日本語 dropdown-ico

Lucent Technologies LA41CFの取扱説明書

20ページ 0.29 mb
ダウンロード

ページに移動 of 20

Summary
  • Lucent Technologies LA41CF - page 1

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 1 41" Wood Burning Fireplaces P/N 504,217M REV. D 12/2003 LA41CF LA41TCF MODELS WH Report No. J20017261-231 ELITE SERIES This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and under- stand these instructions befo ...

  • Lucent Technologies LA41CF - page 2

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 2 TABLE OF CONTENTS Safety Rules .................................... page 2 Tools and Building Supplies ............ page 2 Precautions ..................................... page 3 Introduction ..................................... page 3 Clearances/Height Requirements ..... page 3 Chimney System .. ...

  • Lucent Technologies LA41CF - page 3

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 3 Figure 1 TYPICAL INSTALLATION *Construction Materials: • framing materials • paneling • particle board • flooring • millboard • dry wall • plywood • etc. PRECAUTIONS Note: These fireplace systems are not difficult to install. However, in the interest of safety, it is recommended tha ...

  • Lucent Technologies LA41CF - page 4

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 4 WARNING: IF INSULATION IS USED, THE FIREPLACE MUST NOT BE PLACED DI- RECTLY AGAINST IT. INSULATION OR VAPOR BARRIERS, IF USED, MUST FIRST BE COVERED WITH GYPSUM BOARD, PLYWOOD, PARTICLE BOARD OR OTHER MATERIAL TO ASSURE INSULATION AND VAPOR BARRIERS REMAIN IN PLACE. Figure 2 Chimney Height The tota ...

  • Lucent Technologies LA41CF - page 5

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 5 DO NOT permanently place furniture or other items such as decorative pillows within 60" of the fireplace front face. ASSEMBLY STEPS Note: The following steps represent the normal sequence of installation. Each installation is unique, however, and might require a different sequence. 1. Position ...

  • Lucent Technologies LA41CF - page 6

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 6 FIREPLACE SPECIFICATIONS Figure 10 Figure 8 Figure 9 Blocking Metal Safety Strips Note: Safety strips are not required when fire- place rests on a noncombustible surface. Note: Install the hearth extension only as illus- trated. The safety strips should extend from front of the fireplace at least 1 ...

  • Lucent Technologies LA41CF - page 7

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 7 Note: The framed depth, 28 ¹⁄₈ " (714 mm) from a framed wall, must always be measured from a finished surface. If a wall covering such as drywall is to be attached to the rear wall, then the framed depth must be measured from the drywall surface. It is important that this dimen- sion be e ...

  • Lucent Technologies LA41CF - page 8

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 8 Step 4. Fireplace should be secured to side framing members using the full length nailing tabs at the top and bottom of the fireplace front face. Use 8d nails or equivalent ( Figure 17 ). For remodeling, plumb to center of flue collar from ceiling above, drive nail through ceiling from below to mar ...

  • Lucent Technologies LA41CF - page 9

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 9 Step 4. Note: Chimney sections are constructed with a unique locking tab design, which en- sures an immediate, tight assembly between sections. Plan your chimney requirements care- fully before assembly as chimney is difficult to disassemble after installation. If disassembled, the tabs might becom ...

  • Lucent Technologies LA41CF - page 10

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 10 Locking Band Mastic Figure 29 Step 9. Security Chimneys locking bands, Model FLB, may be required if the chimney extends too high above the roof flashing. As a general rule, if the chimney extends more than 6' above the roof flashing, the use of locking bands is advisable to strengthen the ch ...

  • Lucent Technologies LA41CF - page 11

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 11 A ¹⁄₈ " diameter hole must be drilled in the chimney joint using a ¹⁄₈ " diameter drill. Hole should be drilled in center of joint overlap ( Figure 37 ). Be sure to drill only through the outer chimney casting. Do not puncture the inner flue. Maximum offset of chimney system is ...

