日本語 dropdown-ico

Hearth and Home Technologies QVI-30FB-Sの取扱説明書

40ページ 2.03 mb
ダウンロード

ページに移動 of 40

Summary
  • Hearth and Home Technologies QVI-30FB-S - page 1

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 1 Model(s): QVI-30FB-S • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light any appliance - Do not touch any electrical switch. Do not use any phone in your building. - ...

  • Hearth and Home Technologies QVI-30FB-S - page 2

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 2 Congratulations Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on appliance: ____________________ Dealership purchased from: __________ ...

  • Hearth and Home Technologies QVI-30FB-S - page 3

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 3 T able of Contents 1 Listing and Code Approvals A. Appliance Certi fi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. BTU Speci fi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. High Altitude Installations . . . . . . . . . . . . . . . . . . ...

  • Hearth and Home Technologies QVI-30FB-S - page 4

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 4 Note : T o assure top performance, safety and ef fi ciency , inserts must be installed with an approved fl ue liner as per CAN/CGA B-149 or National Fuel Gas Code ANSI Z223 and these instructions. Not e: This installation must c onform wi th local c odes. In the absenc e of local c odes y ...

  • Hearth and Home Technologies QVI-30FB-S - page 5

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 5 Quadra-Fire gas inserts are designed for recessed installa- tions into solid fuel masonry or factory built non-combustible fi replaces that have been installed in accordance with the National, Provincial, State and local building codes. Prior to installing the gas insert: • Have the chim ...

  • Hearth and Home Technologies QVI-30FB-S - page 6

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 6 3 3 F ireplace Size Requirements Figure 3.1 Fireplace Opening NOTE: For actual appliance dimensions refer to Section 15. B 2 in. 50.8 mm A C TOP VIEW D FRONT VIEW MINIMUM FIREPLACE SIZE Location QVI30FB-S Inches Millimeters A Front Width 30-1/4 768.4 B Rear Width 19 482.6 C Depth 14-1/8 358 ...

  • Hearth and Home Technologies QVI-30FB-S - page 7

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 7 B. Clearances Figure 3.2 Clearances to Mantels or other Combustibles above Appliance Fire Risk. • Locate and install appliance to all clearance speci fi cations in manual. Fire Risk. Odor Risk. • Clearance to combustible material under the insert is 1/4 inch (0.6 cm). • Use leveling ...

  • Hearth and Home Technologies QVI-30FB-S - page 8

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 8 Fire Risk. Asphyxiation Risk. • T erminations MUST meet minimum clearances. • Exhaust gases are hot. • Nearby vents may draw fumes into house. A. V ent T ermination Minimum Clearances Figure 4.1 speci fi es minimum vent heights for various pitched roofs. Roof Pitch H (Min.) Ft. Flat ...

  • Hearth and Home Technologies QVI-30FB-S - page 9

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 9 CAUTION ALL vent speci fi cations MUST be followed. • This product is tested and listed to these speci fi cations. • Appliance performance will suffer if speci fi cations are not followed. Figure 5.1 C. Measuring Standards V ertical measurements listed in the vent diagram (Figure 5.1 ...

  • Hearth and Home Technologies QVI-30FB-S - page 10

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 10 6 6 Installation Preparation Fire Risk. A hearth or hearth extension (if present) must comply with either of the following: • The solid fuel burning fi replace manufacturer’s speci fi cation. • Local building codes required by authority having jurisdiction. • NFPA 211 Prepare the ...

  • Hearth and Home Technologies QVI-30FB-S - page 11

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 11 A. V enting Components 7 7 Installing V ent P ipe and Appliance The vertical vent termination system installed on this model includes: • One 3-foot section stainless steel fl exible pipe (included with insert). • One length of 3-inch fl exible vent pipe for combustion air (included w ...

  • Hearth and Home Technologies QVI-30FB-S - page 12

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 12 Figure 7.2 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY SEALANT ADHESIVE • T rim chimney top plate to minimize excess overhang or bend over fl ue tile (see Figure 7.2). • Place 3/8 inch bead of 300º F silicone on fl ue tile top. C. Placing, Securing and Leveling the Appliance • ...

  • Hearth and Home Technologies QVI-30FB-S - page 13

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 13 D. Installing Adaptor and T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 7.3). T o install adaptor see Figure 7.4. Roof Pitch H (Min.) Ft. Flat to 6/12.................... 1.0* Over 6/12 to 7/12 ........1.25* Over 7/12 to ...

  • Hearth and Home Technologies QVI-30FB-S - page 14

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 14 • Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes. • Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve. • Check all fi ttings and connections of appliance w ...

  • Hearth and Home Technologies QVI-30FB-S - page 15

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 15 Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory . • Changing valve settings may result in fi re hazard or bodily injury . HIGH AL TITUDE INST ALLA TIONS U.L. Listed gas appliances are tested and approved without requiring changes for elevatio ...

