-
Tripp Lite NetCommander B070-008-19 - page 1
W ARRANTY REGISTRA TION Register online today for a chance to win a FREE T ripp Lite product! www .tripplite.com/warranty Owner’ s Man ual Note: Follow these instructions and operating procedures to ensure correct performance and to prevent damage to this unit or to its connected devices. Copyright © 2010 Tripp Lite. All rights reserved. All tra ...
-
Tripp Lite NetCommander B070-008-19 - page 2
2 T able of Contents Features.. ......................................................................................... p. 3 Package Includes….. ...................................................................... p. 3 Accessories… ................................................................................. p. 3 Configuration… ...... ...
-
Tripp Lite NetCommander B070-008-19 - page 3
3 Features • 8-port or 16-port KVM switch with built-in 19" LCD display , keyboardand touch pad • Access and control multiple multi-platform computers from a single console • Hot-swappable:disconnect and reconnect USB computers without rebooti ...
-
Tripp Lite NetCommander B070-008-19 - page 4
4 1 2 3 4 5 6 7 8 9 10 11 12 13 Configuration F igur e 1 NetCommander KVM fr ont panel Fr ont View F igur e 2 NetCommander KVM Buttons A uto: When the LCD Menu is closed, pressing theA UT O buttonwill perform anAuto Adjust on the monitor screen.When the LCD Menu is open, ...
-
Tripp Lite NetCommander B070-008-19 - page 5
5 1 2 3 4 5 6 F igur e 3 NetCommander KVM rear panel Rear View Configuration (continued) Po wer Socket: The power cord plugs in here from the A C power source. On/Off Switch: T urns the KVM Switch on and off. Firmware Upgrade Port: Plug included f irmware upgrade cable into this port to down- load firmw are upgrade data. CPU Port Section: Plug the ...
-
Tripp Lite NetCommander B070-008-19 - page 6
Up to 100 ft 6 NetCommander Server Interface Unit (SIU) The NetCommander Server Interface Unit The Server Interface Unit gets its power from the connected computer . In the case of the NetCommander PS/2 ServerInterface Unit (B078-101-PS2), the poweris drawnfrom the ke yboard port. In the case of the NetCommander ...
-
Tripp Lite NetCommander B070-008-19 - page 7
7 Up to 100 ft F igur e 5 NetCommander USB Server Interface Unit Installation (continued) SIU = Ser ver Interface Unit Connecting a NetCommander USB Server Interface Unit (Model # B078-101-USB) 1. Connect the B078-101-USB V GA connector to the computers V GA port 2. Connect the B078-101-USB USB connector to the computers USB port 3.Connect on ...
-
Tripp Lite NetCommander B070-008-19 - page 8
1 2 1 2 8 Installation (continued) Rac kmount Considerations Rac kmounting the NetCommander KVM The NetCommander Console KVM is designed for mounting in a 1U rack system. For con- venience,a rack mounting kit is included for quick installation.The v arious mounting options are explainedin the se ...
-
Tripp Lite NetCommander B070-008-19 - page 9
Model : B070-016-19 Model : B072-008-1 or B072-016-1 Model : B072-008-1 or B072-016-1 9 Installation (continued) T o cascade twoor more NetCommander KVM switches, followthe instructions below . Connect up to 256 computers* using any combination of B072-008-1 and B072-016-1 KVM? ...
-
Tripp Lite NetCommander B070-008-19 - page 10
10 Switch between the connected computers using any of the following methods: • The OSD (On Screen Display) • K eyboardhotkeycommands The OSD is also used to adjust v arious settings. A confirmation label at the top of your monitor screen identifies which computer is currently selected. T o switch to the n ...
-
Tripp Lite NetCommander B070-008-19 - page 11
11 Operation (continued) F igur e 8 The OSD Main W indow Navigating the OSD T o mov e up and down,use the [ ] and [ ] arrow keys. T o jump from one column to the next (when relev ant),use the [T ab] k e y. T o exitthe OSD or to return to the previousOSD? ...
-
Tripp Lite NetCommander B070-008-19 - page 12
12 Operation (continued) General Settings W iththe highlight line on the word GENERAL, press [Enter] . The General Settings windo w appears (see Figure 10). F igur e 10 The General Settings window Security The Security option in the OSD General Settings Menu allows you to activ ate or deactiv ate Passw ord Security .? ...
