NETGEAR GS110TP-100NASの取扱説明書

32ページ 0.56 mb
ダウンロード

ページに移動 of 32

Summary
  • NETGEAR GS110TP-100NAS - page 1

    202-10596-01 March 2010 v1.0 NETGEAR , Inc. 350 East Plumeria Drive San Jose, California 95134 USA GS110TP Hardware Installation Guide ...

  • NETGEAR GS110TP-100NAS - page 2

    ii v1.0, March 2010 © 2010 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR, the NETGEAR logo, and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respect ...

  • NETGEAR GS110TP-100NAS - page 3

    Contents iii v1.0, March 2010 Contents GS110TP Hardware Installation Guide About This Manual Conventions, Formats, and Scope .................................................................................... v How to Print this Manual ................................................................................................... vi Revision H ...

  • NETGEAR GS110TP-100NAS - page 4

    iv Contents v1.0, March 2010 Chapter 4 Installation Step 1: Preparing the Site .............................................................................................. 4-1 Step 2: Installing the Switch ........................................................................................... 4-2 Installing the Switch on a Flat Surface ...... ...

  • NETGEAR GS110TP-100NAS - page 5

    v v1.0, March 2010 About This Manual The NETGEAR ® ProSafe TM GS110TP Hardware Installation Guide describes how to install and power on the GS110TP Smart PoE Switch. The information in this manual is intended for readers with intermediate computer and Internet skills. Conventions, Formats, and Scope The conventions, formats, and scope of this manu ...

  • NETGEAR GS110TP-100NAS - page 6

    Danger: This is a safety warning. Failure to take heed of this notice may result in personal injury or death. GS110TP Hardware Installation Guide vi About This Manual v1.0, March 2010 • Scope. This manual is written for the GS110TP Smart PoE Switch according to these specifications: Product Version GS110TP Smart PoE Switch Manual Publication Date ...

  • NETGEAR GS110TP-100NAS - page 7

    1-1 v1.0, March 2010 Chapter 1 Introduction Congratulations on the purchase of your NETGEAR GS110TP Smart PoE Switch. The GS110TP Smart PoE Switch is a supplement to the Gigabit Advanced Smart Switch family. Available as a desktop or wall-mountable switch, the GS110TP Smart PoE Switch is not intended to be rack- mountable. The GS110TP is a PoE-supp ...

  • NETGEAR GS110TP-100NAS - page 8

    GS110TP Hardware Installation Guide 1-2 Introduction v1.0, March 2010 The GS110TP Smart PoE Switch is a free-standing switch. It is IEEE-compliant and offers low latency for high-speed networking. All ports can automatically negotiate to the highest speed. This capability makes the switch ideal for environments that have a mix of Ethernet, Fast Eth ...

  • NETGEAR GS110TP-100NAS - page 9

    GS110TP Hardware Installation Guide Introduction 1-3 v1.0, March 2010 • Standard NETGEAR 1xx series chassis. • NETGEAR Green product features. • External 48V/1.25A PA. PoE Features The GS110TP Smart PoE Switch supports IEEE 802.3af PSE features: • Ports 1 through 8 support IEEE 802.3af, Alternative A (MDI-X). • PoE is enabled by default. ...

  • NETGEAR GS110TP-100NAS - page 10

    GS110TP Hardware Installation Guide 1-4 Introduction v1.0, March 2010 Package Contents Figure 1-1 shows the package contents of the NETGEAR GS110TP Smart PoE Switch. Figure 1-1 Verify that the package contains the following: • NETGEAR GS110TP Smart PoE Switch • Rubber footpads for tabletop installation • Wall mounting screws (2) • External ...

  • NETGEAR GS110TP-100NAS - page 11

    2-1 v1.0, March 2010 Chapter 2 Physical Description This chapter describes the NETGEAR GS110TP Smart PoE Switch hardware features. Topics include: • GS110TP Front and Back Panel Configuration • LED Designations • Device Hardware Interfaces GS110TP Front and Back Panel Configuration The GS110TP Smart PoE Switch has eight 10/100/1000 Mbps autos ...

  • NETGEAR GS110TP-100NAS - page 12

    GS110TP Hardware Installation Guide 2-2 Physical Description v1.0, March 2010 • Power and Status LED • PoE Max LED Figure 2-2 illustrates the NETGEAR GS110TP Smart PoE Switch back panel. Power Connector Figure 2-2 The back panel contains the following: • A DC input for the supplied 48V/1.25A external power adapter LED Designations Port LEDs T ...