  • Lucent Technologies LA41CF - page 12

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 12 Figure 35 A 1 C 1 B 1 B 2 C 2 A 2 A 1 C 1 B 1 B 2 C 2 A 2 Figure 36 Chimney Section Joints No. 8 x 1/2" SMS Screws Required At Every Joint Past 6' No Screws Required In Joints For First 6' of Offset 4' 6' FTF10 VERTICAL ELEVATION CHART 1 1 0 1 1 100 1 7 1 5 010 21 ¹⁄₄ ...

  • Lucent Technologies LA41CF - page 13

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13 Figure 37 Figure 38 Underside Of Chimney Chimney Section (S) FTF10-E30 Return Elbow* FTF10-30 Offset Elbow* B A *Part of Offset/Return Package Model FTF10-ES30 INSTALLING OFFSETS First, review the Offset Elevation Chart and Figure 38 for reference. Step 1. Determine the offset distance where chimn ...

  • Lucent Technologies LA41CF - page 14

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 14 Note: See Framing and Dimension Chart for the sizes of the ceiling and roof openings. The size of the roof opening varies with the degree of pitch of the roof. Offset Elbow Assembly Offset elbows install the same as chimney sections. First, snap the inner section INTO the preceding inner section o ...

  • Lucent Technologies LA41CF - page 15

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 15 Figure 42 Vent Free Appliances These units have been tested and approved to ANSI/IAS/AGA Z21.11.2 for use with unvented gas appliances and complies with the stan- dard for Factory-Built fireplaces, UL 127. The unit has been tested for use with any unvented gas log sets having a maximum rating of 4 ...

  • Lucent Technologies LA41CF - page 16

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 16 Figure 43 Figure 44 Methods of Determining Hearth Extension and Wall Shield Equivalents To determine the thickness required for any material when either the k or r values are known: T M = Thickness of material in inches k M = K value of desired material r M = R value of desired material T L = Mini ...

  • Lucent Technologies LA41CF - page 17

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 17 Figure 46 Figure 45 Secure the hearth extension to the floor to prevent possible shifting. FINISH TO YOUR TASTE There are a wide variety of “ finished looks ” for these fireplaces, from formal wall decor with elaborate mantels to rustic wood paneling or warm brick facings. Only noncombustible ...

  • Lucent Technologies LA41CF - page 18

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 18 63L16 FTF10-12 63L17 FTF10-18 Chimney Section 63L18 FTF10-36 Storm Collar 63L59 FSC 63L40 F10F6 Flashing 63L41 F10F12 Round Termination 63L423 FTF10-CTD Chase Termination (Square) 63L49 FTF10-CT1 Firestop Spacer (Flat) 63L36 F10FS-2 Chase Termination (Round) 63L46 FTF10-CTDT Chase Termination (Squ ...

  • Lucent Technologies LA41CF - page 19

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 19 ...

  • Lucent Technologies LA41CF - page 20

    NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 20 LENNOX reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © 2000 by LENNOX P/N 504,217M REV. D 12/2003 11 ...

メーカー Lucent Technologies カテゴリー Indoor Fireplace

Lucent Technologies LA41CFのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- LA41CFの取扱説明書
- Lucent Technologiesの製品カード
- パンフレット
- またはLucent Technologies LA41CFの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Lucent Technologies LA41CFの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Lucent Technologies LA41CFの取り付け説明書、サービスマニュアル、簡易説明書、またはLucent Technologies LA41CFのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Lucent Technologies LA41CFの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Lucent Technologies LA41CFデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがLucent Technologies LA41CFを使用するのを助ける技術的文書のことです。説明書は通常、全てのLucent Technologies LA41CFユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Lucent Technologiesの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Lucent Technologies LA41CFの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははLucent Technologies LA41CFの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Lucent Technologies LA41CFに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Lucent Technologies LA41CFデバイスの基本機能を使うにあたってのヒント。 Lucent Technologies LA41CFのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Lucent Technologies LA41CFに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるLucent Technologies LA41CFのメーカー/サービスへの連絡先に関する情報。

Lucent Technologies LA41CFについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもLucent Technologies LA41CFの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLucent Technologies LA41CFで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)