PYLE Audio 352VSの取扱説明書

17ページ 0.2 mb
ダウンロード

ページに移動 of 17

Summary
  • PYLE Audio 352VS - page 1

    Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...

  • PYLE Audio 352VS - page 2

    2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are ...

  • PYLE Audio 352VS - page 3

    3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry pro ...

  • PYLE Audio 352VS - page 4

    4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work a ...

  • PYLE Audio 352VS - page 5

    5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose ...

  • PYLE Audio 352VS - page 6

    6 ADDITIONAL SPECIFIC SAFETY RULES SAVE THESE INSTRUCTIONS! 1. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. Use proper safety equ ...

  • PYLE Audio 352VS - page 7

    7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g ........................ grams kg ........... ...

  • PYLE Audio 352VS - page 8

    Extreme care should be taken when removing paint. The peelings, residue, and vapors of paint may contain lead, which is poisonous. Exposure to even low levels of lead can cause irreversible brain and nervous system damage. Young and unborn children are particularly vulnerable. Before beginning any paint removal process you should determine whether ...

  • PYLE Audio 352VS - page 9

    9 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 vo ...

  • PYLE Audio 352VS - page 10

    10 OPERA TION NOTE: This tool is shipped completely assembled. No assembly time or tools are required. ASSEMBL Y 1. Place the sander on its left side. 2 . Pull the lever (A) Fig. 1 out toward the front of the machine to retract the idler pulley (B) and release the tension on the abrasive belt. 3. Remove the old belt. 4. Install the new belt with th ...

  • PYLE Audio 352VS - page 11

    TRACKING THE ABRASIVE BEL T To prevent excessive wear on both the sander and belt, NEVER allow the abrasive belt to rub on the sander frame. To make sure that the belt is tracking correctly, do the following: Make sure that the trigger switch is “ OFF” before con- necting the tool to the power source. 1. Turn the tool over. Hold the rear handle ...

  • PYLE Audio 352VS - page 12

    12 SELECTING AN ABRASIVE BEL T The principle abrasive materials used on belts for machine sanding are aluminum oxide and silicon carbide. Aluminum oxide is the softer of the two, but is tougher and more suited for woods and soft (non-ferrous) metals. Silicon carbide is extremely hard and is best suited for surfacing stone, marble, and glass. Abrasi ...

  • PYLE Audio 352VS - page 13

    13 Overlap the strokes and cover the entire surface, working from both sides of the board (angle left and then angle right.) Smooth the surface by guiding the sander back and forth with the grain. Change the belt to a medium grit and follow the same procedure. Finish by thoroughly working the grain lengthwise. Change again to a fine grit and repeat ...

  • PYLE Audio 352VS - page 14

    14 BE CAREFUL when sanding at the end of a board. Keep the tool level and flat on the work surface. Don’t let the front of the tool drop. (Fig. 6). If this happens, it will round the edge. The model 352VS sander works very fast and can do a thorough job in a fraction of the time required by hand sanding. Do not rush the job. Give every surface a ...

  • PYLE Audio 352VS - page 15

    15 REPLACEMENT P ARTS When servicing use only identical replacement parts. For a service parts list or to learn more about Porter-Cable visit our website at www.porter-cable.com SERVICE AND REP AIRS All quality tools will eventually require servicing, or replacement of parts due to wear from normal use. For assistance with your tool, visit our webs ...

  • PYLE Audio 352VS - page 16

    16 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...

  • PYLE Audio 352VS - page 17

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

メーカー PYLE Audio カテゴリー Sander

PYLE Audio 352VSのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 352VSの取扱説明書
- PYLE Audioの製品カード
- パンフレット
- またはPYLE Audio 352VSの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、PYLE Audio 352VSの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、PYLE Audio 352VSの取り付け説明書、サービスマニュアル、簡易説明書、またはPYLE Audio 352VSのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、PYLE Audio 352VSの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

PYLE Audio 352VSデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPYLE Audio 352VSを使用するのを助ける技術的文書のことです。説明書は通常、全てのPYLE Audio 352VSユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

PYLE Audioの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. PYLE Audio 352VSの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPYLE Audio 352VSの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。PYLE Audio 352VSに関してこのドキュメントで見つけることができる全てのヒントの目次
3. PYLE Audio 352VSデバイスの基本機能を使うにあたってのヒント。 PYLE Audio 352VSのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。PYLE Audio 352VSに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPYLE Audio 352VSのメーカー/サービスへの連絡先に関する情報。

PYLE Audio 352VSについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPYLE Audio 352VSの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPYLE Audio 352VSで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)