  • Hearth and Home Technologies QVI-30FB-S - page 16

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 16 A. Wiring the Appliance 9 9 Elect rical Infor mation Note : This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric Code, CSA C221.1. ON/OFF S ...

  • Hearth and Home Technologies QVI-30FB-S - page 17

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 17 B. Junction Box Installation Figure 9.2 Junction box installation JUNCTION BOX SIDEW ALL FEED PLUG THROUGH HOLE INSERT STRAIN RELIEF AROUND CORD IN THIS END FROM OUTSIDE OF UNIT SCREW PROVIDED Optional Accessories Connecting the electrical junction box is required if using a blower or remo ...

  • Hearth and Home Technologies QVI-30FB-S - page 18

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 18 Figure 9.4 Fan Wiring Diagram NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 105 0 C RA TED WIRE. JUNCTION BOX V ARIABLE SPEED CONTROL TEMPERA TURE SENSOR SWITCH WHT GRN BLK BLK 1 10-120 V AC BLOWER BLOWER RECEPT ACLE BLK BL ...

  • Hearth and Home Technologies QVI-30FB-S - page 19

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 19 A. Mantel Projections Figure 10.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance, not the surround. 1 0 10 Fin ishing Figure 10 .1 Clearances to Mantels or other Comb ...

  • Hearth and Home Technologies QVI-30FB-S - page 20

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 20 Figure 1 1.1 Placement of Embers EMBER MA TERIAL (TOP SURF ACE, AND FRONT) BURNER P AN AIR SHUTTER 1 1 11 Appliance Setup A. Remove Shipping Materials Remove shipping materials from inside or underneath the fi rebox. B. Clean the Appliance Clean/vacuum any sawdust that may have accumulate ...

  • Hearth and Home Technologies QVI-30FB-S - page 21

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 21 E. Positioning the Logs Log Assembly: LOGS-QVI30FB 1 1 6 6 2 2 4 4 7 7 5 5 3 3 Log Placement CAUTION: Logs are fragile! Carefully remove the logs from the packaging. LOG #1 (SR V2020-140): Place log #1 by locating the legs of log over the air de fl ector . The notch or the back side of th ...

  • Hearth and Home Technologies QVI-30FB-S - page 22

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 22 LOG #3 (2020-142): Position log #3 by locating its slot over the tab on the front right of the burner . The slot in the right end of the log slides over grate. Slide log all the way back on tab and grate. LOG #2 (SR V2020-141): Position log #2 by locating its slot over the tab on the front ...

  • Hearth and Home Technologies QVI-30FB-S - page 23

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 23 LOG #6 (SRV340-705): Place log #6 across log #1 and log #5. The notch in the bottom of log #6 rests in the carved out section on top of log #5 and the left end of the log sits in the horizontal carved out section of log #1. LOG #7 (SR V740-707): Place log #7 across logs #1 and #3 in the gr ...

  • Hearth and Home Technologies QVI-30FB-S - page 24

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 24 Figure 1 1.16 Glass Assembly F . Glass Assembly Removing Glass Assembly There are two glass latches on the bottom of glass assembly . • T o release glass assembly , pull latch forward and allow to retract away from glass assembly . • Remove glass assembly after both latches have been r ...

  • Hearth and Home Technologies QVI-30FB-S - page 25

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 25 Fire Risk. Explosion Risk. Gas may build up while lighting pilot. • Remove glass assembly before lighting pilot. • Replace glass assembly after lighting pilot. A. Before Lighting Appliance This appliance has a Standing Pilot Ignition. Before operating this appliance have a qualified te ...

  • Hearth and Home Technologies QVI-30FB-S - page 26

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 26 B. Lighting Appliance Standing Pilot Ignition 1. T urn off all electric power to the appliance if service is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position. 4. Push in gas control knob slightly and turn clock- wise to OFF”. Do not force. 5. Close cont ...

  • Hearth and Home Technologies QVI-30FB-S - page 27

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 27 C. Check Pilot Flame Appearance Pilot fl ame must contact the thermocouple and thermopile for reliable appliance operation. • Pilot fl ame should be as shown in Figure 12.1. D. After Appliance is Lit Initial Break-in Procedure When you light the appliance, you may notice that it pro- d ...

  • Hearth and Home Technologies QVI-30FB-S - page 28

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 28 E. Frequently Asked Questions Fire Risk. High T emperatures. Keep combustible household items away from appliance. Do NOT obstruct combustion and ventilation air . • Do NOT place combustible items on top of or in front of appliance. • Keep furniture, draperies away from appliance. Smok ...

  • Hearth and Home Technologies QVI-30FB-S - page 29

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 29 A. Standing Pilot Ignition System 1 3 13 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service person in the diagnosi ...

