-
Grindmaster 20 - page 1
GB T able of Contents W arning Labels . . . . . . . . . . . . . . . . . . . . . . . .2 T echnical Data . . . . . . . . . . . . . . . . . . . . . . . . .2 Unit Installation . . . . . . . . . . . . . . . . . . . . . . . .3 W ater Hook-up . . . . . . . . . . . . . . . . . . . . . . . . .3 Electrical Hook-up & St art-up Procedure . . . . .4 Brewing ...
-
Grindmaster 20 - page 2
...
-
Grindmaster 20 - page 3
Grind ’n Brew Coffee Systems Page 2 English W ARNING LABELS The following warning labels were on your grinderbrewer when it shipped from the factory . They should remain on your grinderbrewer in good, readable condition at all times. If one of your labels is missing or damaged, order a replacement label immediately . Part# 71 104 Located on outsi ...
-
Grindmaster 20 - page 4
Page 3 Grind ’n Brew Coffee Systems English Grind ‘n Brew Inst allation, S t art-up, and Brewing Instructions: (Read Completely!) Import ant: This brewer should be installed by a knowledgeable and experienced commercial equipment installer . Brewer Content s Y our brewer package should include the following: 1-Grinderbrewer (either single or du ...
-
Grindmaster 20 - page 5
Electrical Hook-up and S t art-Up Procedure (All Models) (Do not plug in unit yet!) Import ant: This equipment must be installed in compliance with applicable Federal, S tate, and/or Local electrical codes having jurisdiction. Do not use extension cords. Make sure that outlet brewer plugs into is grounded. Import ant: Make sure “Main Power Switch ...
-
Grindmaster 20 - page 6
Page 5 Grind ’n Brew Coffee Systems English GRIND’N BREW T imer settings/ with new PDS Flow control valve A st andard 1,9L bottle Grind’n Brews All Airpot Grind’n Brews Import ant: Brewers are factory set for throw weight and water portion. Please check that installation is correct before making adjustment. No adjustments should be necessar ...
-
Grindmaster 20 - page 7
Page 6 Grind ’n Brew Coffee Systems Figure E Figure F Setting Grind: T ool Required: #2 Phillip s screwdriver , 7/8"/2.2cm box wrench, large flat blade screwdriver 1. Remove front decal panel by removing screw on underside of panel. 2. Loosen adjusting screw lock nut by turning counter clockwise. 3. T urn slotted adjusting screw clockwise to ...
-
Grindmaster 20 - page 8
English Page 7 Grind ’n Brew Coffee Systems SHEAR PLA TE REPLACEMENT T ools Required: #2 Phillip s Screwdriver , Large flat blade screwdriver 1. Unplug machine. 2. Remove front panel and hopper . T o remove hopper , pull bean shut-off valve forward. This will shut- off the flow of cof fee beans and allow you to lif t it from the grind head. 3. Re ...
-
Grindmaster 20 - page 9
English Page 8 Grind ’n Brew Coffee Systems CONTROL BOARD SETTINGS J1 Jumper should remain on pin 1 & 2 J2 Jumper Controls -No pin connected with jumper-No minimum brewing temperature -Jumper connecting 2 & 3 - Low temperature no brew . The brewing cycle with wait until temperature of water is ready before continuing (factory setting) -Ju ...
-
Grindmaster 20 - page 10
Page 9 Grind ’n Brew Coffee Systems English 185ÞF/85ÞC oz (100 grams) of coffee. ...
-
Grindmaster 20 - page 11
Page 10 Grind ’n Brew Coffee Systems English For additional questions please cont act your local Grindmaster distributor and have model and serial number ready so that information can be given. Prior authorization must be obt ained from Grindmaster ’ s T echnical Services Dep artment for all warranty claims. ...
-
Grindmaster 20 - page 12
English Page 1 1 Grind ’n Brew Coffee Systems ...
-
Grindmaster 20 - page 13
English Page 12 Grind ’n Brew Coffee Systems ...
-
Grindmaster 20 - page 14
Page 13 Grind ’n Brew Coffee Systems English ...
-
Grindmaster 20 - page 15
Page 14 Grind ’n Brew Coffee Systems DESCRIPTION RIGHT BASKET ARM LEFT BASKET ARM BRACKET , BASKET ARM CENTER SPRING RIGHT BASKET ARM SPRING LEFT BASKET ARM SPRING SHOULDER BOL T , 5/16" X 5/8" SS SP ACER, 5/8" X 1/4" NUT , ESNA 1/4-20 SS SWITCH, SNAP ACTION SCREW , 4-40 X 5/8" NUT , 4-40 BELLOW W ASHER, 1/4" ID SAE ...
-
Grindmaster 20 - page 16
Page 15 Grind ’n Brew Coffee Systems English ...
-
Grindmaster 20 - page 17
Page 16 Grind ’n Brew Coffee Systems DESCRIPTION HOPPER CRADLE ASSEMBL Y FLANGED SLEEVE, .183" OD SS SCREW , 6-32 X 1/2" PH RD HD SS HOPPER LID ASSEMBL Y HOPPER ASSEMBL Y WINGNUT , ESNA 1/4-20 BOL T , CARRIAGE 1/4-20 X 1/2" SS BEAN SHUTOFF HOPPER GASKET SCREW , 8-32 X 1/2" PH TR SS FRONT P ANEL ASSEMBL Y NUT , ESNA 6-32 SPRING ...
Grindmaster 20についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもGrindmaster 20の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGrindmaster 20で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。