Viking CVMOS200の取扱説明書

48ページ 1 mb
ダウンロード

ページに移動 of 48

Summary
  • Viking CVMOS200 - page 1

    DMOS200 CDMOS200 VMOS200 CVMOS200 In the interest of user-safety the oven should be restored to its original condition and only parts identical to those specifie d should be used. WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and current. Contact with the following parts may result in a sever ...

  • Viking CVMOS200 - page 2

    DMOS200 CDMOS200 VMOS200 CVMOS200 PRECA UTIONS T O BE OBSER VED BEFORE AND DURING SER VICING T O A V OID POSSIBLE EXPOSURE T O EXCESSIVE MICRO W A VE ENERGY (a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave sourc ...

  • Viking CVMOS200 - page 3

    1 CDMOS200 DMOS200 VMOS200 CVMOS200 Notes ...

  • Viking CVMOS200 - page 4

    2 CDMOS200 DMOS200 VMOS200 CVMOS200 W ARNING T O SER VICE PERSONNEL Microwave ovens contain circuitry capable of pro- ducing very high voltage and current, contact with following parts may result in a severe, possibly fatal, electrical shock. (Example) High Voltage Capacitor, High Voltage Power Trans- former, Magnetron, High Voltage Rectifier Assem ...

  • Viking CVMOS200 - page 5

    3 CDMOS200 DMOS200 VMOS200 CVMOS200 MICR O W A VE MEASUREMENT PR OCEDURE (CANAD A) After adjustment of the door switches are completed individually or collectively, switch test and microwave leakage test must be performed with survey instrument and test result must be confirmed to meet the requirement of the performance standard for microwave ovens ...

  • Viking CVMOS200 - page 6

    4 CDMOS200 DMOS200 VMOS200 CVMOS200 MICRO W A VE MEASUREMENT PR OCEDURE (USA) A. Requirements: 1 ) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven should not exceed 1mW/cm 2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition by a purchaser ...

  • Viking CVMOS200 - page 7

    5 CDMOS200 DMOS200 VMOS200 CVMOS200 VIKING RANGE CORPORA TION 111 Front St., Greenwood, MS 38930 Tel: (888) 845-4641 SER VICE MANU AL VIKING RANGE CORPORA TION MICROWAVE OVENS FOREWORD This Manual has been prepared to provide Viking Service Personnel with Operation and Service Information for the Viking Microwave Ovens, DMOS200, CDMOS200, VMOS200, ...

  • Viking CVMOS200 - page 8

    6 CDMOS200 DMOS200 VMOS200 CVMOS200 ITEM DESCRIPTION Power Requirements 120 Volts / 13.0 Amperes/1500Watts 60 Hertz Single phase, 3 wire grounded Power Output 1100 watts (IEC-705 TEST PROCEDURE) Operating frequency of 2450MHz Case Dimensions Width 24" Height 13-3/8" Depth 19-1/8" Cooking Cavity Dimensions Width 17-3/8" 2.0 Cubic ...

  • Viking CVMOS200 - page 9

    7 CDMOS200 DMOS200 VMOS200 CVMOS200 adapter properly grounded and polarized. If the extension cord must be used, it should be a 3-wire, 15 amp. or higher rated cord. Do not drape over a countertop or table where it can be pulled on by children or tripped over accidentally. CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR RE- MOVE THE ROUND GROUNDING ...

  • Viking CVMOS200 - page 10

    8 CDMOS200 DMOS200 VMOS200 CVMOS200 OPERA TION DESCRIPTION OF OPERATING SEQUENCE The following is a description of component functions during oven operation. OFF CONDITION Closing the door activates the door sensing switch and secondary interlock switch. (In this condition, the monitor switch contacts are opened.) When oven is plugged in, 120 volts ...

  • Viking CVMOS200 - page 11

    9 CDMOS200 DMOS200 VMOS200 CVMOS200 SENSOR COOKING CONDITION Using the SENSOR function, food is cooked without figuring time, power level or quantity. When the oven senses enough steam from the food, it relays the information to its microprocessor which will calculate the remaining cooking time and power level needed for best results. When the food ...

