Delta SH100の取扱説明書

18ページ 0.89 mb
ダウンロード

ページに移動 of 18

Summary
  • Delta SH100 - page 1

    INSTRUCTION MANUAL Router / Shaper (Model SH100) P ART NO. 905582 - 05-15-02 Copyright © 2002 Delta Machinery ESP AÑOL: PÁGINA 19 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta SH100 - page 2

    2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precaut ...

  • Delta SH100 - page 3

    3 ADDITIONAL SAFETY RULES FOR FOR THE ROUTER/SHAPER WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y Fig. B 21. USE A HEA VY WORKPIECE when shaping with starting pin and collar(s). DO NOT SHAPE a short, light workpiece against the collar(s) (Figs. D and E). Fig. D Fig. E Fig. F SUFFICIENT BEARING SURF ACE CUTTER COLL ...

  • Delta SH100 - page 4

    4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wir e and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wir e extension cords which have 3- prong gr ounding type plugs and matching r eceptacle which will accept the machine’ s ...

  • Delta SH100 - page 5

    Use proper extension cor ds. Make sur e your extension cord is in good condition and is a 3-wir e extension cor d which has a 3-prong gr ounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the curr ent of the machine. An undersized cord will caus ...

  • Delta SH100 - page 6

    6 ROUTER / SHAPER P ARTS Fig. 2 1. Router / Shaper 2. 1¼" Open End Arbor Wr ench 3. Collet Wr ench 4. 3mm Hex wrench 5. Left Hand Fence Body 6. Right Hand Fence Assembly 7. Spindle Knob 8. Fence Knob (2) 9. Cutter Guard Bracket 10. T emplate Guide Insert 11. W ooden Fence (2) 12. 1/2" Collet with Nut 13. 1/4" Adapter 14. Foot (4) 15 ...

  • Delta SH100 - page 7

    7 ASSEMBL Y WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED. DO NOT OPERA TE THIS MACHINE UNTIL YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL OVERHEAD CUTTER GUARD BRACKET Assemble the overhead cutter guard holding bracket (A) Fig. 6, to the rear of the Router/Shaper ...

  • Delta SH100 - page 8

    8 Fig. 10 P S A H FENCE ASSEMBL Y AND DUST CHUTE T wo fence halves are supplied as standard equipment with the Router/Shaper . T o assemble and install the fence assembly , pr oceed as follows: 1. NOTE: The fence body with the see-thru cutter guard (R) Fig. 7, assembled to it, is to be assembled to the right hand side of the table, when facing the ...

  • Delta SH100 - page 9

    9 ASSEMBLING T ABLE INSER T The table insert (A) is assembled in the table, as shown in Fig. 11. Fig. 11 F ASTENING ROUTER/SHAPER TO SUPPOR TING SURF ACE IF DURING OPERA TION THERE IS ANY TENDENCY FOR THE ROUTER/SHAPER TO TIP OVER, SLIDE OR WALK ON THE SUPPOR TING SURF ACE, THE ROUTER/SHAPER SHOULD BE SECURED TO THE SUPPORTING SURF ACE. REMOVE THE ...

  • Delta SH100 - page 10

    10 OVERLOAD PROTECTION The Router/Shaper is equipped with overload protection. If the motor shuts off, or fails to start due to overloading (cutting stock too fast; using dull bits and cutters; using the machine beyond its capacity or at low voltage, etc.), TURN THE SWITCH (A) FIG. 16, TO THE “OFF” POSITION . Let the motor cool three to five mi ...

  • Delta SH100 - page 11

    11 Fig. 20 Fig. 21 A A Fig. 22 A B Fig. 23 C A B SEE-THRU CUTTER GUARD The see-through cutter guar d (A) Fig. 20, should always be used when using the fence to guide the work. The guard (A) raises as the workpiece is pushed along the fence and lowers at the completion of the cut. The guard (A) can be moved up and out of the way as shown in Fig. 21, ...

  • Delta SH100 - page 12

    12 5. Loosen adjustment bolt (D) Fig. 24, and corresponding bolt at the r ear of the machine (not shown.). 6. Carefully move the spindle height lock knob (E) Fig. 24, up or down until the metal rod (A) is 90 degr ees to the table surface. Then tighten adjustment bolts (D) which were loosened in STEP 5 . Fig. 24 A E D Fig. 25 Fig. 26 E E C A B A G F ...

  • Delta SH100 - page 13

    13 Fig. 27 Fig. 28 Fig. 29 Fig. 30 A D C H E F G A B B A A K B INST ALLING ROUTER BITS 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Raise spindle to the maximum height and tighten lock knob. 3. This machine is supplied with a 1/2 inch collet (A) Fig. 27, that accepts 1/2 inch shank router bits. A 1/4 inch adapter sleeve (B) Fig. 28, is also furnishe ...

  • Delta SH100 - page 14

    14 INST ALLING OVERHEAD CUTTER GUARD An overhead cutter guard, shown in Fig. 31, is supplied as standard equipment with your Router/Shaper and should always be used for operations that requir e the fence to be removed. T o install the overhead cutter guard, pr oceed as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove the fence assembly f ...

  • Delta SH100 - page 15

    15 OPERA TION The following is an example of the setting-up and operational procedur es when using the fence, collars and starting pin. Please review this information car efully befor e turning on the power to avoid damage to the machine or personal injury . WARNING: The use of accessories and attachments not recommended by Delta may result in risk ...

  • Delta SH100 - page 16

    16 POSITION OF COLLARS 1. The collars may be used in any of the following po- sitions: above, below or between two cutters. 2. When the collar is used below the cutter , as shown in Fig. 43, the progr ess of the cut can be observed at all times. However , any accidental lifting of the work will gouge the wood and ruin the workpiece. 3. When the col ...

  • Delta SH100 - page 17

    17 NOTES ...

  • Delta SH100 - page 18

    T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized service station with pr ...

メーカー Delta カテゴリー Router

Delta SH100のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SH100の取扱説明書
- Deltaの製品カード
- パンフレット
- またはDelta SH100の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Delta SH100の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Delta SH100の取り付け説明書、サービスマニュアル、簡易説明書、またはDelta SH100のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Delta SH100の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Delta SH100デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDelta SH100を使用するのを助ける技術的文書のことです。説明書は通常、全てのDelta SH100ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Deltaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Delta SH100の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDelta SH100の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Delta SH100に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Delta SH100デバイスの基本機能を使うにあたってのヒント。 Delta SH100のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Delta SH100に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDelta SH100のメーカー/サービスへの連絡先に関する情報。

Delta SH100についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDelta SH100の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta SH100で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)