-
Tripp Lite NetCommander B070-008-19 - page 13
13 Operation (continued) When you hav e cascaded KVM switches, a lowerlevelSwitch must hav e a differentOSD display hotke y than a higher le vel switch. T o change the top-lev el switch hotke y: 1. Highlight the Hotkey option in the OSD General Settings Menu 2. Press the space bar to toggle through the v ...
-
Tripp Lite NetCommander B070-008-19 - page 14
14 Reset OSD General Settings Menu to Defaults (F7) When in the OSD General Settings Menu, you can reset all of the options to the original defaultsettings, erasing anychanges you hav e made. If you ha vechanged the Security Passw ords, theywill be ...
-
Tripp Lite NetCommander B070-008-19 - page 15
15 Operation (continued) Time Settings In the Settings window navigate to the Time line and press [Enter] . The T ime settings windo w appears (see Figure 12). F igur e 12 T ime settings window SCN - Sets the amount of time spent on the selected computer when Auto Scanning. LBL - Sets the amount of time the OSD label that shows which computer is cu ...
-
Tripp Lite NetCommander B070-008-19 - page 16
16 Operation (continued) Security F igur e 13 The Security settings window The OSD offers an advanced password security system made up of three dif ferent security le vels,each having its ownaccess rights. Administrator (Status A): TheAdministratorhas access to all features of the KVM, allow - ing? ...
-
Tripp Lite NetCommander B070-008-19 - page 17
17 OSD HELP Window (F1) T o access the HELP window press [F1] . The HELP windo w is displayed (see Figure 15). F igur e 15 The HELP window Please note! All the functions in the Help window are performed from the OSD Main Menu. The Help window only serves as a reminder of the OSD function keys. User Settings 1. Highlight the Users option in the OSD ...
-
Tripp Lite NetCommander B070-008-19 - page 18
18 Operation (continued) Mo ving the Label (F6) Y ou can position the OSD label anywhere on the screen. T o position the label from the Main window: 1. Move to the desired computer using the Up and Down Arro w keys. 2. Press the [F6] ke y . The selected screen image and Identification label are displayed. 3. Use the arrow keys to mov e the label to ...
-
Tripp Lite NetCommander B070-008-19 - page 19
19 Firmware Upgrade (continued) 3. On the upgrade computer (the computer connected to the KVM via the firmware upgrade cable), go to theTrippLite website and downloadthe NetCommander Firmware Upgrade Utility .ex e file,Firmware Upgrade .tfp fileand FirmwareUpgrade information? ...
-
Tripp Lite NetCommander B070-008-19 - page 20
20 Firmware Upgrade (continued) 1.Check the firmw are versionsof the KVM (Switch Manager), KVM OSD (Switch OSD) and SIUs by clicking on the boxes nextto them and pressing the F/W V er sion button. Note: T o select a device , you must first unselect any boxes that have ...
-
Tripp Lite NetCommander B070-008-19 - page 21
21 Firmware Upgrade (continued) 7.T owardsthe end of the f irmware upgrade, a prompt will appear asking you if you want to set the OSD to its default settings. If yes, click the Y es button.If no, click the No button. The upgrade will continue. 8.? ...
-
Tripp Lite NetCommander B070-008-19 - page 22
22 Note: Disconnect device from A C mains befor e service operation! When using Firmware Update software you may at times get a Communication Error message. If a Communication Error message does appear during the update procedure, do the following: 1. Ensure that the RS232 Serial cable's RS232 connector i ...
-
Tripp Lite NetCommander B070-008-19 - page 23
23 USB/SUN Combo Ke ys The connected PS/2 keyboard does not have a special SUN keypad to perform special functions in the SUN Operating System environment. When a B078-101-USB (SIU) is connected to a SUN computer , the SIU emulates these SUN ke ys using a set of key combinations called Combo Ke ys. Se ...
-
Tripp Lite NetCommander B070-008-19 - page 24
24 1111 W . 35th Street, Chicago, IL 60609 USA www .tripplite.com/suppor t Note:This equipment hasbeen tested and found to comply with the limitsfor a ClassAdigital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful ...
Tripp Lite NetCommander B070-008-19についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもTripp Lite NetCommander B070-008-19の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTripp Lite NetCommander B070-008-19で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。