  • Viking CVMOS200 - page 12

    10 CDMOS200 DMOS200 VMOS200 CVMOS200 Figure O-2 Oven Schematic - Cooking Condition Figure O-1 Oven Schematic - Off Condition SCHEMATIC NOTE: CONDITION OF OVEN 1. DOOR CLOSED 2. CLOCK APPEARS ON DISPLAY SCHEMATIC 3. VARIABLE COOKING CONTROL "HIGH" 2. COOKING TIME PROGRAMMED 1. DOOR CLOSED NOTE: CONDITION OF OVEN 4. "START" PAD TO ...

  • Viking CVMOS200 - page 13

    11 CDMOS200 DMOS200 VMOS200 CVMOS200 DESCRIPTION AND FUNCTION OF COMPONENTS DOOR OPEN MECHANISM The door is opened by pushing the open button on the control panel, refer to the Figure D-1. When the open button is pushed, the open button pushes up the switch lever, and then the switch lever pushes up the latch head. The latch heads are moved upward ...

  • Viking CVMOS200 - page 14

    12 CDMOS200 DMOS200 VMOS200 CVMOS200 TR OUBLESHOO TING GUIDE Never touch any part in the circuit with your hand or an uninsulated tool while the power supply is connected. When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many of the possible causes of trouble will require that a sp ...

  • Viking CVMOS200 - page 15

    13 CDMOS200 DMOS200 VMOS200 CVMOS200 A MAGNETRON ASSEMBLY TEST 1. Disconnect the power supply cord, and then remove outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST Home fuse or circuit breaker blows when power cord is plugged into wall receptacle Monitor fuse blows ...

  • Viking CVMOS200 - page 16

    14 CDMOS200 DMOS200 VMOS200 CVMOS200 B POWER TRANSFORMER TEST 1. Disconnect the power supply cord, and then remove outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Disconnect the primary input terminals and measure the resistance of the transformer with an ohmmeter. Check for continuity of the coils with an oh ...

  • Viking CVMOS200 - page 17

    15 CDMOS200 DMOS200 VMOS200 CVMOS200 TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST 1. Disconnect the power supply cord, and then remove outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. If the capacitor is open, no high voltage will be available to the magnetron. Disconnect input leads and check for short or ...

  • Viking CVMOS200 - page 18

    16 CDMOS200 DMOS200 VMOS200 CVMOS200 TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST 1. Disconnect the power supply cord, and then remove outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Before performing this test, make sure that the primary switch is operating properly, according to the above Switch Test Pro ...

  • Viking CVMOS200 - page 19

    17 CDMOS200 DMOS200 VMOS200 CVMOS200 H BLOWN MONITOR FUSE TEST TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST 1. Disconnect the power supply cord, and then remove outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. If the monitor fuse is blown when the door is opened, check the primary switch and monitor switch ...

  • Viking CVMOS200 - page 20

    18 CDMOS200 DMOS200 VMOS200 CVMOS200 The following symptoms indicate a defective key unit. a) When touching the pads, a certain pad produces no signal at all. b) When touching a number pad, two figures or more are displayed. c) When touching the pads, sometimes a pad produces no signal. If the Key unit is defective. 1) Disconnect the power supply c ...

  • Viking CVMOS200 - page 21

    19 CDMOS200 DMOS200 VMOS200 CVMOS200 COMPU DEFROST TEST WARNING : The oven should be fully assembled before following procedure. ( 1 ) Place one cup of water in the center of the turntable tray in the oven cavity. (2) Close the door, touch the Defrost pad and touch the number pad 5 twice. Then touch the start pad. (3) The oven is in Compu Defrost c ...

  • Viking CVMOS200 - page 22

    20 CDMOS200 DMOS200 VMOS200 CVMOS200 1) Disconnect the power supply cord, and then remove outer case. 2) Open the door and block it open. 3) Discharge high voltage capacitor. 4) Follow the troubleshooting guide given below for repair. STEPS OCCURRENCE CAUSE OR CORRECTION 1 Only pattern at "a" is broken. *Insert jumper wire J1 and solder. ...

  • Viking CVMOS200 - page 23

    21 CDMOS200 DMOS200 VMOS200 CVMOS200 TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST Checking the initial sensor cooking condition Warning: The oven should be fully assembled before following procedure. 1) The oven should be plugged in at least two minutes before sensor cooking. 2) Room temperature should not exceed 9 5 o F(35 o C). 3) The unit sho ...

