Crimestopper Security Products CS-2004TW1の取扱説明書

24ページ 0.5 mb
ダウンロード

ページに移動 of 24

Summary
  • Crimestopper Security Products CS-2004TW1 - page 1

    SERIES II CS-2004TW1 with 2-Way AM Pager/Remote & 1-Way ‘Sidekick’ Remote CS-2004DC II with two 1-Way Remotes INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Security System by Cr imestopper Security Products Inc. This booklet contains the information necessary for installing, us ing, and maintaining your 2004T ...

  • Crimestopper Security Products CS-2004TW1 - page 2

    TABLE OF CONTENTS Installation Cautions & Warnings…….……………………………………………………………...………………2 Suggested Component Mounting………….…………………………………………………………….…………..3 Wiring……..………………………………………………? ...

  • Crimestopper Security Products CS-2004TW1 - page 3

    CONTROL MODULE / COMPONENT MOUNTING DO NOT Mount the control unit or wiring harness in the engine compartment or anywhere they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column. The alarm control module should be mounted in a concealed location. The antenna wire should be routed away from any metal if po ...

  • Crimestopper Security Products CS-2004TW1 - page 4

    WIRING BLUE WIRE: (-) HOOD/TRUNK TRIGGER The Blue wire is used for a grounding hood pin switch, trunk pin or both. Connect to existing hood and trunk pin switches that read ground when open. If no existing switches are available, install new pin switches if desired. GREEN WIRE: (-) DOOR TRIGGER Connect to Negative type door switches that read groun ...

  • Crimestopper Security Products CS-2004TW1 - page 5

    WIRING BLACK/WHITE WIRE: (+/-) OUTPUT FROM ON-BOARD 15A RELAY (Term #30, Step #3) Connect this wire to your Auxiliary device or Function. The function of this output depends on the connection of the Gray wire and the polarity of this output matches the White/Red wire. (See diagram below) Orange/Black Brown/Black Red/Black (-) Neg. Domelight Illumin ...

  • Crimestopper Security Products CS-2004TW1 - page 6

    WIRING MINI PLUGS: 2-PIN PLUG (SMALL): LED INDICATOR (RED FLASHING LIGHT) 2-PIN PLUG (LARGE): PROGRAM/OVERRIDE PUSH BUTTON TIP: The Sensor supplied with this system does not require any additional wiring, simply mount the sensor in a suitable location, plug in, and adjust to the desired levels of sensitivity. The Black dial is for Pre-warn level an ...

  • Crimestopper Security Products CS-2004TW1 - page 7

    WIRING BROWN/BLACK WIRE: (-) AUX. OUTPUT #1 OR M.A. P.-Mobile Accessories Protection (Optional) This is a programmable output wire that can operate two different ways: 1. 2. (DEFAULT Operation) A Remote Auxiliary Output that provides a ½ Second (-) Negative pulse when Button #3 is pressed and released to open a power trunk or hatch releas e. Conne ...

  • Crimestopper Security Products CS-2004TW1 - page 8

    POWER DOOR LOCK WIRING 6-PIN DOOR LOCK PLUG 18 GA. (Optional / ON-Board Relays): VIOLET: DOOR LOCK Relay Term. #87: Normally Open [Polarity Input for Lock relay] WHITE: DOOR LOCK Relay Term. #30: Common [Lock Output] GRAY: DOOR LOCK Relay Term. #87A: Normally Closed VIO/WHT: DOOR UNLOCK Relay Term. #87: Normally Open [Polarity Input for Unlock rela ...

  • Crimestopper Security Products CS-2004TW1 - page 9

    POWER DOOR LOCK DIAGRAMS UL REVERSE P OLA RITY DOOR LOCK WIRING + L NEGA TIVE TRIGGER D OORLOCK WIRING UL L NOT USED UNLO CK W I RE CUT LOCK W I RE CUT FAC T O RY LOCKING RELA YS UL L + A F TERMA RKET MOT OR DOOR L OCK WI RING UL L POS ITI VE TRI GGER DOO RLOCK WI RING FUSED +12V + UNLOCK W IRE LOCK W I RE FAC T O RY LOCKING RELA YS X = BLUE GREEN ...