  • Hearth and Home Technologies QVI-30FB-S - page 30

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 30 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. Continued c. Defective valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter a the thermopile terminals. The millivolt meter should read greater than 125 ...

  • Hearth and Home Technologies QVI-30FB-S - page 31

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 31 1 4 14 Maintaining and Ser vicing Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a quali fi ed service technician should perform an appliance checkup at the beginning of each heating season. Annual inspection by qua ...

  • Hearth and Home Technologies QVI-30FB-S - page 32

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 32 Inspect Maintenance T asks Doors, Surrounds and Fronts 1. Assess condition of screen and replace as necessary . Recommend addition of screen if one is not present. 2. Inspect for scratches, dents or other damage and repair as necessary . 3. V erify no obstructions to air fl ow through the ...

  • Hearth and Home Technologies QVI-30FB-S - page 33

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 33 Figure 15.1 Appliance Dimensions D F E H G ELECTRICAL ACCESS (IF EQUIPPED) GAS INLET C A B 2-1/16 in. 52 mm 1-9/16 in. 40 mm 3-9/16 in. 91 mm 1-1/16 in. 28 mm 2-1/2 in. 64 mm 4 in. 102 mm 13-3/4 in. 350 mm 3-1/8 in. 80 mm 6-5/8 in. 169 mm Tw o ø 2-13/16 in. 71 mm 9-9/16 in. 142 mm REF 1 5 ...

  • Hearth and Home Technologies QVI-30FB-S - page 34

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 34 B. V ent Kits Components Direct V ent Flex Liner Kits (see Figure 15.2) LINK-DV -30B or (LINK-DV -30): Masonry 3 inch fl ex liner kit. Expands to 30 feet. Includes: two liners, termination cap, fl ashing, and link adapter . LINK-DV4-30B or (LINK-DV4-30): Masonry 3 inch fl ex liner kit. ...

  • Hearth and Home Technologies QVI-30FB-S - page 35

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 35 Service Parts Diagram QVI-30FB-S R C. Service Parts Beginning Manufacturing Date: Oct. 2007 Ending Manufacturing Date:_____ Part number list on following page. Log Set Assembly 4 1 6 2 7 3 5 8 9 10 11 12 13 14 ...

  • Hearth and Home Technologies QVI-30FB-S - page 36

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 36 QVI-30FB-S Service Parts List IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTI ...

  • Hearth and Home Technologies QVI-30FB-S - page 37

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 37 Service Parts Diagram QVI-30FB-S R C. Service Parts Beginning Manufacturing Date: Oct. 2007 Ending Manufacturing Date:______ IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts l ...

  • Hearth and Home Technologies QVI-30FB-S - page 38

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 38 D. Limited Lifetime W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in th ...

  • Hearth and Home Technologies QVI-30FB-S - page 39

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 39 D. Limited Lifetime W arranty (continued) • This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or co ...

  • Hearth and Home Technologies QVI-30FB-S - page 40

    Quadra-Fire • QVI-30FB-S • 2020-910 Rev . F • 9/08 40 Quadra-Fire, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www .quadra fi re.com E. Contact Information Please contact your Quadra-Fire dealer with any questions or concerns. For the location of your nearest Quadra-Fire dealer , please vis ...

メーカー Hearth and Home Technologies カテゴリー Indoor Fireplace

Hearth and Home Technologies QVI-30FB-Sのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- QVI-30FB-Sの取扱説明書
- Hearth and Home Technologiesの製品カード
- パンフレット
- またはHearth and Home Technologies QVI-30FB-Sの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Hearth and Home Technologies QVI-30FB-Sの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Hearth and Home Technologies QVI-30FB-Sの取り付け説明書、サービスマニュアル、簡易説明書、またはHearth and Home Technologies QVI-30FB-Sのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Hearth and Home Technologies QVI-30FB-Sの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Hearth and Home Technologies QVI-30FB-Sデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHearth and Home Technologies QVI-30FB-Sを使用するのを助ける技術的文書のことです。説明書は通常、全てのHearth and Home Technologies QVI-30FB-Sユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Hearth and Home Technologiesの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Hearth and Home Technologies QVI-30FB-Sの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHearth and Home Technologies QVI-30FB-Sの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Hearth and Home Technologies QVI-30FB-Sに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Hearth and Home Technologies QVI-30FB-Sデバイスの基本機能を使うにあたってのヒント。 Hearth and Home Technologies QVI-30FB-Sのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Hearth and Home Technologies QVI-30FB-Sに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHearth and Home Technologies QVI-30FB-Sのメーカー/サービスへの連絡先に関する情報。

Hearth and Home Technologies QVI-30FB-Sについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもHearth and Home Technologies QVI-30FB-Sの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHearth and Home Technologies QVI-30FB-Sで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)