-
Jet JWCS-10 - page 1
Owner's Manual XACTA ® Fence II Homeshop 30/52 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708928Z Ph.: 800-274-6848 Revision B 03/06 www.wmhtoolgroup.com Copyright © WMH Tool Group This Manual is Bookmarked ...
-
Jet JWCS-10 - page 2
2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers lo cated throughout the United States can giv e you qu ick service. In most cases, any of these WMH Tool Group Authorized Servic e Centers can authorize warranty repair, assist you in obtai ...
-
Jet JWCS-10 - page 3
3 Table of Contents WARRANTY A ND SERVICE ........................................................................................................... ............. 2 Table of Contents .............................................................................................................. ............................ 3 Warnings ............... ...
-
Jet JWCS-10 - page 4
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Rea d and understand the warnings posted on the mach ine and in this manual. Failure to comply with all of these warnings may cause seri ous injury. 3. Replace the warning labels if they become obscu red or removed. 4. The Table Saw on which the ...
-
Jet JWCS-10 - page 5
5 21. Keep visitors a safe distance from the work area. Keep children away. 22. Make your workshop child proof with padlocks , master switch es or by removing starter keys. 23. Give your work undivided attention. Looking ar ound, carrying on a conversatio n and “horse-play” are careless acts that can result in serious inj ury. 24. Maintain a ba ...
-
Jet JWCS-10 - page 6
6 Unpacking Open shipping carton s and check that all parts are intact. Report any damage immediately to your distributor. Read the instruction manu al thoroughly for assembly, alignment, and ma intenance instructions. Contents of the Shipping Containers Box One: 1 XACTA Fence II 1 Lock Lever Knob Box Two: 1 Front Rail 1 Back Rail 1 Guide Tube 3 Bl ...
-
Jet JWCS-10 - page 7
7 Installation Tools required Drill with 5/16" drill bit 10mm open end wrenches Cross point screwd river Adjustable square Hammer (or rubber mallet) Straight edge The following instructions are for in stalling the XACTA Fence II and Rail System on JET Models JWCS-10 and JWTS-10 series table saws. Front Rail Installation Referring to Figures 1: ...
-
Jet JWCS-10 - page 8
8 Back Rail Installation 1. Locate the back rail which is 1-1/2" x 1-1/2" with holes running along one si de only. The height of the back rail when atta ched to the saw is not critical. 2. Align the holes in the back rail to the holes in the table top, as shown in Figure 4. 3. Secure the back rail to the holes in the saw table with four 1 ...
-
Jet JWCS-10 - page 9
9 3. Tap down the extension table at various points along its edge where it meets the saw table, until it is level with the saw table (Figure 7). As one part of the edge becomes level with the table, tighten the clamp on that side. Then move to the other side and re peat, until the full length of the edge is level with the saw table. Lay a straight ...
-
Jet JWCS-10 - page 10
10 Guide Tube Referring to Figure 11: The guide tube (A) is placed on to p of the front rail (B) and is mounted with t he scale facing toward the operator. 1. Align the holes in the bottom of the guide tube (A) with the holes in the front rail (B). 2. Fasten the guide tube (A) to the rail (B) from beneath with 1/4-20 x 3/4 hex cap screws (C), 1/4 l ...
-
Jet JWCS-10 - page 11
11 Fence Adjustments Note: Fence adjustments should be perform ed in the order given. Leveling Fence to the Saw Table 1. Place the fence on the table and lock it. 2. View the fence from the left side of the saw (Figure 14). Look for the spa ce between the table and the fence bottom to be equal along the entire length of the fence (A, B, Fig. 14). I ...
-
Jet JWCS-10 - page 12
12 90 ° to the Table Adjustment 1. Place the fence on the saw table and lock it. 2. Place a square (A, Fig. 17) on the table next to the fence. The fence should b e 90 ° to the table. 3. If adjustment is necessary, unlock the fence, and turn one of the two nylon adjustment screws (B, Fig. 17) until the fence is 90 ° to the table. 4. Lock the fen ...
-
Jet JWCS-10 - page 13
13 Parts Ordering Replacement Parts To order parts or reach our se rvice department, call 1-800 -274-6848 between 7:30 a.m. and 5:30 p.m. (CST), Monday through F riday. Having the Model Number and S erial Number o f your machine available when you call will allow us to serve you quickly and accurately. Parts for XACTA Fence II Homeshop 30/52 Fence ...
-
Jet JWCS-10 - page 14
14 Parts for XACTA Fence II Homeshop 30/52 Rail Assembly Index No. Part No. Description Size Qty 1 ............... HF2-201 ................... Front Fence Rail - Standard................................. ......................... ........... 1 ................. HF2-201A................. Front Fence Rail - Long Table ............................. .. ...
-
Jet JWCS-10 - page 15
15 Parts for the XACTA Fence II Homeshop 30/52 Leg Assembly Index No. Part No. Description Size Qty 1 ............... XF2-301 ................... Leg ....................................................................... .................................... 2 2 ............... TS-0561031 ............. Hex Nut ...................................... ...
-
Jet JWCS-10 - page 16
16 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.co m ...
Jet JWCS-10についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもJet JWCS-10の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJet JWCS-10で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。