  • Crimestopper Security Products CS-2004TW1 - page 10

    STARTER DISABLE WIRING STARTER DISABLE PLUG: (3) ORANGE 14 GA. WIRES: (PROGRAMMABLE: Normally Closed or Normally Open Configuration with ON-Board Relay ) Note: READ BELOW before connecting starter disable! Norm ally OPEN must be programmed to operate. See pg 13. Normally Closed Starter disable is the standard type used with most alarm systems today ...

  • Crimestopper Security Products CS-2004TW1 - page 11

    SYSTEM WIRING DIAGRAM IGNITION ST ARTER SWITCH PA R K I N G LIGHTS (+/-) On -Board Relay BA TTER Y - BLACK/WHITE 15A On-b oar d WHITE/RED GRA Y CUT IGNITION + SWITCH + CAR-JACK ENABLE OUTPUT (-)HOOD/T RUNK TRIGGER SWI TCH SIREN (-) ARMED (-)DOOR T RIGGER SWI TCH + DOOR T RIGGER PIN K VIOLET FUSE POLA RITY SELECT UNLOCK(87) GREEN POLA RITY SELECT LO ...

  • Crimestopper Security Products CS-2004TW1 - page 12

    CS-2004TW1 ANTENNA The following diagram pertains to the CS-2004TW1 two-way paging model only: WINDSHIELD ANTENNA LOCA TIONS CS-2004TW1 Black P lug Blue Plug RECOMMENDED Note Orientation of Black & Blue Pl ugs. Colors must match, or system will not operate! Transceiv er Box CS-2004TW1 Antenna System W indow Mount Antenna 12 ...

  • Crimestopper Security Products CS-2004TW1 - page 13

    OPTION PROGRAMMING You can program each option individually or multiple options in one session. You may start with the lowest option # and continue on to higher options without repeating the steps #1 through 3. To Engage Option Programming: 1. Turn Key to the ON position. 2. Press program / valet button 5 times, after a few sec onds the unit will f ...

  • Crimestopper Security Products CS-2004TW1 - page 14

    OPTION PROGRAMMING 1. AUTOLOCK WITH IGNITION This option controls whether the doors will automatically lock when the ignition is t urned on and will unlock when the ignition is turned off. 2. PASSIVE ARMING This option controls the Passive (Automatic) arming feature. If ON, arming will occur 30 Seconds after the ignition is turned off and the last ...

  • Crimestopper Security Products CS-2004TW1 - page 15

    OPTION PROGRAMMING 9. OPEN DOOR/ZONE WARNING (5 or 60 Seconds) This setting changes the delay time in which the alarm system begins to monitor the Door Zone. This is helpful on vehicles with a delayed dome light to prevent the alarm from giving warning chirps due to the vehicle’s dome light staying on. 10. DOOR LOCK/UNLOCK PULSE TIME Controls the ...

  • Crimestopper Security Products CS-2004TW1 - page 16

    CS-2004TW1 / CS-2004DC II REMOTE PROGRAMMING TRANSMITTER PROGRAMM ING NOTES (Read first!): (1) The CS-2004TW1 will learn up to 4 remotes, any co mbination of special CS-398TW 1-Way or CS-389LED 2- Way pager remotes. (2) The CS-2004DC II will up to 4 CS-404TX remotes. The remote controls for the CS-2004DC and the CS- 2004TW1 systems ARE NOT intercha ...

  • Crimestopper Security Products CS-2004TW1 - page 17

    CS-2004TW1 / CS-2004DC II REMOTE PROGRAMMING IGN OFF WAIT F O R 4 FL A SHES PRESS 4 X's FLA SH 2, 3, or 4 X' s IGN OFF PRESS TOGETHER "TW 1" OR SLNT AU X "DC" PRESS LOCK BTN SLNT AUX 17 ...

  • Crimestopper Security Products CS-2004TW1 - page 18

    OPERATION SLNT AUX ARM/ DISARM/ UNLOCK LOCK PA G I N G LED's SILENT/ AUX. 2 ANTENNA FIXED AUX. 1 #1 #2 #3 #4 CS-2004T W1 LED P AG ING REM OTE CS-2004DC II / CS-2004TW1 remote controls: SLNT #3 #1 #2 #4 LOCK TRU NK SILENT/ UNLOCK VEHICLE 2 FLA SHLIGHT AU X . # 1 AU X . # 2 AUX CS -2004 D C II CS-2004TW1 TWO-WAY PAGER OPERATION & PAGE TONES: ...

