JVC NX-PN10の取扱説明書

31ページ 1.62 mb
ダウンロード

ページに移動 of 31

Summary
  • JVC NX-PN10 - page 1

    COMPACT COMPONENT SYSTEM NX-PN10 INSTRUCTIONS LVT2011- 001A [J] For customer use: Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No. cover_NX-PN10[J].fm Page 1 Tuesday, March 3, 2009 4:23 PM ...

  • JVC NX-PN10 - page 2

    G-1 Warnings, Cautions and Others Mises en garde, précautions et indications diverses CAUTION The button in any position does not disconnect the mains lin e. Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). The MAINS plug or an applia nce coupler is used as the disconnect devic e, the disconnect device shall ...

  • JVC NX-PN10 - page 3

    G-2 For Canada/pour le Canada THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS. CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPL ...

  • JVC NX-PN10 - page 4

    G-3 Caution: Proper Ventilation To avoid risk of electric shoc k and fire, and to pre vent damage, locate the apparatus as follows: 1. Front: No obstructions and open spacing. 2. Sides/Top/Back: No obstructions should be placed in the areas s hown by the dimensions below. 3. Bottom: Place on the level surface. Maintain an a dequate air path for ven ...

  • JVC NX-PN10 - page 5

    1 Contents Introduction .................... ................ ............. 2 Precautions ......... ........................ ............. .................. 2 Getting Started ............... .................... ......... 3 Connections .............. ............ ............ ............ .......... .... 4 Canceling the Display Demonstration (Demo ...

  • JVC NX-PN10 - page 6

    2 Introduction Thank you for purchasing a JVC product. Please read a ll instructions carefully befo re operatio n, to ensure yo ur complete understanding and to obtain the best possible performance from the unit. Precautions Installation • Install in a place which is level, dry and ne ither too hot no r too col d—between 5°C and 35°C (41°F a ...

  • JVC NX-PN10 - page 7

    3 Getting Started Supplied Accessories After unpacking, check to be sure that you have all the following ite ms. The number in parentheses indica tes the quantity of each piece supplied. • Remote control (1) • Lithium coin battery CR2025 (1) (The battery has been installed when shipped from the factory.) • FM antenna (1) • AC power cord (1) ...

  • JVC NX-PN10 - page 8

    4 Connections Connecting the Antenna NOTES: • Make sure the FM antenna does not touch any other terminals, c onnecting cords or the AC power cord. Also, keep the antenna away from metallic parts of the unit, connecting cords and the AC power cord. This could cause poor reception. Do not connect the AC power cord un til all other connections have ...

  • JVC NX-PN10 - page 9

    5 Connecting the Video Cord to View a Video/Pictur e from iPod When viewing a video/picture from iPod on your TV, use a composite video co rd (not supplied) to connect the VIDEO OUT jack on the unit a nd the composite video input on your TV. • After you have connected the unit, change the video input mode on your TV. For details, also refer to th ...

  • JVC NX-PN10 - page 10

    6 Canceling the Display Demonstration (Demo) When you connect the AC power cord f or the first time, the display demonstration starts automatically. • When you operate the unit, the display demonstration stops temporarily. If no operation is done for about 2 minutes, the unit starts the display demonstration again. • To activate again, hol d do ...

  • JVC NX-PN10 - page 11

    7 Main Unit Operating on the Main Unit Buttons Operations Turns on or off (standby) the po wer. Activates or de activates Motion Sensor (P.6). STANDBY lamp Remote control sensor Display (P.8) Illumination panel (P.10) Dock A (P.13) Dock B (P.13) Motion sensor (P.6) Basic Operations NX-PN10[J].BOOK Page 7 Thur sday, April 9, 20 09 8:55 AM ...

  • JVC NX-PN10 - page 12

    8 Display Information Activates or deactivates the display demonstration (P.6). Adds the powerfulness to the sound (P.11). Stops the timer sound and restarts it 5 minutes later (P.22). • iPod (P.14): Press: Reverse skip/forward skip. Hold down: Reverse search/for ward search. • FM (P.17): Tunes in to a station. • Changes the source to iPod /i ...

