-
Hans Grohe Axor 35115801 - page 1
Steel 35115801 Steel 35116801 Installation Instructions / W arranty ...
-
Hans Grohe Axor 35115801 - page 2
2 W all Mounted Single-Handle Lav Set with Base Plate 35115801 W all Mounted Single-Handle Lav Set 35116801 35115801 35116801 T echnical Information Max. flow rate: 1.5 gpm Max. water pressure: 147 psi Recommended pressure: 14.7 - 72 psi T est pressure: 232 psi Max. hot water temperature: 176° F* Recommended hot water temp.: 120° F - 140° F* *Kn ...
-
Hans Grohe Axor 35115801 - page 3
3 Seal the wall around the plaster shields with waterproof sealant. Failure to seal the wall can lead to possible water damage. Installation Remove the covers from the plaster shields (1). T rim the plaster shields so that they extend 1/16” outside the surface of the finished wall (2). Use a 17 mm socket wrench to remove the spout plug. Use a 27 ...
-
Hans Grohe Axor 35115801 - page 4
4 Install the cup washers and springs in the rough. Install the cartridge assembly . Push the handle over the cartridge stem. T ighten the handle screw with a 2 mm Allen wrench. If you are installing 35115801, turn to page 5. If you are installing 35116801, turn to page 9. ...
-
Hans Grohe Axor 35115801 - page 5
5 Model 35115801 only: Measure the distance between the wall surface and the end of the handle (x). If x is between 3 1/4” and 3 5/8”, select the two “A” sleeves (1 1/4”). If x is between 3 4/8” - 4”, select the two “B” sleeves (7/8”). If x is greater than 4”, select the two “C” sleeves (1/2”). x A B C 1 1/4” 7/8” 1/ ...
-
Hans Grohe Axor 35115801 - page 6
6 Connect the fixation nuts to the sleeves. Measure the distance from the rough to the outside surface of the finished wall (X) (1). Add 1 3/4” to X. Cut the spout connecting thread so that it is X + 1 3/4” long (2). W rap the connecting thread with T eflon tape. Install the connecting thread. T ighten using an 8 mm Allen wrench. 1. 2. ...
-
Hans Grohe Axor 35115801 - page 7
7 T ighten the retaining nuts using the ser vice key . Lightly lubricate the o-rings on the spout and handle escutcheons with the enclosed lubricant (1). Push the escutcheons onto the baseplate (2). Push the baseplate against the wall (1). Thread the sleeves into the rough (2). 1. 2. 2. 1. ...
-
Hans Grohe Axor 35115801 - page 8
8 Push the spout over the connecting thread (1). T ighten the set screw with a 3 mm Allen wrench (2). Install the handle flange (3). 1. 2. 3. ...
-
Hans Grohe Axor 35115801 - page 9
9 Model 35116801 only: Measure the distance between the wall surface and the end of the handle (x). If x is between 3 1/4” and 3 5/8”, select the “A” sleeve (1 1/4”). If x is between 3 5/8” - 4”, select the “B” sleeve (7/8”). If x is greater than 4”, select the “C” sleeve (1/2”). x A B C 1 1/4” 7/8” 1/2” ...
-
Hans Grohe Axor 35115801 - page 10
10 Push the sleeve / handle escutcheon assembly into place over the handle (1). T ighten it by rotating it clockwise (2). Push the flange over the handle. Push the sealing ring into the handle escutcheon (1). Install the handle escutcheon onto the sleeve (2). 1. 2. 1. 2. ...
-
Hans Grohe Axor 35115801 - page 11
11 Measure the distance from the rough to the out- side surface of the finished wall (X) (1). Add 1 3/4” to X. Cut the spout connecting thread so that it is X + 1 3/4” long (2). W rap the spout connecting thread with T eflon tape. Install the spout connecting thread. T ighten it using an 8 mm Allen wrench. Install the spout escutcheon and spout ...
-
Hans Grohe Axor 35115801 - page 12
12 35115801 User Instructions Pivot the handle up to turn the water on, down to turn it off. Pivot the handle to the left for warmer water , to the right for cooler water . Replacement Parts on off 1 2 3 4 5 6 7 8 9 10 11 12 13 17 ...
-
Hans Grohe Axor 35115801 - page 13
13 35116801 1 flange 96908800 2 handle 35094800 3 handle escutcheon 96912800 4 spout escutcheon 96913800 5 baseplate 96927800 6 cartridge 96339000 7 aerator 95386800 8 spout 97282800 9 anti-twist device 97280000 10 connecting thread 97230000 11 extension kit 38982000* 12 set screw 97660000 13 nut 97601000 14 handle escutcheon 96909800 15 spout escu ...
-
Hans Grohe Axor 35115801 - page 14
14 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY ...
-
Hans Grohe Axor 35115801 - page 15
15 including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year , with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS W ARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT P A Y FOR: A. Conditions, malfunctions or damage not resulting from defects in material or w ...
-
Hans Grohe Axor 35115801 - page 16
16 US - Installation Instructions • Part No. 90505803 • Revised 12/2008 Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770-360-9880 • Fax 770-360-9887 www .hansgrohe-usa.com ...
Hans Grohe Axor 35115801についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもHans Grohe Axor 35115801の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHans Grohe Axor 35115801で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。