-
Delta 78-904 - page 1
INSTRUCTION MANUAL D A T E D 3-5-96 P A R T NO. 1349984 'Delt a International Machinery Corp. 1996 Biesemeyer fi T -Square fi Commercial Fence Systems 5 0 C a p acity (Model 78-904) 3 0 C a p acity (Model 78-907) ...
-
Delta 78-904 - page 2
INTRODUCTION The 50 cap acity (model 78-904) and 30 c a p acity (model 78-907) Biesemeyer fi T -Square fi Commercial fence systems are specially designed to be used with: Delt a 1 0 T i l t i n g Arbor Unisaws fi Delt a 1 0 T i l t i n g Arbor Saws Delt a 1 0 Contractor s fi Saws Delt a 1 0 Contractor s fi Saws II The T -Square fi Commercial ...
-
Delta 78-904 - page 3
If you purchased the accessory right extension t able (model 78-925 for 50 c a p acity fence or model 78-927 for 30 c a p acity fence) carefully unp ack the extension t able from the shipping cont ainer . Figure 3 illustrates the right extension t able removed from the cont ainer . NOTE: I f you did not purchase the accessory right extension t able ...
-
Delta 78-904 - page 4
Fig. 4 If you purchased the accessory leg kit (model 78-952) for use with the right extension t able, Figure 4 illustrates the legs and loose items supplied with this accessory . 1 - Legs (2) 2 - 5 / 8 long wood screws #8 (8) 3 - 1/4-20 x 1-1/2 lo ng flat head Phillip s screws (4) 4 - 1/ 4 flat washers (4) 5 - 1/4-20 hex nut s ( 4 ) ASSEMBL Y INSTR ...
-
Delta 78-904 - page 5
Fig. 5 Fig. 6 Fig. 7 Fig. 8 2 . Assemble the front rail (A) Fig. 5, to front of saw t able using the two 3/8-16 x 1-1/4 long flat head Phillip s screws (B), 7/8 flat washers, lock washers and 3/8-16 hex nut s supplied. Screws (B) are inserted through the two holes in the front rail, as shown and through the two through holes in the front of the saw ...
-
Delta 78-904 - page 6
6 Fig. 9 Fig. 10 Fig. 1 1 8 . Position the two legs (H) Fig. 10, at the two far corners of the inside of one end of the extension t able, as shown, and mark the position of the eight holes to be drilled into the bottom of the t able. IMPORT A N T : I f your saw and fence system will be used with a mobile base under - neath the saw base and t able l ...
-
Delta 78-904 - page 7
Fig. 12 Fig. 13 Fig. 14 Fig. 15 1 0. Fasten the leg bracket (L) Fig. 12, to the end piece (J) of the t able using the two 1-1/2 long flat head P h i l l i p s screws, flat washers and hex nut s (M ) Figs. 1 1 and 12. Fasten the remaining leg to the extension t able in the same manner . 11 . Figure 13 illustrates the two legs (H) assembled to the bo ...
-
Delta 78-904 - page 8
Fig. 17 Fig. 18 Fig. 19 1 6. Figure 19 illustrates the switch and nipple (W) assembled to the switch adapter (X). The switch adapter will be fastened to the front rail (A) and guide tube through holes (Y) i n the front rail af ter the guide tube is fastened to the front rail (A). 1 5 . Assemble the switch and nipple (W) Fig. 18, to switch adapter f ...
-
Delta 78-904 - page 9
Fig. 20 Fig. 21 Fig. 22 Fig. 23 1 7 . Lay the guide tube (B) Fig. 20, on the saw t able as shown, and line up the threaded holes (C) on bottom of guide tube (B) with the through holes (D) on the front rail ( A ) . IMPORT A N T : I f a s w i t c h a d a p t e r i s b e i n g u s e d f o r Unisaws or 10 Contractor s Saws to mount the switch to the ra ...
-
Delta 78-904 - page 10
Fig. 24 Fig. 25 Fig. 26 FENCE OPERA TION IMPORT A N T : Before operating fence, make sure the fence is adjusted p arallel to the miter gage slot, as explained later on in this manua l . 1 . T o move the fence along the guide rail, simply lif t up clamp lever (A) a s shown in Fig. 24, slide fence to desired position on rail, and push down on clamp l ...
-
Delta 78-904 - page 11
Fig. 27 Fig. 28 Fig. 29 Fig. 30 ADJUSTING FENCE P ARALLEL T O MITER GAGE SLOTS NOTE: Delt a t able saws have been aligned at the factory so that the miter gage slot s i n the t able are p arallel with the saw blade. It is recommended, however , t o check and make cert ain this alignment is correct before adjust - ing the fence p arallel to the mite ...
-
Delta 78-904 - page 12
LUBRICA TION 1 . Apply p aste wax to fence and guide tube sliding sur - faces weekly . Also, saw t able and extension t able surface should be waxed of t e n . 2 . Apply grease to cam lock (A) Fig. 31, and cam foot (B) occasionally to prevent wear . Fig. 31 Delt a will rep air or replace, at it s expense and at it s option, any Delt a machine, mach ...
Delta 78-904についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもDelta 78-904の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta 78-904で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。