  • JVC NX-PN10 - page 13

    9 Remote Control Operating on the Remote Control Basic operations ST Lights up when FM stereo broadcast is receiv ed. MONO Lights up when FM monaural re ception mode is ac tivated. TUNED Lights up when an FM station of su fficient signal stre ngth is tuned in. FM Lights up when FM is selected as the source. 1/2/3 • Lights up when Timer is set (P. ...

  • JVC NX-PN10 - page 14

    10 To dim the display and ill umination panel—DIMM ER You can change the brightness of the display and ill umination panel. • Dimmer is canceled when you turn off the unit. To activate ECO mode Activating ECO mode allows you to reduce power consumpti on by turning off the display while on standby. • To cancel the mode, press ECO/DIMMER again. ...

  • JVC NX-PN10 - page 15

    11 To turn off the unit after a certain period of time—Sleep Timer • To check the time remaining before the shut-o ff time, press SL EEP once. If you press the button repeatedly, you can cha nge the shut-off time. To emphasize the sound—Sound Turbo You can add the powerfulness to the sound. • To cancel, press SOUND TURBO agai n. “OFF” a ...

  • JVC NX-PN10 - page 16

    12 You can connect 2 iPod devices to the unit and enjoy sound and video from them. Compatible iPod Models: * Only for still picture. If iPod does not play correctly, update iPod software to th e latest version. • For details about updating iPod, check on th e Apple web site <h ttp://www.apple.com>. • JVC does not assure the compatibility ...

  • JVC NX-PN10 - page 17

    13 Connecting iPod Connect iPod to dock A or B on the unit. You can have 2 iPod devices connected at the same time. • Make sure the unit is on standby when you connect iPod. NOTES: • Be careful not to damage the terminal on the dock when connecting/disconnecting iPod. • Close the cover of the dock when you do not connect iPod to the unit. Abo ...

  • JVC NX-PN10 - page 18

    14 Operations For details, also refer to th e instruction manual for iPod. *1 Not available for iP hone and iPod touch. *2 Not equipped with iPhone and iPod touch. NOTES: • Before viewing a video/picture from iPod on your TV, make the ap propr iate video setting on iPod. For details of th e setting, see t he inst ruction manual for iPod. • For ...

  • JVC NX-PN10 - page 19

    15 * Not equipped with iPhone and iPod touch. Buttons Operations Control of iPod On the unit On the remote — Confirms an i tem on the menu/screen. Center button * — Press: Applies Shuffle Play to iPod o r iPod selected as the source. Select the desired shuffle mode. “SHUFFLE” appear s for a while. • The shuffle icon lights up on the d isp ...

  • JVC NX-PN10 - page 20

    16 NOTES: • JVC is not responsible for any loss of or damage to iPod that might re sult from the use of this product. • Do not touch or hit the terminals of the dock and of iPod. It might cause dama ge to these terminals. • When you connect iPod to the dock, make sure the terminal on the dock is fu lly inserted into iPod. • Always set the v ...

  • JVC NX-PN10 - page 21

    17 Listening to FM Broadcasts Basic Operations Buttons Operations On the unit On the remote Selects FM as the sourc e. When an FM program is broadc asted in stereo, ST (stereo) lights up on the display (only when the reception is good). Press: Changes the frequency. Hold down and release: The unit starts searching for stations and stops when a stat ...

  • JVC NX-PN10 - page 22

    18 Presetting Stations You can preset 30 FM stations. NOTES: • When you unplug the AC power cord or if a power fa ilure occurs, the preset stations will be erased in a few days. • If you store a new station onto an occupied preset number, the station previously stored on that number will be erased. 1 Select FM a s the source. 2 Tune in to the s ...

