Harmar Mobility RPL400の取扱説明書

22ページ 2.68 mb
ダウンロード

ページに移動 of 22

Summary
  • Harmar Mobility RPL400 - page 1

    This manual has been provided to assist you with lift installation and operation. For further assistance please contact your authorized Harmar dealer or Harmar’s Technical Service department. Tel: 866-378-6648 Fax: 816-537-0641  Residential  Platform  Lift RPL400 RPL600 HIGHLANDER ...

  • Harmar Mobility RPL400 - page 2

    Table of Contents Installing the lift Using the Manual 2 When You Receive the Lift 3 Specifications 3 Safety 3 Code Requirements 4 Site Requirements 4 Required Tools 4 Required Materials 4 Preparing to Install the Lift 5 Controller Harness Connections 5 Installing the outer guard panel 7 Installing the ramp 8 Anchoring the Lift 9 Setting the Limit ...

  • Harmar Mobility RPL400 - page 3

    When You Receive the Lift • Check the lift for shipping damage. If you see any dam age contact the freight carrier to file a da mage claim. • Verify the products match that described on the packing list attached to the exterior packaging. • Verify the contents of the package match that shown below to the right. Specifications Payload Capacity ...

  • Harmar Mobility RPL400 - page 4

    Code Requirements Your lift has been designed to meet ASME A18.1 section 5 and CSA B44/ASME A17.5, with the addition of certain options. Code requirements for Ve rtical Platform lifts vary depending on location. It is the installers responsibility to contact their local code enforcement office and d etermine all of the regulations they are subject ...

  • Harmar Mobility RPL400 - page 5

    Preparing to Install the Lift Final Site Inspection Verify the surface the lift will mount to is smooth and level. This surface m ust be made from 3,500 psi reinforced concrete with a minimum thickness of 4”. Verify that there is enough space for the lifts foot print. Be sure to include space for the folding access ramp. (49” x 69”) Caution: ...

  • Harmar Mobility RPL400 - page 6

    Installing the Platform Step 1 The mounting bolts, nuts and spacers that secure the platform to the lift carriage are preinstalled in the carriage flange. Begin by removing these pieces and setting aside. Step 2 Position the platform by aligning the support legs with the carriage flanges that protrude from the front cover. Step 3 Align the four mou ...

  • Harmar Mobility RPL400 - page 7

    Installing the Outer Guard Panel Step 1 Remove the hexbolts on the ends of the platform. Insert the guard panel posts into the pockets in the platform. The smooth side of the guard panel should face in towards the center of the platform. If you have a 90 degree exit platform, install the end guard panel using the provided bracket and bolt to inner ...

  • Harmar Mobility RPL400 - page 8

    Installing the Ramp Step 1 Install the ramp roller guide on the side of the lift tower using the screws already installed in the panels. Step 2 Attach the two ramp pivot tabs to the lower landing sides of the platform. Reinsert the hex bolts, one of which will go through the guard panel post, and tighten. Step 3 Attach the ramp to the pivot tabs us ...

  • Harmar Mobility RPL400 - page 9

    Anchoring the Lift Step 1 • Position the lift in its final location. • Verify that it is level and perpendicular to its surroundings. • Shim if necessary. Anchors Harmar recommends securing the lift using our Anchor Kit. If you purchase you own floor anchors they must use 1/2-13 bolts and have a minimum tensile strength of 6000 LBS. Warning: ...

  • Harmar Mobility RPL400 - page 10

    Setting the Limit Switches Your lift is equipped with upper and lower limit switches. The vertical location of these switches may be adjusted to fit your application. Typically the upper limit switch will need to be adjusted so the platform will stop level with the upper landing. The lower limit will typically not need adjusting. Step 1 Verify the ...

  • Harmar Mobility RPL400 - page 11

    Step 4 Loosen the bolts that attaches the upper limit switch assembly. Slide the assembly down the track until the lower switch in the assembly comes in contact with the l ift’s car. You should hear the limit switch click as contact is made. Retighten the set screw fastening the limit switch assembly in place. Step 5 Replace the front cover and s ...

  • Harmar Mobility RPL400 - page 12

    Verifying Operation of the Lift Caution: Complete the following section before training the customer to use the lift. Step 1 Run the lift up and down for 5 complete cycles. Hold the direction button down and allow the limit switches to stop the lift. At the top, verify that the platform stops level with the upper landing. At th e bottom, verify the ...