  • Viking CVMOS200 - page 24

    22 CDMOS200 DMOS200 VMOS200 CVMOS200 CHECKING CONTROL UNIT (1) Disconnect the power supply cord, and then remove outer case. (2) Open the door and block it open. (3) Discharge high voltage capacitor. (4) Disconnect the sensor connector that is mounted to control panel. (5) Then connect the dummy resistor circuit (see fig.) to the sensor connector o ...

  • Viking CVMOS200 - page 25

    23 CDMOS200 DMOS200 VMOS200 CVMOS200 TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST N NOISE FILTER TEST 1. Disconnect the power supply cord, and then remove outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Disconnect the leads to the primary of the power transformer. 5. Using an ohm-meter, check between the t ...

  • Viking CVMOS200 - page 26

    24 CDMOS200 DMOS200 VMOS200 CVMOS200 T OUCH CONTROL P ANEL ASSEMBL Y OUTLINE OF TOUCH CONTROL PANEL 4 ) Relay Circuit A circuit to drive the magnetron, fan motor, turntable motor and light the oven lamp. 5 ) Buzzer Circuit The buzzer is responsive to signals from the LSI to emit audible sounds (key touch sound and completion sound). 6 ) Synchronizi ...

  • Viking CVMOS200 - page 27

    25 CDMOS200 DMOS200 VMOS200 CVMOS200 16.7 msec. During cooking H : GND L : -5V LSI(IXA098DR) The I/O signal of the LSI(IXA098DR) is detailed in the following table. Pin No. Signal I/O Description 1 COM5 OUT Common data signal : COM11. Connected to LCD signal COM11. 2 COM4 OUT Common data signal : COM12. Connected to LCD signal COM12. 3 COM3 OUT Com ...

  • Viking CVMOS200 - page 28

    26 CDMOS200 DMOS200 VMOS200 CVMOS200 3 4 INT0 IN Signal synchronized with commercial power source frequency. This is the basic timing for time processing of LSI. 3 5 P07 O UT Key strobe signal. Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16 and P17 terminal while one of G1 line keys on key matrix is touched. 3 6 ...

  • Viking CVMOS200 - page 29

    27 CDMOS200 DMOS200 VMOS200 CVMOS200 4 9 AIN5 IN AH sensor input. This input is an analog input terminal from the AH sensor circuit, and connected to the A/ D converter built into the LSI. 5 0 AIN4 IN Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is an analog input terminal from the AH sensor circuit, and c ...

  • Viking CVMOS200 - page 30

    28 CDMOS200 DMOS200 VMOS200 CVMOS200 103-142 SEG39-SEG0 OUT Segment data signal. Connected to LCD. The relation between signals and LCD are as follows: LSI signal (Pin No.) LCD segment LSI signal (Pin No.) LCD segment SEG 39 (103) .......................... SEG 1 SEG 19 (123) ......................... SEG 21 SEG 38 (104) .......................... ...

  • Viking CVMOS200 - page 31

    29 CDMOS200 DMOS200 VMOS200 CVMOS200 ABSOLUTE HUMIDITY SENSOR CIRCUIT (1) Structure of Absolute Humidity Sensor The absolute humidity sensor includes two thermistors as shown in the illustration. One thermistor is housed in the closed vessel filled with dry air while another in the open vessel. Each sensor is provided with the protective cover made ...

  • Viking CVMOS200 - page 32

    30 CDMOS200 DMOS200 VMOS200 CVMOS200 1. Precautions for Handling Electronic Components This unit uses CMOS LSI in the integral part of the circuits. When handling these parts, the following precautions should be strictly followed. CMOS LSI have extremely high impedance at its input and output terminals. For this reason, it is easily influenced by t ...

  • Viking CVMOS200 - page 33

    31 CDMOS200 DMOS200 VMOS200 CVMOS200 To remove the outer case, proceed as follows. 1. Disconnect the power supply cord. 2. Open the oven door and block it open. 3. Remove the two (2) screws from the lower portion of the rear cabinet using a T20H Torx type or GTXH20-100 screw driver. 4. Remove the remaining two (2) screws from rear and four (4) scre ...

  • Viking CVMOS200 - page 34

    32 CDMOS200 DMOS200 VMOS200 CVMOS200 POWER TRANSFORMER REMOVAL Re-install 1. Rest transformer on the bottom plate with its primary terminals toward the oven face plate. 2. Secure transformer with four screws to bottom plate. 3. Re-connect wire leads (primary and high voltage) to power transformer and filament leads of transformer to magnetron and h ...

