Linksys WAP11の取扱説明書

30ページ 1.03 mb
ダウンロード

ページに移動 of 30

Summary
  • Linksys WAP11 - page 1

    Instant Wireless TM Series Wireless Network Access Point Use this guide to install: W AP11 User Guide ...

  • Linksys WAP11 - page 2

    COPYRIGHT & TRADEMARKS Copyright © 2001 Linksys, All Rights Reserved. Instant Wire l es s ™ i s a register ed trade- mark of Linksys. Microsoft, Windows, and the Windows logo ar e registered trademarks of Microsoft Corporation. All other trademarks and brand names ar e the pr operty of their respective pr oprietors. LIMITED W ARRANTY Linksys ...

  • Linksys WAP11 - page 3

    Wireless Network Access Point Introduction The Instant Wireless TM Wir eless Network Access Point Don’ t be bound b y cabling restrictions an y longer! The Instant W ireless™ Netw ork Access Point from Linksys deli vers the freedom to conf igure your net- w ork your wa y . Utilization of state-of-the-art wireless technology gi ves y ou the abil ...

  • Linksys WAP11 - page 4

    Wireless Network Access Point 3 Planning Y our Wireless Network Network T opology A wireless LAN is a group of computers, each equipped with one Instant W ireless™ Netw ork Card. Computers in a wireless LAN must be conf igured to share the same radio channel. The Instant W ireless™ Netw ork Card pro vides access to a wired LAN for wire- less w ...

  • Linksys WAP11 - page 5

    Instant Wireless TM Series Getting to Know the Wireless Network Access Point The ADSL Modem Router’ s Rear Panel Y our Access P oint’ s ports, where netw ork cables are connected , are located on the rear panel of your Access P oint. The Wireless Network Access P oint’ s P orts Dipole Antenna Connectors These tw o round connections are w here ...

  • Linksys WAP11 - page 6

    Instant Wireless TM Series Connecting and Setting Up the Wireless Network Access Point 1. Locate an optimum location f or the Wir eless Netw ork Access P oint. The best place for your W ireless Netw ork Access P oint is usually at the center of your wireless netw ork, with line of sight to all of your mobile stations. 2. Fix the dir ection of the a ...

  • Linksys WAP11 - page 7

    3. W indo ws will no w ask you w here to search for the dri ver softw are. Select Specify a location and type in the blank f ield D:W AP11WIN9X (where “D” specif ies y our CD-R OM). Then, click the Ne xt button. 4. W indo ws will no w search for the dri ver . After W indo ws has ackno wledged f inding the dri ver , click the Ne xt button. 5. ...

  • Linksys WAP11 - page 8

    1. W indo ws 2000 will automaticall y identify the W ireless Network Access P oint, once it is connected to the PC, and prompt you to install the necessary driv er . Make sure that the Setup Utility CD is inserted into your CD-R OM driv e and click the Next button on the F ound Ne w Hard w ar e Wizard screen to proceed. 2. Select Sear ch for a suit ...

  • Linksys WAP11 - page 9

    5. W indo ws will no w install the dri v er f iles. Click the Finish button w hen com- pleted. 6. Continue on to the Conf iguring the W ir eless Netw ork Access P oint sec- tion for software installation. 13 3. Under “Optional Search Locations”, select Specify a location and click the Next button. 4. Y ou will be prompted to enter a path; type ...

  • Linksys WAP11 - page 10

    Instant Wireless TM Series Configuring the Wireless Network Access Point The W ireless Netw ork Access P oint can be conf igured one of tw o wa ys, through the USB Utility or the Access P oint SNMP Conf iguration Utility . USB Utility The USB Utility can be used when conf iguring the W ireless Network Access P oint through a USB connection and is c ...

  • Linksys WAP11 - page 11

    5. The Choose Destination Location screen will show y ou the default desti- nation chosen by the utility . It is recommended that you lea v e the default des- tination, but if you w ant to install this in another location, click the Br o wse button and select an alternate destination. When y ou are ready to continue, click the Next button. 6. The C ...