  • Harmar Mobility RPL400 - page 13

    Manual Override Your lift is equipped with a manual handcrank, to be used in the case of a power failure. Step 1 Before using the manual handcrank verify that it’s use is required. Check that the emergency stop switch is pulled out. Check that the electrical cord is plugged into the wall. Also check that the buildings cir cuit breaker has not tri ...

  • Harmar Mobility RPL400 - page 14

    Top Landing Gate (optional) The optional top landing gate is provided with a combination mechanical lock and electric contact (interlock) . The interlock: • Prevents the lift from running if the gate is not closed. • Prevents the gate from being opened if the platform is not at the top landing. • Unlocks when the lift is on the upper limit sw ...

  • Harmar Mobility RPL400 - page 15

    Top Landing EMI Interlock (optional) The optional EMI Interlock is provided with a combination mechanical lock and electric contact. They are to be used with existing doors. The interlock: • Prevents the lift from running if the door is not closed. • Prevents the door from being opened if the platform is not at the landing. • Unlocks when the ...

  • Harmar Mobility RPL400 - page 16

    Fascia Panel (optional) A fascia panel provides a smooth surface for th e platform edge to run against to prevent any shear or obstruction hazards and must be utilized. A running clearance of no more than 3/4” and no less than 3/8” must be maintained between the edge of the platform and the fascia panel. 16 ...

  • Harmar Mobility RPL400 - page 17

    Residential Platform Lift - Owners Section L Read the manual thoroughly before operating the lift. 17 ...

  • Harmar Mobility RPL400 - page 18

    Congratulations on the purchase of your Harmar Vertical Platform Lift. This lift has been engineered to provide trouble free se rvice for many, many years. Please read this manual completely before operating your lift. Safety • Do not exceed the maximum payload capacity of 600 lbs. • Do not ride on the lift until it is anchored in place. • Th ...

  • Harmar Mobility RPL400 - page 19

    Controls Emergency Stop In an emergency push this red button to stop the lift. Pull out on the button to run. Up Controls upward movement of lift platform. To move platform up, depress and hold the upper half of the rocker switch. To cease movement, release switch. Down Controls downward movement of lift platform. To move platform down, depress and ...

  • Harmar Mobility RPL400 - page 20

    Operating the Lift Step 1 - Up Drive onto and stop in the middle of the platform. Apply the brakes of your chair or scooter. Step 2 Verify that the emergency stop button is not activated by giving it a quick pull out, away from the side of the platform. Step 3 Press and hold the UP rocker. The lift will move in the up direction and stop when it rea ...

  • Harmar Mobility RPL400 - page 21

    Step 1 - Down Drive onto and stop in the middle of the platform. Apply the brakes of your chair or scooter. Step 2 Verify that the emergency stop button is not activated by giving it a quick pull out, away from the side of the platform. Step 3 Press and hold the DOWN rocker. The lift will move in the down direction and stop when it reaches the lowe ...

  • Harmar Mobility RPL400 - page 22

    Please fill out all fields and return within 10 days of product purchase. Toll-Free Fax: 1-866-234-5680, Online: www.harmar.com or Mail to: Harmar Summit, LLC., A ttn: Warranty Department 2075 47th Street, Sarasota, FL 34234 _____ Harmar warrants to the original purcha ser of a Highlander Re sidential vertical platform lift manufactured by us to be ...

メーカー Harmar Mobility カテゴリー Personal Lift

Harmar Mobility RPL400のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- RPL400の取扱説明書
- Harmar Mobilityの製品カード
- パンフレット
- またはHarmar Mobility RPL400の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Harmar Mobility RPL400の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Harmar Mobility RPL400の取り付け説明書、サービスマニュアル、簡易説明書、またはHarmar Mobility RPL400のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Harmar Mobility RPL400の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Harmar Mobility RPL400デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHarmar Mobility RPL400を使用するのを助ける技術的文書のことです。説明書は通常、全てのHarmar Mobility RPL400ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Harmar Mobilityの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Harmar Mobility RPL400の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHarmar Mobility RPL400の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Harmar Mobility RPL400に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Harmar Mobility RPL400デバイスの基本機能を使うにあたってのヒント。 Harmar Mobility RPL400のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Harmar Mobility RPL400に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHarmar Mobility RPL400のメーカー/サービスへの連絡先に関する情報。

Harmar Mobility RPL400についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHarmar Mobility RPL400の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHarmar Mobility RPL400で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)