Bulldog Security 500の取扱説明書

27ページ 0.34 mb
ダウンロード

ページに移動 of 27

Summary
  • Bulldog Security 500 - page 1

    . . ...

  • Bulldog Security 500 - page 2

    . . WARRANTY Bulldog Warranty Information All Bulldog models have a Limited Lifetime W arranty on the main control module. All parts excluding the control module have a two y ear warranty against defects in workmanship, This includes shock sensors, remote tr ansmitters and sirens. The control module will be repaired or replaced at our discretion fo ...

  • Bulldog Security 500 - page 3

    . . 3 TABLE OF CONTENTS Important Notice ................................................................... 4 A. REMOTE TRANSMIT TER OPERA TION .....................................5 B. TWO-W AY TRANSEIVER REMO TE CONTROL OPERATION .........6 C. LED DISPLAY CHART .......................................................... 6 D. CHIRP INDICA TOR .... ...

  • Bulldog Security 500 - page 4

    . . 4 WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of . 1. Keep all transmitters out of the reach of children 2. Do not lea ve anyone in the vehicle while running in remote control mode. 3. Notify servicing personnel that the vehicle can be remote started. ...

  • Bulldog Security 500 - page 5

    . . 5 A. REMOTE TRANSMITTER OPERATION: Transmitter Button System Function or Feature Remark Lock Doors & Arm the Security System Car Locator Works when armed only (3 sec.) Panic function Press and hold for 3 sec. + Silent Arming / Disarming Ign. in the "Off" position. Unlock Doors & Disarm System - T wo Steps Door Unlock & Dis ...

  • Bulldog Security 500 - page 6

    . . 6 OPERATION B. TWO-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION: Transceiver Button System Function Remark SET - SET - (C) System s Status Check Press within 3 sec. SET - ( ) Monitor Indoor T emperature Press within 3 sec. SET - ( ) Daily Timer Start Press within 3 sec. SET (1 sec.) LCD screen lamp turns on for 5 seconds. Press and hold for ...

  • Bulldog Security 500 - page 7

    . . 7 OPERATION G. ACTIVE ARMING  LOCK & ARM: 1. Press the button on the transmitter . 2. The siren will chirp once and parking lights will flash once and remain ON for 10 seconds indicating that the system is now armed. The vehicles doors will lock upon arming when interfaced with the security systems keyless entry . System Arm Door Ajar Cl ...

  • Bulldog Security 500 - page 8

    . . 8 OPERATION H. SILENT ARMING / DISARMING: Pressing the transmitters and buttons at the same time will arm or disarm your security system, No chirping sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only. I. PASSIVE STARTER DISABLE : The purpose of this feature is to protect the vehicle from being stole ...

  • Bulldog Security 500 - page 9

    . . 9 OPERATION K. ACTIVE DISARMING  UNLOCK & DISARM: 1. Press the button on the tr ansmitter . 2. The siren will chirp (2) times and parking lights will flash (2) times and then remain ON for 30 seconds indicating that the security system is now disarmed. The vehicle s doors will unlock and dome light will turn ON for 30 seco ...

  • Bulldog Security 500 - page 10

    . . 10 OPERATION Enter Valet Mode: 1 . With the unit Disarmed, turn the ignition to ON position. 2. Press and hold valet/program switch for 2 seconds until the LED turns ON . The LED wills remain on as long as the system is in Valet Mode . Exit Valet Mode: 1 . T o return to normal operation, turn the ignition ON . 2. Press a ...

  • Bulldog Security 500 - page 11

    . . 11 OPERATION O. PANIC MODE: The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency . 1. Press and hold the button for 3 second. The alarm will immediately sound. 2. During Panic Mode , the normal function of this trans- mitter button will be suspended. The and buttons can be used to lock and u ...

  • Bulldog Security 500 - page 12

    . . 12 OPERATION S. TRUNK RELEASE (CHANNEL 3) OUTPUT. Press and hold the button on the transmitter for two sec- onds to remote control the trunk release or other connected electronic devices. T. CHANNEL 4 TIMER CONTROL OUTPUT Press the transmitters (4) and (4) buttons at the same time to activ e the Channel 4 function . Channel 4 is user -programma ...

  • Bulldog Security 500 - page 13

    . . 13 OPERATION For 2-way LCD Remote Control Transceiver: 2nd Car Operation: 1 . Press the SET button first, within 3 seconds press and hold the and buttons together for 2 seconds with two beeping sounds and the   icon will display on the LCD screen to indicate the second transceiver pin code has been learned. 2 . With the   icon displ ...

  • Bulldog Security 500 - page 14

    . . 14 OPERATION A. TO REMOTE START THE VEHICLE: When you want to R emote Start your vehicle, 1 . Press the button twice on the transmitter 2 . The parking light will flash to indicate the remote starter received the signal. (A melody sounding from your R emote LCD transceiver and the  icon will flash on the LCD screen to confirm the remote s ...

  • Bulldog Security 500 - page 15

    . . 15 OPERATION B. ENGINE START MEMORIZING FOR VEHICLES WITH MANUAL TRANSMISSIONS The system senses the neutral tr ansmission position automatically and there is no prior set -up required. The system in the standard transmission vehicle operates a process that when you exit the v ehicle it senses and memorizes the neutral transmission position. If ...

