Jensen XA2150の取扱説明書

12ページ 0.2 mb
ダウンロード

ページに移動 of 12

Summary
  • Jensen XA2150 - page 1

    How to Install and Operate the XA2150 Amplifier ® Contents T echnical Assistance For technical assistance with the operation or installation of the XA2150, call 1-800-323-0221. Welcome! What you're holding in your hands is no ordinary owner's manual. We've tried to make the instructions in this book clear and easy to follow . For yo ...

  • Jensen XA2150 - page 2

    2 ® XA2150 Amplifier Location The XA2150 amplifier’s compact design allows greater flexibility in mounting. It can be mounted under a seat or in the trunk. When selecting a location, remember that amplifiers generate heat. Select a location where air can circulate around the amplifier . Do not cover the XA2150 with carpets or enclose it behind i ...

  • Jensen XA2150 - page 3

    3 ® XA2150 Supplies and T ools Needed Supplies: • Speaker wire (12 gauge for subwoofers, 16-18 gauge for other speakers) • Sheet metal type screws for mounting amplifier • Electrical tape • Solderless crimp connectors • 1/2" thick plywood or particle board to mount amplifier on T ools: • Flat and Phillips screwdrivers • Wire cut ...

  • Jensen XA2150 - page 4

    4 ® XA2150 Wiring Power and Outputs Remote T erminal (RMT +12V) Power T erminal (BA TT +12V) Connect directly to the vehicle battery+ terminal with 8 gauge wire (minimum). Ground T erminal (GND) Connect to a good chassis ground. The ground connection should be to clean, unpainted metal to provide a good electrical connection. Connect the radio pow ...

  • Jensen XA2150 - page 5

    5 ® XA2150 Inputs and Contr ols Input Wiring Important Use only the low level or high level input, do not use both at one time. Low Level Input Use a pair of shielded stereo audio cables with RCA type jacks. Most trunk-mount amplifier installations require 20-foot RCA cables. Most under-seat and pickup truck installations use 12-foot cables. Conne ...

  • Jensen XA2150 - page 6

    6 ® XA2150 Adjust the crossover to accommodate your chosen installation method. Use LPF and HPF to adjust from 50 to 250Hz. When using your Jensen amplifier to run a subwoofer and two full- range speakers (known as T ri- mode or three channel operation) you will need to purchase separate high and low pass crossovers from your local retailer . A pa ...

  • Jensen XA2150 - page 7

    7 ® XA2150 Speaker Wiring 2 Subwoofers 2 Speakers L + L – R – R + RCA Cables 2/4 Ω 2/4 Ω LPF FULL HPF X-OVER 2/4 Ω 2/4 Ω RCA Cables L + L – R – R + LPF FULL HPF X-OVER 5311Eamp.p65 4/10/99, 8:14 PM 7 ...

  • Jensen XA2150 - page 8

    8 ® XA2150 Bridged Subwoofer 2 Speakers + Subwoofer Important When running a subwoofer and two full-range speakers together (T ri-mode operation), high and low pass filters must be used. Failure to install these filters will damage your amp and/ or speakers. RCA Cables 2/4 Ω 4 Ω 2/4 Ω L + L – R – R + Low Pass Filter (available at most ca ...

  • Jensen XA2150 - page 9

    9 ® XA2150 T est Power Wiring 1. T urn on the receiver but do not turn up the volume. The amplifier power light should come on. If not, check the RMT and +12V wires. 2. T urn up the receiver volume slightly . All speakers should operate. If not, check wiring connections at amplifier and speakers. ✓ T esting T est Speaker Connections These tests ...

  • Jensen XA2150 - page 10

    10 ® XA2150 Professional Tip Crimp Connections Purchase crimp connectors and crimping tool. Connectors are color coded. 1. Strip 1/4 inch (6mm) of insulation from both wires. 2. Insert into connector . 3. Crimp tightly . Y ou can make permanent splices (using butt connectors) or select connectors that can be removed and reinstalled. 3 2 1 Strip wi ...

  • Jensen XA2150 - page 11

    11 ® XA2150 T r oubleshooting Problem Possible Cause Corrective Action Amplifier does not operate (power LED not on) when vehicle and radio are on Radio volume needs to be turned up too high for amp to work Radio volume is too sensitive Sound from only one speaker Sound distorted Blows fuses Alternator whine in outputs (vehicle ignition noise) Lou ...

  • Jensen XA2150 - page 12

    Specifications XA2150 Amplifier Power output @ 14.4 VDC, 20-20 kHz ............ (4 ohms) 75 W atts per channel RMS, < 00.08% THD (2 ohms) 100 W atts per channel RMS, < 00.1% THD (4 ohms) bridged 200 W atts per channel RMS, < 00.1% THD Frequency Response ....................................................................................... ...

メーカー Jensen カテゴリー Car Amplifier

Jensen XA2150のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- XA2150の取扱説明書
- Jensenの製品カード
- パンフレット
- またはJensen XA2150の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Jensen XA2150の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Jensen XA2150の取り付け説明書、サービスマニュアル、簡易説明書、またはJensen XA2150のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Jensen XA2150の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Jensen XA2150デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJensen XA2150を使用するのを助ける技術的文書のことです。説明書は通常、全てのJensen XA2150ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Jensenの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Jensen XA2150の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJensen XA2150の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Jensen XA2150に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Jensen XA2150デバイスの基本機能を使うにあたってのヒント。 Jensen XA2150のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Jensen XA2150に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJensen XA2150のメーカー/サービスへの連絡先に関する情報。

Jensen XA2150についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJensen XA2150の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJensen XA2150で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)