  • NETGEAR GS110TP-100NAS - page 13

    GS110TP Hardware Installation Guide Physical Description 2-3 v1.0, March 2010 System LEDs The following table describes the system LED designations. Table 2-2. System LEDs LED Designation Power/Status LED • Solid Green = Power is supplied to the switch and the switch is operating normally. • Solid Yellow = The switch is booting. • Off = Power ...

  • NETGEAR GS110TP-100NAS - page 14

    GS110TP Hardware Installation Guide 2-4 Physical Description v1.0, March 2010 To simplify the procedure for attaching devices, all RJ-45 ports support Auto Uplink. This technology allows attaching devices to the RJ-45 ports with either straight-through or crossover cables. When inserting a cable into the switch’s RJ-45 port, the switch automatica ...

  • NETGEAR GS110TP-100NAS - page 15

    3-1 v1.0, March 2010 Chapter 3 Applications Your NETGEAR GS110TP Smart PoE Switch is designed to provide flexibility in configuring your network connections. It can be used as a stand-alone device or with 10 Mbps, 100 Mbps, and 1000 Mbps hubs and switches. Desktop Switching The GS110TP Smart PoE Switch can be used as a desktop switch to build a sma ...

  • NETGEAR GS110TP-100NAS - page 16

    GS110TP Hardware Installation Guide 3-2 Applications v1.0, March 2010 ...

  • NETGEAR GS110TP-100NAS - page 17

    4-1 v1.0, March 2010 Chapter 4 Installation This chapter describes the installation procedures for your NETGEAR GS110TP Smart PoE Switch. Switch installation involves the following steps: Step 1: Preparing the Site Step 2: Installing the Switch Step 3: Checking the Installation Step 4: Connecting Devices to the Switch Step 5: Applying AC Power Step ...

  • NETGEAR GS110TP-100NAS - page 18

    GS110TP Hardware Installation Guide 4-2 Installation v1.0, March 2010 Step 2: Installing the Switch The GS110TP Smart PoE Switch can be used on a flat surface or mounted on the wall. Installing the Switch on a Flat Surface The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the four concave spaces on the bo ...

  • NETGEAR GS110TP-100NAS - page 19

    GS110TP Hardware Installation Guide Installation 4-3 v1.0, March 2010 Step 3: Checking the Installation Before applying power to the switch, perform the following: • Inspect the equipment thoroughly. • Verify that all cables are installed correctly. • Check cable routing to make sure cables are not damaged or creating a safety hazard. • Ens ...

  • NETGEAR GS110TP-100NAS - page 20

    GS110TP Hardware Installation Guide 4-4 Installation v1.0, March 2010 Connect each PC to an RJ-45 network port on the Switch front panel ( Figure 4-1 ). Use Category 5 (Cat5) Unshielded Twisted-Pair (UTP) cable terminated with an RJ-45 connector to make these connections. Note: Ethernet specifications limit the cable length between the switch and t ...

  • NETGEAR GS110TP-100NAS - page 21

    Note: When the device powers up, there is a default IP address already configured on the device. The default IP address is 192.168.0.239 and subnet mask 255.255.255.0. GS110TP Hardware Installation Guide Installation 4-5 v1.0, March 2010 ...

  • NETGEAR GS110TP-100NAS - page 22

    GS110TP Hardware Installation Guide 4-6 Installation v1.0, March 2010 ...

  • NETGEAR GS110TP-100NAS - page 23

    Troubleshooting A-1 v1.0, March 2010 Appendix A Troubleshooting This chapter provides information about troubleshooting the NETGEAR Smart Switch. Topics include the following: • Troubleshooting Chart • Additional Troubleshooting Suggestions Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems. Tab ...

  • NETGEAR GS110TP-100NAS - page 24

    GS110TP Hardware Installation Guide A-2 Troubleshooting v1.0, March 2010 Additional Troubleshooting Suggestions If the suggestions in Troubleshooting Chart do not resolve the problem, refer to the troubleshooting suggestions in this section. Network Adapter Cards Ensure the network adapter cards installed in the PCs are in working condition and the ...

  • NETGEAR GS110TP-100NAS - page 25

    GS110TP Hardware Installation Guide Troubleshooting A-3 v1.0, March 2010 Auto-Negotiation The RJ-45 ports negotiate the correct duplex mode and speed if the device at the other end of the link supports auto negotiation. If the device does not support auto negotiation, the switch only determines the speed correctly and the duplex mode defaults to ha ...

