - page 5

    Table of Contents 1. Introduction ............................................................................... 1 1.1 Features .................................................................................................................. 2 1.2 Specifications ..................................................................................... ...

  • KTI Networks 2028 - page 6

    1. Introduction Driven by recent advances in desktop computing technology, today’s network applications have grown speed, power and the ability to pro- cess information. To meet the demands of these more powerful applica- tions, the switch has been developed to alleviate congestion and im- prove performance on your Ethernet network. The switch co ...

  • KTI Networks 2028 - page 7

    1.1 Features Designed for resolving congestion problems caused by bandwidth-hun- gry devices and bandwidth-intensive applications as well as a high num- ber of users, the switch not only adheres to the IEEE 802.3 10BASE-T and 100BASE-T standard, but also features: • Various TP ports for flexible connection to servers and hubs. - eight 10BASE-T po ...

  • KTI Networks 2028 - page 8

    1.2 Specifications Network ports 10BASE-T ports 8 10/100BASE-TX port 1 Expansion port slot 1 Filtering rate 10BASE-T ports 14,880 pps 10/100BASE-TX port 148,800 pps Expansion port slot 148,800 pps Forwarding rate 10BASE-T ports 14,880 pps 10/100BASE-TX port 148,800 pps Expansion port slot 148,800 pps Filtering address Multicast address unlimited Br ...

  • KTI Networks 2028 - page 9

    2. Installing the Switch The switch is designed to operate in workgroup environments without a complicated configuration procedure. It also features an auto-select 100- 240V, 50/60Hz power supply unit, which works in most countries around the world. Before connecting the supplied power cord into the switch, check to see that the cord voltage and cu ...

  • KTI Networks 2028 - page 10

    Rack Mounting For mounting the switch into a 19-inch rack, a pair of mount brackets is included in the pack. Figure 2-2 Install Rack Mount Brackets Install the switch into a 19-inch rack as illustrated in the following fig- ure: Figure 2-3 Install the Switch into the 19-inch Rack 5 ...

  • KTI Networks 2028 - page 11

    2.3 Front Panel and Rear Panel Figure 2-4 Components on the Front and Rear Panel • Eight 10BASE-T switched ports (Port #1 to Port #8) Each port consists of an RJ-45 connector and is used for connec- tion to a 10BASE-T hub or node. • One 10/100BASE-TX switched port (Port #9) The port consists of an RJ-45 connector and is used for connection to a ...

  • KTI Networks 2028 - page 12

    • Diagnostic LED indicators The indicators provide the operating status of the hub and the network ports. The status includes power, partition, duplex, activity, and collision. • Configuration switches Two configuration switch groups are located on the rear of the switch unit. The switches are used for configuring the operation settings for all ...

  • KTI Networks 2028 - page 13

    Figure 2-6 100BASE-FX Port Module Before installing any optional modules, first turn the power to the switch off. To install a module into the expansion port slot, follow these steps: 1. Turn off the power switch. 2. Remove the cover of the slot. Figure 2-7 Remove the Slot Cover 3. Align the connector and insert the module until it is fully seated. ...

  • KTI Networks 2028 - page 14

    2.5 Setting the Configuration Switches Open the configuration switch cover on the rear of the unit. There are two switch groups as illustrated below: Figure 2-9 Configuration Switches The following table specifies the definition of each switch: The M switch only functions for Port #9 and Port #10. Since Port #1 to Port #8 are fixed 10BASE-T ports, ...

  • KTI Networks 2028 - page 15

    When a operation mode is accepted by the remote device, the mode is used for the data transfer between the port and the connected device. Full-duplex opera- tion enables two devices to transfer data bi-directionally at the same time. For connecting to a hub , refer to the following table for the switch setting: Port Connecting to Setting Port #1 - ...

  • KTI Networks 2028 - page 16

    3. Making Network Connections 3.1 Network Switched Ports There are ten ports on the switch for connection to ten LAN segments. Each segment is an independent shared network in one collision-do- main. Figure 3-1 Network Ports Port #1 to Port #8 are 10Mbps-based 10BASE-T switched ports and dedicated for connecting to eight separate 10Mbps Ethernet se ...

  • KTI Networks 2028 - page 17

    3.2 10BASE-T Switched Ports The individual RJ-45 connectors of Port #1 to Port #7 are defined as X type connectors and have fixed pin assignments as follows: The following table lists the devices to which Port #1 to #7 can connect : Device connected Cable used Computer 10BASE-T port Cat. 3, 5 straight UTP 10BASE-T hub port (I type) Cat. 3, 5 straig ...

  • KTI Networks 2028 - page 18

    The following table lists the devices to which Port #8 can connect : Device connected Crossover SW Cable used Computer 10BASE-T port X setting Cat. 3, 5 straight UTP 10BASE-T hub port (I type) X setting Cat. 3, 5 straight UTP 10BASE-T hub port (X type) I setting Cat. 3, 5 straight UTP 10BASE-T switched port (I type) X setting Cat. 3, 5 straight UTP ...

  • KTI Networks 2028 - page 19

    3.3 10/100BASE-TX Switched Ports This section applies to the 10/100BASE-TX Port #9 and expansion slot Port #10 pre-configured with a 10/100BASE-TX port module. Use the crossover switch to set the type of RJ-45 connector as follows: The following table lists the devices to which the ports can connect: Device connected Crossover SW Cable used Compute ...

  • KTI Networks 2028 - page 20

    3.4 100BASE-FX Module The 100BASE-FX port module supports a connection to a Fast Ethernet network segment through a fiber optic connection. The module comes with two ST connectors. One labeled Tx is used for transmission. The other one labeled Rx is used for reception. Figure 3-3 100BASE-FX Port Module When connecting to a 100BASE-FX device using f ...

  • KTI Networks 2028 - page 21

    4. LED Indicators 4.1 LED Panel The switch provides comprehensive LED indicators for diagnosing and monitoring the operation of the unit as illustrated below: Figure 4-1 LED Indicators 4.2 Interpretation One Power LED indicates the status of the power supplied to the switch. Each port has two LEDs to indicate the port status including cable link, p ...

メーカー KTI Networks カテゴリー Switch

KTI Networks 2028のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2028の取扱説明書
- KTI Networksの製品カード
- パンフレット
- またはKTI Networks 2028の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、KTI Networks 2028の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、KTI Networks 2028の取り付け説明書、サービスマニュアル、簡易説明書、またはKTI Networks 2028のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、KTI Networks 2028の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

KTI Networks 2028デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKTI Networks 2028を使用するのを助ける技術的文書のことです。説明書は通常、全てのKTI Networks 2028ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

KTI Networksの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. KTI Networks 2028の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKTI Networks 2028の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。KTI Networks 2028に関してこのドキュメントで見つけることができる全てのヒントの目次
3. KTI Networks 2028デバイスの基本機能を使うにあたってのヒント。 KTI Networks 2028のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。KTI Networks 2028に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKTI Networks 2028のメーカー/サービスへの連絡先に関する情報。

KTI Networks 2028についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもKTI Networks 2028の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKTI Networks 2028で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)