  • Linksys WAP11 - page 12

    • WEP . If y ou ha ve not enab led WEP encr yption, this will read Disab led. It will read Enabled w hen WEP encryption is in use. • Reconnect. If, for any reason, the USB connection to the W ireless Network Access P oint is disconnected , you can reconnect the USB cable and click the Reconnect button here. This will retrie ve all of the data f ...

  • Linksys WAP11 - page 13

    21 20 THE AD V ANCED T AB Before making any changes to the Advanced tab, please check y our wireless settings on other systems, as these changes will alter the effecti v eness of the W ireless Netw ork Access Point. In most cases, these settings do not need to be changed. • F ragmentation Thr eshold. If you e xperience a high packet error rate, t ...

  • Linksys WAP11 - page 14

    • Oper ational Mode by default is set to Access P oint . This is for connecting your wireless PCs to a wired netw ork. In most cases, no change is necessary to this default setting. If you are trying to make a wireless con- nection betw een tw o wired netw orks, select Wir eless Bridg e . If you are connecting to another W ireless Bridge, select ...

  • Linksys WAP11 - page 15

    THE SECURITY T AB WEP (W ired Equi valent Pri v acy) is a data pri v acy mechanism based on a 40 bit shared key algorithm, as described in the IEEE 802.11b standard. In order to utilize WEP encryption, all points in your wireless netw ork must ha ve WEP enabled and be set to the same Ke y Setting. F or easier conf iguration, it is strongly recommen ...

  • Linksys WAP11 - page 16

    27 • WEP Ke y Setting . This setting will be the conf iguration key used in accessing the wireless netw ork via WEP encr yption. T o generate an encryp- tion key: 1. T ype e xactly the same case sensiti ve P assphrase in the PassPhrase f ield. F or security pur poses, please create your o wn P assphrase. 2. Click the Done button to create the enc ...

  • Linksys WAP11 - page 17

    T o restore your temporary IP address conf iguration, follo w the steps belo w: 1. F ollo w steps 1 and 2 in the instructions abo ve. 2. Select either Specify an IP addr ess or Obtain IP address automaticall y and enter in the original values y ou noted earlier . 3. Click OK and click OK again in the Netw ork windo w . 4. Restart your computer . If ...

  • Linksys WAP11 - page 18

    30 • Channel. The wireless channel shared by all wireless de vices connected to this Access P oint. • WEP . If y ou ha ve not enab led the WEP encr yption protocol, this will read Disabled. It will read Enab led when the WEP encr yption protocol is in use. • Reset. If you are e xperiencing problems with y our wireless connection, click the Re ...

  • Linksys WAP11 - page 19

    THE AD V ANCED T AB Before making any changes to the Advanced tab, please check y our wireless settings as these changes will alter the effecti v eness of the W ireless Network Access P oint. In most cases, these settings do not need to be changed. • F ragmentation Thr eshold V alue. This value indicates ho w much of the Access P oint’ s resour ...

  • Linksys WAP11 - page 20

    • Basic Rates. The basic transfer rates should be set depending on the speed of your wireless netw ork. Older, slo w er wireless netw orks should be set at 1-2 (Mbps) while a faster wireless netw ork should be set at 1-2-5.5-11 (Mbps). V erify that y ou’ ve set the correct basic rate for your wireless net- w ork before clicking the A pply butto ...

  • Linksys WAP11 - page 21

    • WEP Ke y Setting . This setting will be the conf iguration key used in accessing the wireless netw ork via WEP encr yption. T o generate an encryp- tion key: 1. T ype e xactly the same case sensiti ve P assPhrase in the PassPhrase f ield. 2. Click the Done button to create the encryption keys. The P assphrase generates four unique keys. 3. Make ...

  • Linksys WAP11 - page 22

    T o enab le MA C Address Filtering f ollo w these steps: 1. Cr eate a text file (e.g. MAC.TXT) using Notepad or another te xt editor . 2. Enter the 10 digit MA C address of each adapter that y ou wish to author- ize communication with the Access P oint. ONE PER LINE!!!!!!!! 3. Sa v e the f ile. Be sure to note the full path to the sav ed f ile. 4. ...