  • Viking CVMOS200 - page 35

    33 CDMOS200 DMOS200 VMOS200 CVMOS200 Terminal Push Pull down 1 2 Lever Positive lock¨ connector CONTROL PANEL ASSEMBLY REMOVAL POSITIVE LOCK ® CONNECTOR (NO-CASE TYPE) REMOVAL Figure C-2. Positive lock ® connector 1. Disconnect the power supply cord, and then remove outer case. 2. Open the door and block it open. 3. Discharge high voltage capaci ...

  • Viking CVMOS200 - page 36

    34 CDMOS200 DMOS200 VMOS200 CVMOS200 COOLING FAN MOTOR REMOVAL REMOVAL 1. Disconnect the power supply cord and then remove outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Disconnect the wire leads from the fan motor. 5. Remove the two (2) screws holding the fan motor to the oven cavity back plate. 6. Remove t ...

  • Viking CVMOS200 - page 37

    35 CDMOS200 DMOS200 VMOS200 CVMOS200 3. Secure latch hook (with two (2) mounting screws) to oven flange. 4. Make sure that the monitor switch is operating properly and check continuity of the monitor circuit. Refer to chapter "Test Procedure" and Adjustment procedure. DOOR SENSING SWITCH/PRIMARY SWITCH/SECONDARY SWITCH AND MONITOR SWITCH ...

  • Viking CVMOS200 - page 38

    36 CDMOS200 DMOS200 VMOS200 CVMOS200 6. Re-install choke cover to door panel by pushing. Note: After any service to the door; (A) Make sure that door sensing switch and secondary interlock switch are operating properly. (Refer to chapter “Test Procedures”.). (B) An approved microwave survey meter should be used to assure compliance with proper ...

  • Viking CVMOS200 - page 39

    37 CDMOS200 DMOS200 VMOS200 CVMOS200 6 45 1 2 3 6 45 1 2 3 A B C D E F G H A B C D E F G H Figure S-1. Pictorial Diagram HIGH VOLTA GE CA PA CI TO R HIGH V OL T AG E WI R E A H. V . R E C T IF IE R H I GH V O L T A GE C O M P O N EN T S OVE N LAM P AND S OC KE T MAG NE T R ON COM . MO NI T O R SW I TC H N.C . PRIM A R Y SW I TC H TURNTA BLE MO T O ...

  • Viking CVMOS200 - page 40

    38 CDMOS200 DMOS200 VMOS200 CVMOS200 6 45 1 2 3 6 45 1 2 3 A B C D E F G H A B C D E F G H Figure S-2 Power Unit Circuit + – + – + – A 1 CN - A R4 2 7 D5 T1 1 3 4 D1 D3 D2 D4 6 ab c d VR S 1 (J 1) D7 D8 1 SS2 7 0 A 1 SS2 7 0 A 10G 471K C 1 0. 1µ/ 50v C 3 0. 1µ/ 50v ZD1 HZ16 -1 C5 1 0 µ / 3 5 v C 2 1000µ/ 35v C 4 10µ/ 35v R1 2 . 4 k 1S S ...

  • Viking CVMOS200 - page 41

    39 CDMOS200 DMOS200 VMOS200 CVMOS200 6 45 1 2 3 6 45 1 2 3 A B C D E F G H A B C D E F G H Figure S-3 CPU Unit Circuit C- 10 C- 9 C- 1 C-8 C-12 F-1 F-2 F-3 G 1 G 2 G 3 G 4 G 5 G 6 G 7 G 8 G 9 G10 G11 G12 G13 G14 C-11 C- 3 C- 4 C-2 CN-C GND INT V C LE D V R V A OV E N LA M P TURNTAB L E M OTOR F A N M O TOR B UZZE RR M I CRO NC DOOR SENSING SWITCH N ...

  • Viking CVMOS200 - page 42

    40 CDMOS200 DMOS200 VMOS200 CVMOS200 6 45 1 2 3 6 45 1 2 3 A B C D E F G H A B C D E F G H Figure S-5 Printed Wiring Board of Power Unit WH - 1 SH - B SH - A 1 C3 C4 C5 R3 C2 F C1 10 D4 D2 D1 D3 (J1) D9 (D10) RY3 (CN - D) D8 ZD1 VRB DU R2 R1 R6 R5 SP1 3 E B D6 D5 Q2 R4 2 6 11 P S RY2 T1 AC VRS1 5 D7 OMIF DU 9 8 7 E Q1 B 4 E RY1 AC OL TTM FM B Q3 (C ...

