Whirlpool WHES40の取扱説明書

23ページ 1.16 mb
ダウンロード

ページに移動 of 23

Summary
  • Whirlpool WHES40 - page 1

    7323441 (Rev G 9/7/1 1) Product No. 8562922-B Manufactured and warranted by Ecodyne W ater Systems 1890 Woodlane Drive Woodbury , MN 55125 How to inst all, operate and maintain your Demand Controlled W ater Softener Model WHES40 Do not return water softener to store I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l System tested and certi ...

  • Whirlpool WHES40 - page 2

    W A TER SOFTENER W ARRANTY W arrantor: Ecodyne W ater Systems, 1890 Woodlane Drive, Woodbury , MN 55125 W arrantor guarantees, to the original owner , that: One Y ear Full Warranty: For a period of one (1) year after installation, all parts will be free from defects in materials and workmanship and will perform their normal functions. For a period ...

  • Whirlpool WHES40 - page 3

    3 FIG . 1 Specifica tions & Dimensions Questions? Call T oll Free 1-866-986-3223 Monday- Friday , 8 AM - 7 PM EST or visit www .ecodynewatertreatment.com When you call, please be prepared to provide the model, date code and serial number , found on the rating decal, typically located on the rim below the salt lid hinges. 39-1/2” 47-7/8” 3-3 ...

  • Whirlpool WHES40 - page 4

    4 W a ter Softener Saf ety Bef or e Y ou Star t Y our saf ety and the safety of others ar e v er y impor tant. We have provided many safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All sa ...

  • Whirlpool WHES40 - page 5

    5 Packing List Inspect Shipment Ground Clamp Kit 20 ft. Drain Hose Bypass V alve Clips Adaptor Elbow Installation Adaptors FIG . 2 Hose Clamps Grommet O-rings W ater Hardness T est S trip W a ter Conditioning Inf or mation IRON Iron in water can cause stains on clothing and plumb- ing fixtures. It can negatively affect the taste of food, drinking w ...

  • Whirlpool WHES40 - page 6

    6 PLUMBING CODES All plumbing must be completed in accordance with national, state and local plumbing codes. LAUNDR Y TUB ST ANDPIPE 1-1/2” air gap FLOOR DRAIN In the state of Massachusetts: The Commonwealth of Massachusetts plumbing code 248-CMR shall be adhered to. A licensed plumber shall be used for this installation. AIR GAP REQUIREMENTS A d ...

  • Whirlpool WHES40 - page 7

    7 Installa tion R equir ements V AL VE DRAIN REQUIREMENTS Using the flexible drain hose (included), measure and cut to the length needed. Flexible drain hose is not allowed in all localities (check your plumbing codes). If local codes do not allow use of a flexible drain hose, a rigid valve drain run must be used. Purchase a com- pression fitting ( ...

  • Whirlpool WHES40 - page 8

    8 Installa tion Instr uctions TYPICAL INST ALLA TION Inlet Outlet Clips Ground Clamp T o Outside Faucets Single Bypass V alve Ground Clamp Conditioned W ater Hard Water Main Water Pipe Plug-in T ransformer W ater Softener V alve T o Controller V alve Drain Elbow V alve Drain Hose* *Do not connect the water softener valve drain tubing to the salt st ...

  • Whirlpool WHES40 - page 9

    9 MOVE THE W A TER SOFTENER INTO PLACE 1 . Move the water softener into the desired location. Set it on a solid, level surface. IMPORT ANT : Do not place shims directly under the salt storage tank to level the softener . The weight of the tank, when full of water and salt, may cause the tank to fracture at the shim. 2 . Visually check and remove an ...

  • Whirlpool WHES40 - page 10

    10 FIG . 13 Ground Clamp Electrical Shock Hazard Inst all metal ground clamp to metal house water supply pipe before beginning inst allation. Securely tighten connection in center of met al ground clamp. Failure to do so can result in death or electrical shock. COMPLETE INLET AND OUTLET PLUMBING Measure, cut, and loosely assemble pipe and fittings ...

  • Whirlpool WHES40 - page 11

    11 Excessive Weight Hazard Use two or more people to move and lif t salt bags. Failure to do so can result in back or other injury . ADD W A TER AND SAL T TO THE SAL T STOR AGE T ANK Installa tion Instr uctions TEST FOR LEAKS T o prevent air pressure in the water softener and plumbing system, complete the following steps in order: 1 . Fully open tw ...

  • Whirlpool WHES40 - page 12

    12 FIG . 16 FIG . 17 When the transformer is plugged into the electrical outlet, a model code and a test number (example: J2.0), begin to flash in the faceplate display . Then, “12:00 PM” and the words “CURRENT TIME" begin to flash. NOTE: If “- - - -” shows in the display , press the r UP or s DOWN button until the model code (“LL4 ...

  • Whirlpool WHES40 - page 13

    13 Pr og r amming the W ater Softener Questions? Call T oll Free 1-866-986-3223 Monday- Friday , 8 AM - 7 PM EST or visit www .ecodynewatertreatment.com When you call, please be prepared to provide the model, date code and serial number , found on the rating decal, typically located on the rim below the salt lid hinges. SET RECHARGE (REGENERA TION) ...