  • JVC NX-PN10 - page 23

    19 Connecting Other Equipment By using a stereo mini plug cord (not supplied), you can connect other equipment with analog audio output jacks, such as a portable audio player, etc. • Refer to the instruction manua l supplied with the equipment. NOTE: Make sure the unit is on standby when c onnecting or disconnecting other equipment. Operations To ...

  • JVC NX-PN10 - page 24

    20 Setting the Clock Set the built-in clock before using Timer. • You can set the clock when the unit is turned on or on standby. • To exit from the clock setting, press CLOCK/TIMER as required. • To correct a misentry during the process, pre ss MENU/CANCEL. You can retur n to the previous step. • If a power failure occurs, the clock loses ...

  • JVC NX-PN10 - page 25

    21 • To exit from Timer setting, pres s CLOCK/TIMER as required. • To correct a misentry during the process, pre ss MENU/CANCEL. You can return to the previous step. 2 Select Timer you want to set. 3 Select Time r type. WEEKLY: See step 4 below. ONCE: Timer works once on a selected day of the week. 4 Select the desired day of the week. • When ...

  • JVC NX-PN10 - page 26

    22 To Cancel Timer NOTE: The settings you have made are me morized though you cancel Timer. To Turn off the Timer Sound briefly — Snooze Using Snooze, you can have the timer s ound stop and restart it 5 minutes later. • When the timer sound starts: – If you do not press SNOOZE with in 3 minutes after the timer so und starts, Snooze does not w ...

  • JVC NX-PN10 - page 27

    23 Troubleshooting If you have a problem with your unit, check this list for a possible solution before calling for service. General Power does not come on. The power plug is not inserted securely. Plug it in securely (P.5). Power turns on even though you turned off. Motion Sensor is activated (P.6). Adjustments or settings are suddenly canceled be ...

  • JVC NX-PN10 - page 28

    24 Specifications Accessories See page 3. Amplifier Output Power 10 W (5W+5W) a t 8 Ω (10%THD) Terminals AUDIO IN Input Sensitivity/ Impedance (1 kHz): LEVEL 1: 500 mV/47 k Ω LEVEL 2: 315 mV/47 k Ω LEVEL 3: 125 mV/47 k Ω Dock A and B for iPod/iPhone Compatible iPod/iPhone models: See page 12. Output power (each iPod dock): DC 5 V 500 mA VID ...

  • JVC NX-PN10 - page 29

    Do not attempt to service the product yourself warranty_NX-PN10[J].fm Page 1 Friday, March 6, 2009 10:13 AM ...

  • JVC NX-PN10 - page 30

    warranty_NX-PN10[J].fm Page 2 Friday, March 6, 2009 10:13 AM ...

  • JVC NX-PN10 - page 31

    NX-PN10 COMPACT COMPON ENT SYSTEM EN © 2009 Victor Company of Japan, Limited 0409YAMMDWBET cover_NX-PN10[J].fm Page 2 Tuesday, March 3, 2009 4:23 PM ...

メーカー JVC カテゴリー MP3 Docking Station

JVC NX-PN10のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- NX-PN10の取扱説明書
- JVCの製品カード
- パンフレット
- またはJVC NX-PN10の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、JVC NX-PN10の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、JVC NX-PN10の取り付け説明書、サービスマニュアル、簡易説明書、またはJVC NX-PN10のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、JVC NX-PN10の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

JVC NX-PN10デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJVC NX-PN10を使用するのを助ける技術的文書のことです。説明書は通常、全てのJVC NX-PN10ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

JVCの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. JVC NX-PN10の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJVC NX-PN10の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。JVC NX-PN10に関してこのドキュメントで見つけることができる全てのヒントの目次
3. JVC NX-PN10デバイスの基本機能を使うにあたってのヒント。 JVC NX-PN10のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。JVC NX-PN10に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJVC NX-PN10のメーカー/サービスへの連絡先に関する情報。

JVC NX-PN10についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJVC NX-PN10の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJVC NX-PN10で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)