Makita BHR202の取扱説明書

13ページ 3.07 mb
ダウンロード

ページに移動 of 13

Summary
  • Makita BHR202 - page 1

    Models No. Description PR ODUCT T ECHNICAL INFORMA TION C ONCEPT AND MAIN APPLICA TIONS S pecif ication S tandard equipment O ptional accessories P 1 / 13 BHR202 Cordless Combination Hammer H L Dimensions: mm (") W idth (W) Height (H) Length (L) 358 (14-1/8) 84 (3-5/16) 259 (10-1/4) These new products are a vailable in the follo wing variation ...

  • Makita BHR202 - page 2

    [2] LUBRICA TION [1] NECESSAR Y REP AIRING TOOLS CA UTION: Remove the bit and the battery from the machine f or safety bef ore repair/ maintenance in accordance with the instruction manual! R epair Description Code No. Use for Retaining ring S pliers ST -2 1R004 Removing Ring spring 29 Retaining ring S pliers ST -2N 1R003 Removing Ring spring 19 Be ...

  • Makita BHR202 - page 3

    [2] LUBRICA TION (cont.) R epair P 3 / 13 Fig. 2 Item No. Description Portion to lubricate Lubricant Amount Striker Ball bearing 606ZZ Compression spring 7 Disassemble T ool holder section as illustrated in Fig . 3 . Retaining ring S-7 Piston joint Armature Flat washer 12 Swash Bearing Section 40 41 51 52 53 63 (f) (g) (h) (g) (k) Crank room (i) (j ...

  • Makita BHR202 - page 4

    R epair P 4 / 13 [3] DISASSEMBL Y/ASSEMBL Y [3] -2. Change Lev er DISASSEMBLING ASSEMBLING Change le ver Drill mode Lock button Pushing Lock button into Change le ver , turn Change le ver fully to Drill mode until it stops. Remov e Change lever by le vering up it with Slotted head scre wdriv er, inserted between Gear housing complete and Change le ...

  • Makita BHR202 - page 5

    R epair P 5 / 13 bearing room of Gear housing complete 4x40 T apping scre ws (4 pcs.) Gear housing complete Holder cap cov er Motor housing complete Ball bearing 6000DD W of Armature (behind the Fan) [3] DISASSEMBL Y/ASSEMBL Y [3] -4. Armature 1) Remov e Holder cap cover by inserting Slotted scre wdriv er between Holder cap cover and Motor housing ...

  • Makita BHR202 - page 6

    R epair P 6 / 13 [3] DISASSEMBL Y/ ASSEMBL Y [3] -5. T or que Limiter Section (cont.) ASSEMBLING Do the rev erse of disassembling steps. Note: Do not forget to assemble Flat w asher 28 between T orque limiter section and Inner housing complete. Refer to Fig. 12 . [3] DISASSEMBL Y/ASSEMBL Y [3] -6. Needle Bearing Complete and Oil Seal 25 DISASSEMBLI ...

  • Makita BHR202 - page 7

    R epair P 7 / 13 DISASSEMBLI NG 1) Referring to " [3] -5. T orque Limiter Section ", disassemble Ring spring 29, W asher 31, Compression spring 32 and Spur gear 51 from T ool holder complete. Refer to Figs. 11 to 14 . 2) Holding Gear housing complete in vise and 1R038, T ap Ring spring 28 in T ool holder complete as illustrated in Figs. 2 ...

  • Makita BHR202 - page 8

    [3] DISASSEMBL Y/ASSEMBL Y [3] -7. Impact Bolt Section (cont.) DISASSEMBLING ASSEMBLING Fig. 29 Note: Use an extra Piston c ylinder as a jig. Never use Piston c ylinder that is to be assembled to the machine. 2) Push Ring spring 28 with Piston cylinder until it f its to the inner groove of T ool holder complete. ( Fig. 29 ) 1) Disassemble T ool hol ...

  • Makita BHR202 - page 9

    [3] DISASSEMBL Y/ASSEMBL Y [3] -8. Swash Bearing Section (cont.) DISASSEMBLING Fig. 32 Fig. 33 6) Mov e Piston cylinder to the rear dead center position ( Fig. 32 ). 7) Remov e Swash bearing section from Inner housing by pulling in the direction of the arrow . Then, remo ve Change plate from the groov e of Clutch cam. ( Fig. 33 ). Piston cylinder S ...

  • Makita BHR202 - page 10

    [3] DISASSEMBL Y/ASSEMBL Y [3] -8. Swash Bearing Section (cont.) DISASSEMBLING ASSEMBLING 1R032 1R033 Fig. 39 Swash bearing 10 Helical gear 26 Retaining ring S-7 Compression spring 7 Spur gear 10 Cam shaft Cam shaft Clutch cam 1) Assemble Swash bearing section using 1R032, 1R033, 1R291 and arbor press as illustrated in Fig. 39 . Note: Be sure to pu ...

  • Makita BHR202 - page 11

    [[3] DISASSEMBL Y/ASSEMBL Y [3] -8. Swash Bearing Section (cont.) R epair ASSEMBLING P 11 / 13 4) Mov e Piston cylinder to the rear dead center position. ( Fig. 42 ) 5) Insert the pole of Swash bearing 10 into the hole of Piston joint as illustrated in Fig . 43 . 6) Insert Ring 8 (the end of Swash bearing section) into Inner housing complete. ( Fig ...

  • Makita BHR202 - page 12

    R epair Fig. 47 ov al hole of F/R change lev er protrusion of Switch P 12 / 13 M aintenance program It is recommended to replace the follo wing parts shown belo w and apply lubricant to the specific parts designated in Figs. 2 and 3 when replacing Carbon brushes. [3] DISASSEMBL Y/ASSEMBL Y [3]-9. F/R Change Lev er Fit the protrusion of Switch into ...

  • Makita BHR202 - page 13

    W iring diagram P 13 / 13 Fig. D-2 C ircuit diagram Color index of lead wires' sheath Black White Blue Orange Y ello w Red Switch T erminal T ape Light circuit LED Y oke unit FET Heat dissipation plate (Housing L side) (Housing R side) Fig. D-1 Connector Brush holder Note : Route Lead wires for switch to each lead wire holders and guide them b ...

メーカー Makita カテゴリー Power Hammer

Makita BHR202のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- BHR202の取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita BHR202の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita BHR202の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita BHR202の取り付け説明書、サービスマニュアル、簡易説明書、またはMakita BHR202のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita BHR202の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita BHR202デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita BHR202を使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita BHR202ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita BHR202の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita BHR202の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita BHR202に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita BHR202デバイスの基本機能を使うにあたってのヒント。 Makita BHR202のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita BHR202に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita BHR202のメーカー/サービスへの連絡先に関する情報。

Makita BHR202についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita BHR202の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita BHR202で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)