  • Bulldog Security 500 - page 16

    . . 16 OPERATION D. PIT-STOP FEATURE: This feature allows the vehicle to remain running after the key has been removed from the ignition switch. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the engine running and the climate control on . 1. Before turning off the ...

  • Bulldog Security 500 - page 17

    . . 17 OPERATION 2 to 3 hour Timer Start with Temperature-Control OFF: This feature is design for an extreme cold climate usage. The system will automatically start the vehicle every 2 or 3 hours, to prevent the engine from freezing and to prevent a vehicle from being hard to start. A MAXIMUM OF SIX CYCLES CAN OCCUR. 2 to 3 hour timer s ...

  • Bulldog Security 500 - page 18

    . . 18 REMOTE START OPERATION Exit the timer start: 1 . Timer start can be exited manually as follows: Make sure the engine is not running in remote start mode. 2 . T urn the ignition key ON . The LED and parking lights will flash (4) times. The horn chirps (4) times. Or 1. Press the button twice to remote start the vehicle. As soon as the vehicle ...

  • Bulldog Security 500 - page 19

    . . 19 REMOTE START OPERATION I. SHUT-DOWN INPUT FOR REMOTE STARTER: If any of the following conditions exists while the system is operating, the engine will not start or will shut down immediately: 1. The hood is opened. 2. The brake pedal is pressed. 3. The emergency brake is released (for Standard T ransmission Vehicle) 4. Engine is over-revved. ...

  • Bulldog Security 500 - page 20

    . . 20 REMOTE START OPERATION K. BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote T ransceiver . When the power of the battery weakens a icon will be displayed on the LCD screen. When the old battery is replaced with a new one, there will be beep sound that indicates the power is up and the clock on the LCD screen returns to ...

  • Bulldog Security 500 - page 21

    . . 21 REMOTE START OPERATION Time Monitor Alert Alarm Y ou have set the morning call alarm. Count Down (Parking) Timer Power Save Mode Reminder when your time is Saves the battery power . up for parking. Vibration Mode Button Lock Remote control vibr ate when Disable the transmission the system is triggered. functions tempor arily . Low Battery Y ...

  • Bulldog Security 500 - page 22

    . . 22 REMOTE START OPERATION Transmitter Description Operation Button SET - (2-sec.) Progr am Count Down Timer ( ) Press within 3 seconds (10-Minute/20M/30 M/1Hour/ *let the buttons start 1.5H/2.0H) counting down then flashes SET - (2-sec.) Enable/Disable Beep Sound ( Bi ) While Pressing Button 1. Screen Lamp ON: Press and hold the SET button one ...

  • Bulldog Security 500 - page 23

    . . 23 LCD REMOTE CONTROL TRANSCEIVER 7. Enable / Disable Beep Sound While Pressing Button: It has a short bi sound while pressing the button of the LCD screen transceiver . If you want mute the bi sound mute always while press button. Press the button first, within 3 seconds press and hold the ( Bi ) button for 2 seconds to disable the ...

  • Bulldog Security 500 - page 24

    . . 24 LCD REMOTE CONTROL TRANSCEIVER Transceiver Press Button Description Transceiver Button 2 Press the SET button once. Alert Alarm for  and or + Time Setting (Hour) *Flash digit for adjusting Press the SET button once Alert Alarm for  and for + Time Setting (Minute) *Flash digit for adjusting Press the SET button once Alert Alarm Setting ...

  • Bulldog Security 500 - page 25

    . . 25 LCD REMOTE CONTROL TRANSCEIVER EXIT : Press and hold the SET button for 2 seconds or leav e it for 10 seconds, the system will exit the programming mode. 1. Timer Setting: Example to AM10:30 1. Press and hold the SET button for 3 seconds, with two-melody sound and the Hours digit flashes for adjusting. 2. Press the or button to decreas ...

  • Bulldog Security 500 - page 26

    . . 26 LCD REMOTE CONTROL TRANSCEIVER 3. Count Down Timer Setting: Example Set count down timer at 2:30 1. Press and hold the SET button for 3 seconds, with two-melody sound and the Hours digit flashes for adjusting. 2. Press the SET button 5 times, the LCD screen will shows icon and Hours digit is flashes for adjusting. 3. Press the or ...

  • Bulldog Security 500 - page 27

    . . ...

メーカー Bulldog Security カテゴリー Automobile Alarm

Bulldog Security 500のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 500の取扱説明書
- Bulldog Securityの製品カード
- パンフレット
- またはBulldog Security 500の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bulldog Security 500の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bulldog Security 500の取り付け説明書、サービスマニュアル、簡易説明書、またはBulldog Security 500のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bulldog Security 500の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Bulldog Security 500デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBulldog Security 500を使用するのを助ける技術的文書のことです。説明書は通常、全てのBulldog Security 500ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bulldog Securityの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bulldog Security 500の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBulldog Security 500の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bulldog Security 500に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bulldog Security 500デバイスの基本機能を使うにあたってのヒント。 Bulldog Security 500のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bulldog Security 500に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBulldog Security 500のメーカー/サービスへの連絡先に関する情報。

Bulldog Security 500についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBulldog Security 500の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBulldog Security 500で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (1)

Виталий

Saeco Magic de Luxe SUP012R. Имеется на работе кофе-машина, вроде функционирует исправно, но подозрения, что мало воды льет в случае "американо"(большая чашка) и нормально в "expresso" (маленькая чашка). Декальцинацию делали. Почему ? Может настройка кол-ва воды есть в программировании?