  • Crimestopper Security Products CS-2004TW1 - page 19

    OPERATION ACTIVE ARMING To arm the alarm and lock the doors, press the #1 Button on any remote. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock (optional) and the starter will be disabled. The red in- dash LED in the vehicle will begin to flash. After a short delay of 10-15 seconds to allo ...

  • Crimestopper Security Products CS-2004TW1 - page 20

    OPERATION SHOCK / IMPACT PROTECTION WITH PRE-WARNING Once the system is armed, if a low-level shock to the v ehicle body is detected, the pre-warning sensor activates with 5 siren chirps and one light flash as a Warn-Away feature. If a hard impact to the vehicle is detected the system will go into a full trigger cycle for 20 seconds. Adjust the s h ...

  • Crimestopper Security Products CS-2004TW1 - page 21

    OPERATION PASSIVE ARMING / PASSIVE LOCK MODES (PROGAMMABLE) If programmed, passive (Automatic) Arming will occur 30 Se conds after the ignition is turned off and the last door has been closed. The lights will flash twice when the last door is closed and the LED will begin flashing rapidly while counting down. If a door is reopened the countdown wil ...

  • Crimestopper Security Products CS-2004TW1 - page 22

    OPERATION CS-2004TW1 LED TRANSCEIVER (LOW BATTERY WARNING) CR2032 3V Lithium Battery T wist and Remove Battery cover w ith a Coin or Screwdriver Larger "+" Posi tive side of battery faces up CS2004TW1 BA TTER Y REPLACEMENT The CS-2004TW1 LED has a low battery warning system. When the battery voltage is low, the LED pager remote will stop ...

  • Crimestopper Security Products CS-2004TW1 - page 23

    2-VEHICLE OPERATION: (CS-2004DC II SYSTEM ONLY) 2-Vehicle method (CS-2004DC II SYSTEM ONLY): Your CS-2004DC II remote includes a push-button on the side for 2-car operation. You can only operate a second vehicle with a CS-2004DC II system installed. Your remote must be programmed to the second vehicle first. Read the following setup and operation d ...

  • Crimestopper Security Products CS-2004TW1 - page 24

    CARJACK PROTECTION PROGRAMMABLE PASSIVE CARJACK This feature provides Passive Carjack protecti on and must be enabled before use through Alarm programming options #7 & #12 on page 13. We recommend this mode should only be used in serious situations. When the Ignition is on (vehicle is running), and a door is opened, then closed, the Carjack cou ...

メーカー Crimestopper Security Products カテゴリー Automobile Alarm

Crimestopper Security Products CS-2004TW1のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CS-2004TW1の取扱説明書
- Crimestopper Security Productsの製品カード
- パンフレット
- またはCrimestopper Security Products CS-2004TW1の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Crimestopper Security Products CS-2004TW1の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Crimestopper Security Products CS-2004TW1の取り付け説明書、サービスマニュアル、簡易説明書、またはCrimestopper Security Products CS-2004TW1のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Crimestopper Security Products CS-2004TW1の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Crimestopper Security Products CS-2004TW1デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCrimestopper Security Products CS-2004TW1を使用するのを助ける技術的文書のことです。説明書は通常、全てのCrimestopper Security Products CS-2004TW1ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Crimestopper Security Productsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Crimestopper Security Products CS-2004TW1の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCrimestopper Security Products CS-2004TW1の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Crimestopper Security Products CS-2004TW1に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Crimestopper Security Products CS-2004TW1デバイスの基本機能を使うにあたってのヒント。 Crimestopper Security Products CS-2004TW1のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Crimestopper Security Products CS-2004TW1に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCrimestopper Security Products CS-2004TW1のメーカー/サービスへの連絡先に関する情報。

Crimestopper Security Products CS-2004TW1についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCrimestopper Security Products CS-2004TW1の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCrimestopper Security Products CS-2004TW1で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (1)

Николай

подскажите пожалуйста номер по каталогу сенсора для передвижения каретки по оси y и x для janome 350 e