  • Whirlpool WHES40 - page 14

    14 Customizing F ea tur es / Options RECHARGE initiated RECHARGE The RECHARGE button is used to initiate an immedi- ate recharge. 1 . Press and hold the RECHARGE button until the words “RECHARGE", “SERVICE" and “FILL" flash in the display . SET SAL T LEVEL The water softener has a salt monitor indicator light to remind you to a ...

  • Whirlpool WHES40 - page 15

    15 Efficiency Icon In the state of California: Y ou must turn the Salt Efficiency Fea ture ON. This may initiate more frequent recharges. However , it will operate at 4,000 grains per pound of salt or higher . Customizing F ea tur es / Options POWER OUT AGE MEMORY If electrical power to the water softener is lost, “mem- ory'' built into ...

  • Whirlpool WHES40 - page 16

    16 Customizing F ea tur es / Options MAXIMUM DA YS BETWEEN REGENERA- TIONS The water softener automatically controls regenera- tion frequency . This provides the greatest operating efficiency and, under most conditions, this feature should be left in this automatic mode. However , you may modify this feature if you want to force a regen- eration ev ...

  • Whirlpool WHES40 - page 17

    FIG . 32 Broom Handle Pencil Mark 1” - 2” Salt Salt Bridge W ater Level Push T ool into Salt Bridge to Break 17 FIG . 33 Cap O-ring Seal Screen Support Screen Gasket *Flow Plug (HVDC) Housing Ferrule Nut Cone Screen *Flow Plug *Install with lettered side up, concave side down. CLEANING THE NOZZLE & VENTURI A clean nozzle & venturi (See ...

  • Whirlpool WHES40 - page 18

    18 T roubleshooting While an error code appears in the display , all buttons are inoperable except the PROGRAM button. PRO- GRAM remains operational so the service person can perform the Manual Advance Diagnostics, see below , to further isolate the problem. Procedure for removing error code from dis- play: 1 . Unplug transformer from electrical ou ...

  • Whirlpool WHES40 - page 19

    19 T roubleshooting This check verifies proper operation of the valve motor , brine tank fill, brine draw , regeneration flow rates, and other controller functions. Always make the initial checks, and the manual initiated diagnos- tics. NOTE: The electronic control display must show a steady time (not flashing). If an error code shows, first press ...

  • Whirlpool WHES40 - page 20

    20 8 7 6 5 Softener Exploded View 1 2 3 4 5 6 7 8 9 41 40 V alve Assembly See Pages 22 & 23 for part s 10 1 1 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 122 ...

  • Whirlpool WHES40 - page 21

    21 Softener P ar ts List Key No. Part No. Description 1 7170296 O-Ring, 2-7/8” x 3-1/4” 2 7170254 O-Ring, 13/16” x 1-1/16” 3 7077870 T op Distributor 4 7170270 O-Ring, 2-3/4” x 3” 5 7105047 Repl. Bottom Distributor 6 7176292 Clamp Section (2 req.) 7 7088033 Retainer Clip (2 req.) 8 7161849 Repl. Resin T ank, 9” x 40” 9 0502272 Resin ...

  • Whirlpool WHES40 - page 22

    22 V alv e Exploded V iew wear-strip seal cross-section view 100 101 102 103 104 105 106 107 108 109 1 10 1 1 1 1 12 1 13 1 14 1 15 140 1 16 1 17 1 18 1 19 120 121 122 123 124 126 125 127 128 129 130 131 132 133 134 135 136 137 138 139 141 142 143 144 ...

  • Whirlpool WHES40 - page 23

    23 V alv e P ar ts List Key No. Part No. Description 100 7224087 Screw , #8-32 x 1” (2 req.) 101 7286039 Motor (incl. 2 ea. of Key No. 100) 102 7231393 Motor Plate 103 0900857 Screw , #6-20 x 3/8” (3 req.) 104 7171250 Bearing 105 7283489 Cam & Gear 106 7169180 Clip, Drain 107 0900431 Hose Clamp 108 7271270 Drain Hose Adaptor 109 7170288 O-R ...

メーカー Whirlpool カテゴリー Water System

Whirlpool WHES40のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WHES40の取扱説明書
- Whirlpoolの製品カード
- パンフレット
- またはWhirlpool WHES40の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Whirlpool WHES40の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Whirlpool WHES40の取り付け説明書、サービスマニュアル、簡易説明書、またはWhirlpool WHES40のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Whirlpool WHES40の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Whirlpool WHES40デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWhirlpool WHES40を使用するのを助ける技術的文書のことです。説明書は通常、全てのWhirlpool WHES40ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Whirlpoolの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Whirlpool WHES40の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWhirlpool WHES40の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Whirlpool WHES40に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Whirlpool WHES40デバイスの基本機能を使うにあたってのヒント。 Whirlpool WHES40のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Whirlpool WHES40に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWhirlpool WHES40のメーカー/サービスへの連絡先に関する情報。

Whirlpool WHES40についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWhirlpool WHES40の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWhirlpool WHES40で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)