Porter-Cable 698の取扱説明書

19ページ 0.17 mb
ダウンロード

ページに移動 of 19

Summary
  • Porter-Cable 698 - page 1

    Router/Shaper and Shaper T able Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. __________________________________ Type _______________________________________ Serial No. ___________________________________ IMPORTANT Ple ...

  • Porter-Cable 698 - page 2

    2 SAFETY INSTRUCTIONS GROUNDING INSTRUCTIONS This tool should be grounded while in use to protect the operator from electric shock. The tool is equipped with an approved three-conductor cord and three- prong grounding type plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. ...

  • Porter-Cable 698 - page 3

    3 IMPORT ANT SAFETY INSTRUCTIONS WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following: READ AND FOLLOW ALL INSTRUCTIONS. There are certain applications for which this tool was designed. Porter-Cable strongly recommends that this ...

  • Porter-Cable 698 - page 4

    4 1 3 . DON T OVERREACH. Keep proper footing and balance at all times. 1 4 . MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords period ...

  • Porter-Cable 698 - page 5

    5 6 . NEVER RUN STOCK between fence and cutter. 7 . WHEN SHAPING with piloted bit, the pilot must have sufficient bearing surface ( 1 … 8 " minimum) as shown in Fig. 1. Fig. 2 illustrates the INCORRECT method for this operation as the pilot DOES NOT have sufficient bearing surface. 8 . WHEN SHAPING, the work must be fairly heavy in proportio ...

  • Porter-Cable 698 - page 6

    6 CAUTION: D o not operate your tool on a current on which the voltage is not within correct limits. Do not operate tools rated A.C. only on D.C. current. To do so may seriously damage the tool. EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss ...

  • Porter-Cable 698 - page 7

    7 4 . Mount the router base (see Fig. 6 for non-plunge routers, or Fig. 7 for plunge routers), to the underside of the table using screws from the hardware package (routers with less than 2 horsepower use three #10-24 x 3 … 4 " long screws, routers with more than 2 horsepower except Model 7529 use four 5 … 16 "-18 x 1 1 … 4 " s ...

  • Porter-Cable 698 - page 8

    8 . Assemble the left hand (out-feed) fence bracket (B) Fig. 9, to the table in a similiar fashion. 9 . Position the wooden fences to the fence brackets (see Fig. 10), and secure using one, 3 … 8 "-16 x 1 1 … 5 " bolt and matching nut, through each fence and fence bracket. F ASTENING ROUTER/SHAPER T O WORK BENCH The Router/Shaper shou ...

  • Porter-Cable 698 - page 9

    9 INST ALLING AND REMOVING BIT 1 . CAUTION: DISCONNECT MACHINE FROM POWER SOURCE. 2 . Clean and insert shank of bit into collect until shank bottoms. Then back it out approximately 1 … 16 " . 3 . Place chuck wrench (A) Fig. 11, through opening in rear of base and engage flats of chuck. 4 . Move chuck wrench (A) Fig. 11, to the left side of b ...

  • Porter-Cable 698 - page 10

    10 PLUNGE ROUTER MODEL 7538 OR 7539 1 . Move the plunge locking lever (on the router), to the released position. 2 . Rotate Model 75300 Height Adjustment Knob to raise or lower cutter to the desired position. 3 . Release plunge locking lever and push lever to the locked position. ADJUSTING THE FENCE Each fence may be adjusted individually for front ...

  • Porter-Cable 698 - page 11

    11 CONNECTING T O POWER SOURCE CAUTION: Before connecting to power source ALWAYS MAKE SURE THE SWITCH IS IN THE OFF POSITION and that the power circuit is the same as that shown on the specification plate of the Router/Shaper. 1 . Plug the motor cord into the short cord extending from the table switch box. 2 . Turn the router motor switch ON motor ...

  • Porter-Cable 698 - page 12

    12 USING THE ROUTER/SHAPER WARNING: Figures 17 and 20 through 27 show machine with cutter guards removed for clarity. NEVER OPERATE Router/Shaper without guards in place. IMPORTANT: Before using your machine, consider the kind and total amount of rnaterial to be removed. Depending on the material, it may be necessary to make more than one cut to av ...

  • Porter-Cable 698 - page 13

    13 When using piloted bits only part of the edge of the workpiece can be cut since it is necessary to have the other part riding against the pilot. WARNING: Never leave less than 1 … 8 " of the workpiece to ride against the pilot. Leaving less than 1 … 8 " could cause the edge to splinter possibly resulting in serious injury. Adjust t ...

  • Porter-Cable 698 - page 14

    14 SHAPING WITH FENCE When shaping straight edges, the fence can be used as a guide. The entire fence assembly or either the infeed or outfeed section can be adjusted independently as outlined under Adjusting the Fence . For normal work where a portion of the original edge of the work is not altered by the cutter, both the front and rear fences are ...

  • Porter-Cable 698 - page 15

    15 END SHAPING Sufficient support of the work piece must be maintained during all shaping operations. This exists when the workpiece is long enough to rest firmly against both the infeed and outfeed fences when you are halfway through the cut. When end shaping a workpiece that is not long enough to be sufficiently supported halfway through the cut, ...

  • Porter-Cable 698 - page 16

    16 SHAPING NARROW MA TERIAL When shaping narrow material (less than 3" wide) a support as shown in Fig. 27 must be clamped to your Router/Shaper and the workpiece fed under this support with a push stick. The push stick should be slightly narrower and thinner than the workpiece. WARNING: Shaping narrow material without proper support and push ...

  • Porter-Cable 698 - page 17

    17 BRUSH INSPECTION At approximately 100 hours of use, take or send your tool to your nearest Authorized Porter-Cable Service Station to be thoroughly cleaned and inspected; worn parts replaced, when necessary; relubricated with fresh lubricant, if required; reassembled with new brushes; and performance tested. Any loss of power before the above ma ...

  • Porter-Cable 698 - page 18

    18 PORTER-CABLE LIMITED ONE YEAR W ARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace, at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material ...

  • Porter-Cable 698 - page 19

    The following are trademarks of PORTER-CABLE Corporation (Las siguientes son marcas registradas de PORTER-CABLE S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE Corporation): PORTER-CABLE fi , OMNIJIG fi , POCKET CUTTER fi , PORTA- BAND fi , PORTA-PLANE fi , QUICKSAND fi , VERSA-PLANE fi , SANDTRAP fi , SAW BOS ...

メーカー Porter-Cable カテゴリー Router

Porter-Cable 698のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 698の取扱説明書
- Porter-Cableの製品カード
- パンフレット
- またはPorter-Cable 698の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Porter-Cable 698の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Porter-Cable 698の取り付け説明書、サービスマニュアル、簡易説明書、またはPorter-Cable 698のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Porter-Cable 698の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Porter-Cable 698デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPorter-Cable 698を使用するのを助ける技術的文書のことです。説明書は通常、全てのPorter-Cable 698ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Porter-Cableの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Porter-Cable 698の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPorter-Cable 698の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Porter-Cable 698に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Porter-Cable 698デバイスの基本機能を使うにあたってのヒント。 Porter-Cable 698のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Porter-Cable 698に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPorter-Cable 698のメーカー/サービスへの連絡先に関する情報。

Porter-Cable 698についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPorter-Cable 698の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable 698で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)