-
Wells FT-18 - page 1
WELLS MANUFA CTURI NG COMP ANY 2 ERI K CIRCLE , P . O . Box 280 V erd i, NV 8943 9 Cust omer Serv ice (77 5) 345 -0444 Ext .502 fa x: (775) 345- 0569 www .wel lsbl oomfiel d.com IMPORTA NT: DO NOT DISCARD THIS MANUAL This manual is considered to be part of the appliance an d is to be given to the OWNER or MANAGER of the restaurant, or to the person ...
-
Wells FT-18 - page 2
Unless otherwise specified, all commercial cooking equip- ment manufactured by WELLS MFG. CO. is warranted against defects in materials and workmanship for a period of one year from the date of origin al installation or 18 m onths from the date of shipment from our f actory , whichever comes first, and is for the b ene fi t of the original purchase ...
-
Wells FT-18 - page 3
WARRANTY xi SPECIFICATIONS 1 FEATURES & OPERATING CONTROLS 2 PRECAUTIONS & GENERAL INFORMATION 3 AGENCY LISTING INFOR MATION 4 INSTALLATION 4 OPERATION 5 CLEANING INSTRUCTIONS 6 MAINTENANCE PROCEDURES 7 TROUBLESHOOTING SUGGESTIONS PARTS & SERVICE CUSTOMER SERVICE DATA Thank You for purchasing this Wells Manufacturing Co. appliance. Prop ...
-
Wells FT-18 - page 4
FEATURES & OPERATING CONTROLS (continued) 2 ...
-
Wells FT-18 - page 5
This appliance is intended for u se in commercial establishments only. This appliance is intended to prepare food for hum an consumption. No other use is recommended or authorized by the manufacturer or its agents. Operators of this app liance m u st be familiar with the appl iance use, limitations and associated restrictions . Operating instru ct ...
-
Wells FT-18 - page 6
INSTALL A TION NOTE: DO NOT discard the carton or other packing materials un til you have inspected the appliance for hidden damage and tested it for proper operation. Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside f ront cover of this manual. WARNING: Risk of persona l injury Installation procedures m ust be perf ormed by a qualif ied tech ...
-
Wells FT-18 - page 7
OPERATION 5 WA RM-U P During warm-up, both display s flash w hile showing the last-used MENU temperature setpoint. A MENU cycle cannot be started while in w arm-up mode. When setpoint temperature is reach ed, the display stops flashing and the audible alert beeps 3 times. SEASONING THE PL A TENS The platens must be seasoned before attem p ting to t ...
-
Wells FT-18 - page 8
CLEANING INSTRUCTIONS PRECAUTIONS: Press MENU 4 (c leaning mo de). Allow toaster to cool to 275ºF. NOTE: If MENU 4 has been programmed to anything other than 275º F, press PO W ER SWITCH OFF and allow unit to cool for at least 10 minutes. Be sure to w ear protective gloves. FREQUENCY: Dail y TOOLS P rotective gloves Cleans er manufactured sp ecif ...
-
Wells FT-18 - page 9
A D JU ST PL A TEN TENSION 1. ADJUSTMENT LOCATION a. Right platen tension adjuster is located on back of the toaster, on back side of the right upright. b. Left platen tension adjuster is located on back of the toaster, on front side of the left upright. 2. TO ADJUST a. Loosen lock nut. b. Turn adjust scre w until platen rais es easily, latches sec ...
-
Wells FT-18 - page 10
STANDARD OPERATION NOTES: Standard pre-set MENU programs are as follow: PROGRAM T EMP TIME FUNCT ION 1 450º 00:14 2 450º 00:27 3 450º 00:35 4 275º 00:00 C LEANING On start-up or changing program setti ngs, the displ a y will flash until the new temperature setpoint is reached (i.e. heater cycles on or off). This occurs whether approaching a set ...
-
Wells FT-18 - page 11
Set the time with MENU 3 (increas e) and MENU 4 (decrease). Press TEMP to save the time. The display will now advance to show zone temperature setpoints: 1.450 = Zone 1 @ 450ºF 2.450 = Zone 2 @ 450ºF 3.450 = Zone 3 @ 450ºF 4.450 = Zone 4 @ 450ºF Set the temperat ure setpoint for Zone 1 w ith MENU 3 (increase) and MENU 4 (decrease). Press TEMP t ...
-
Wells FT-18 - page 12
TROUBLESHOOTING SUGGESTIONS 10 SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY Toaster will not heat (no lights or display) Unplugged or circuit breaker tripped Plug toaster into appropriate circuit. Reset circuit breake r Damaged cord or plug Contact your Authorized W ells Service Agency for repairs One side d oes not heat Zone tem p not programmed Progra ...
-
Wells FT-18 - page 13
DESCRIPTI ON P A RT NO. CRUMBTRAY 503606 IMPORTANT: Use only factory authorized serv ice parts and replacement filters . For facto ry au thorized service, or to o rder factory author ized replacement parts, contac t your Wells authoriz ed service agency, or call: Well s Manufac turing C o . 2 Erik Circle P. O. Box 280 Verdi, NV 89439 phone: (775) 3 ...
-
Wells FT-18 - page 14
WELL S M ANUFACTURI NG COMP ANY D IVIS ION OF C A RRI ER RE FRIG ER A T ION 2 E RIK CIR CL E, P . O. B ox 28 0 V er d i , NV 89439 Cust omer S ervi ce (77 5) 345 -0444 Ext.5 02 fax: (775) 345-0569 www .wel lsbl oomfi eld. com W ells Man ufactur ing pro udly sup port s CFESA Comm ercial F ood Equi pment Ser vice Associ ation ...
Wells FT-18についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもWells FT-18の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWells FT-18で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。