  • Viking CVMOS200 - page 43

    41 CDMOS200 DMOS200 VMOS200 CVMOS200 REF. NO. PART NO. DESCRIPTION Q' TY CODE P AR TS LIST Note: The parts marked “ ∆ ∆ ∆ ∆ ∆ ” may cause undue microwave exposure. The parts marked “*” are used in voltage more than 250V. ∆ ∆ OVEN PARTS 4- 1 PM100013 H.V. Capacitor band 1 A B 4- 2 PM110017 Chassis support 1 A E 4- 3 PM1200 ...

  • Viking CVMOS200 - page 44

    42 CDMOS200 DMOS200 VMOS200 CVMOS200 REF. NO. PART NO. DESCRIPTION Q'T Y DOOR PARTS 5 - 1 PM110003 Door frame assembly (DMOS200) 1 A K 5 - 1 PM110004 Door frame assembly (CDMOS200) 1 A K 5 - 1 PM110001 Door frame assembly (VMOS200) 1 A K 5 - 1 PM110002 Door frame assembly (CVMOS200) 1 A K 5-1-1 PM120001 Latch head 1 A E 5-1-2 PM120007 Latch sp ...

  • Viking CVMOS200 - page 45

    43 CDMOS200 DMOS200 VMOS200 CVMOS200 6 45 1 2 3 6 45 1 2 3 A B C D E F G H A B C D E F G H OVEN AND CABINET PARTS 2-3 4-7 6-11 1-5 4-6 4-8 4-11 7-6 7-2 1-14 4-9 6-10 6-4 6-3 2-1 7-6 1-11 4-10 4-13 7-2 7-2 1-12 1-9 7-3 7-6 7-6 1-8 7-8 7-8 4-2 7-4 1-10 1-3 1-4 7-1 4-4 7-1 4-1 1-1 1-2 2-2 2-2 2-2 2-2 7-5 7-5 4-12 7-5 6-5 4-5 1-13 7-10 7-7 7-10 7-9 7-9 ...

  • Viking CVMOS200 - page 46

    44 CDMOS200 DMOS200 VMOS200 CVMOS200 6 45 1 2 3 6 45 1 2 3 A B C D E F G H A B C D E F G H 5-1 5-1-2 5-1-1 5-3 5-4 5-2 Actual wire harness may be different from illustration. 6-8 6-2 6-1 3-4 3-2 3-3 3-7 3-7 3-1 3-5 3-6 5-5 5-5 5-6 6-13 5-7 5-7 DOOR PARTS MISCELLANEOUS CONTROL PANEL PARTS ...

  • Viking CVMOS200 - page 47

    45 CDMOS200 DMOS200 VMOS200 CVMOS200 PACKING AND ACCESSORIES Non-replaceable items. DOOR PROTECTION SHEET PLASTIC BAG PACKING CASE TOP PAD ASSEMBLY INTO THE OVEN CAVITY 6-4 TURNTABLE TRAY 6-3 TURNTABLE SUPPORT 6-7 OPERATION MANUAL BOTTOM PAD ASSEMBLY TRAY HOLDER 6-9 RECIPE CARD ...

  • Viking CVMOS200 - page 48

    46 CDMOS200 DMOS200 VMOS200 CVMOS200 No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. COPYRIGHT © 2002 BY VIKING ALL RIGHTS RESERVED VIKING RANGE CORPORA TION 111 ...

メーカー Viking カテゴリー Microwave Oven

Viking CVMOS200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CVMOS200の取扱説明書
- Vikingの製品カード
- パンフレット
- またはViking CVMOS200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Viking CVMOS200の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Viking CVMOS200の取り付け説明書、サービスマニュアル、簡易説明書、またはViking CVMOS200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Viking CVMOS200の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Viking CVMOS200デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがViking CVMOS200を使用するのを助ける技術的文書のことです。説明書は通常、全てのViking CVMOS200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Vikingの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Viking CVMOS200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははViking CVMOS200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Viking CVMOS200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Viking CVMOS200デバイスの基本機能を使うにあたってのヒント。 Viking CVMOS200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Viking CVMOS200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるViking CVMOS200のメーカー/サービスへの連絡先に関する情報。

Viking CVMOS200についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもViking CVMOS200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがViking CVMOS200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)