  • NETGEAR GS110TP-100NAS - page 26

    GS110TP Hardware Installation Guide A-4 Troubleshooting v1.0, March 2010 ...

  • NETGEAR GS110TP-100NAS - page 27

    Technical Specifications B-1 v1.0, March 2010 Appendix B Technical Specifications Network Protocol and Standards Compatibility IEEE 802.3i 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x flow control IEEE 802.3z 1000BASE-X IEEE 802.3af DTE Power via MDI Management Windows 2000 + XP, Vista; Microsoft Explorer 6.0 or higher IEEE 8 ...

  • NETGEAR GS110TP-100NAS - page 28

    GS110TP Hardware Installation Guide B-2 Technical Specifications v1.0, March 2010 Interface Eight RJ-45 connectors for 10BASE-T, 100BASE-TX, and 1000BASE-T (Auto Uplink™ on all ports) Two SFP slots for SFP modules LEDs Per RJ-45 port: Speed/Link/Activity Per SFP port: SFP indicator Performance Specifications Forwarding modes: Store-and-forward Ba ...

  • NETGEAR GS110TP-100NAS - page 29

    GS110TP Hardware Installation Guide Technical Specifications B-3 v1.0, March 2010 Electromagnetic Emissions FCC Class B CE Class B: Includes EN55022 (CISPR 22), 55024, and 50082-1 VCCI Class B C-Tick Safety UL/cUL (UL 1950)/cUL IEC950/EN60950) CE (includes EN60950) IEC950 CB ...

  • NETGEAR GS110TP-100NAS - page 30

    GS110TP Hardware Installation Guide B-4 Technical Specifications v1.0, March 2010 ...

  • NETGEAR GS110TP-100NAS - page 31

    Index-1 v1.0, March 2010 Index Numerics 1U 1-3 8-pin 2-3 A Applying AC Power 4-4 Auto Uplink 2-4 Auto-negotiating 1-2 Autosensing 1-2 , 2-3 B Backpressure 1-2 C Category 5 Unshielded Twisted-Pair 1-2 Checking the Installation 4-3 Class of Service 1-1 Connecting Devices to the Switch 4-3 Copper 1-1 Crossover 2-4 D Default IP Address 4-5 Default Rese ...

  • NETGEAR GS110TP-100NAS - page 32

    GS110TP Hardware Installation Guide Index-2 v1.0, March 2010 O Operating Conditions 4-2 Operating Environment 4-1 Operating humidity 4-2 Overview 1-1 P Package Contents 1-4 Pause Frame Flow Control 1-2 Port LEDs 2-2 Power cord 1-4 Preparing the Site 4-1 R Rack-mount Kit 1-4 Reset Button 2-1 RJ-45 1-2 RJ-45 Ports 2-2 Rubber footpads 1-4 , 4-2 S Site ...

メーカー NETGEAR カテゴリー Switch

NETGEAR GS110TP-100NASのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- GS110TP-100NASの取扱説明書
- NETGEARの製品カード
- パンフレット
- またはNETGEAR GS110TP-100NASの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、NETGEAR GS110TP-100NASの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、NETGEAR GS110TP-100NASの取り付け説明書、サービスマニュアル、簡易説明書、またはNETGEAR GS110TP-100NASのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、NETGEAR GS110TP-100NASの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

NETGEAR GS110TP-100NASデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがNETGEAR GS110TP-100NASを使用するのを助ける技術的文書のことです。説明書は通常、全てのNETGEAR GS110TP-100NASユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

NETGEARの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. NETGEAR GS110TP-100NASの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははNETGEAR GS110TP-100NASの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。NETGEAR GS110TP-100NASに関してこのドキュメントで見つけることができる全てのヒントの目次
3. NETGEAR GS110TP-100NASデバイスの基本機能を使うにあたってのヒント。 NETGEAR GS110TP-100NASのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。NETGEAR GS110TP-100NASに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるNETGEAR GS110TP-100NASのメーカー/サービスへの連絡先に関する情報。

NETGEAR GS110TP-100NASについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもNETGEAR GS110TP-100NASの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがNETGEAR GS110TP-100NASで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (1)

Aslan

как отключить PoE GS110tp netgear v2 proSafe