  • Linksys WAP11 - page 23

    What IEEE 802.11 featur es are supported? The product supports the following IEEE 802.11 functions: • CSMA/CA plus Ackno wledge protocol • Multi-Channel Roaming • Automatic Rate Selection • R TS/CTS feature • Fragmentation • P o w er Management What is Ad-hoc? An Ad-hoc wireless LAN is a group of computers, each with a WLAN adapter , co ...

  • Linksys WAP11 - page 24

    What is DSSS? What is FHSS? And what ar e their differ ences? Frequenc y-hopping spread-spectrum (FHSS) uses a nar rowband carrier that changes frequency in a pattern that is kno wn to both transmitter and receiv er . Properly synchronized , the net ef fect is to maintain a single logical channel. T o an unintended receiv er , FHSS appears to be sh ...

  • Linksys WAP11 - page 25

    44 DSSS - Also kno wn as “Direct Sequence Spred Spectr um”, this is a variety of radio transmission methods that continuously change frequencies or signal pat- terns. Direct sequence spread spectr um (DSSS), which is used in CDMA, mul- tiplies the data bits by a v ery fast pseudo-random bit patter n (PN sequence) that "spreads" the da ...

  • Linksys WAP11 - page 26

    46 RJ-45 - A connector similar to a telephone connector that holds up to eight wires, used for connecting Ethernet devices. Roaming - The ability to use a wireless de vice and be able to mo ve from one access point’ s range to another without losing the connection. Static IP Addr ess - A permanent IP address that is assigned to a node in a TCP/IP ...

  • Linksys WAP11 - page 27

    Specifications Standards: IEEE 802.3 (10BaseT), IEEE 802.11b (Wireless) Channels: 11 Channels (US, Canada) 13 Channels (Europe) 14 Channels (Japan) P orts: One 10BaseT RJ-45 P ort, One USB P ort Cab ling T ype: 10BaseT: UTP Category 3 or Better USB: USB Cable Operating Rang e Indoors: 30M (100 ft.) up to 11 Mbps (Wir eless): 50M (165 ft.) up to 5.5 ...

  • Linksys WAP11 - page 28

    51 Warrant y Information BE SURE T O HA VE Y OUR PR OOF OF PURCHASE AND A B ARCODE FR OM THE PR ODUCT'S P ACKA GING ON HAND WHEN CALLING. RETURN REQUESTS CANNO T BE PR OCESSED WITHOUT PR OOF OF PURCHASE. IN NO EVENT SHALL LINKSYS’ LIABILITY EXCEED THE PRICE P AID FOR THE PR ODUCT FR OM DIRECT , INDIRECT , SPECIAL, INCIDEN- T AL, OR CONSEQUEN ...

  • Linksys WAP11 - page 29

    Contact Information F or help with the installation or operation of this product, contact Linksys Customer Support at one of the phone numbers or Inter net addresses below . Sales Information 800-546-5797 (LINKSYS) T ech Support and RMA Issues 866-242-8558 Fa x 949-261-8868 Email support@linksys.com We b http://www .linksys.com FTP Site ftp.linksys ...

  • Linksys WAP11 - page 30

    © Copyright 2001 Linksys, All Rights Reserved. http://www .linksys.com ...

メーカー Linksys カテゴリー Network Router

Linksys WAP11のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WAP11の取扱説明書
- Linksysの製品カード
- パンフレット
- またはLinksys WAP11の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Linksys WAP11の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Linksys WAP11の取り付け説明書、サービスマニュアル、簡易説明書、またはLinksys WAP11のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Linksys WAP11の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Linksys WAP11デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがLinksys WAP11を使用するのを助ける技術的文書のことです。説明書は通常、全てのLinksys WAP11ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Linksysの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Linksys WAP11の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははLinksys WAP11の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Linksys WAP11に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Linksys WAP11デバイスの基本機能を使うにあたってのヒント。 Linksys WAP11のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Linksys WAP11に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるLinksys WAP11のメーカー/サービスへの連絡先に関する情報。

Linksys WAP11についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもLinksys WAP11の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLinksys WAP11で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)