Advantech PCA-6185の取扱説明書

114ページ 4.12 mb
ダウンロード

ページに移動 of 114

Summary
  • Advantech PCA-6185 - page 1

    PCA-6185 Full-size socket 478 Intel® Pen- tium® 4 processor-based PCI-X bus CPU card User’s Manual ...

  • Advantech PCA-6185 - page 2

    PCA-6185 User’s Manual ii Copyright This document is copyrighted, 200 2, by Advantech Co., Ltd. All rights are reserved. Advantech Co ., Ltd. reserves the right to make improve- ments to the products descri bed in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, t ...

  • Advantech PCA-6185 - page 3

    iii A Message to the Customer Advantech customer services Each and every Advantech pro duct is built to the most exacting specifica- tions to ensure reliable performance in the harsh and demanding condition s typical of industrial environ ments. Whether your new Advantech equipment is destined for the laboratory or the factory floor , you can be as ...

  • Advantech PCA-6185 - page 4

    PCA-6185 User’s Manual iv PCA-6185 series co mparison tab le PCA-6185F- 00A1 V V V 4 V V X V V PCA-6185G2- 00A1 V V V 4 V V X V X PCA-6185VG- 00A1 V V V 4 V V V X X PCA-6185V - 00A1 V V V 4 V V X X X Model CPU: Support single Intel ® Pentium ® 4 socket 47 8 processor System chipset: Serverworks GC-SL L2 Cache (128/256 /512KB) depends on CPU USB ...

  • Advantech PCA-6185 - page 5

    v Product warranty Advantech warrants to you, the original purchaser , that each of its prod- ucts will be free from defects in mate rials and workma nship for two years from the date of purchase. This warranty does not apply t o any products which have b een repaired or altered by persons other than repair perso nnel authorized by Advantech, or wh ...

  • Advantech PCA-6185 - page 6

    PCA-6185 User’s Manual vi I ni t i a l In s p e c ti o n Before you begin installing your card, please make su re that the following materials have been shipped: •1 socket 478 Pentium 4® processor-based single board computer •1 PCA-6185 startup Manual •1 CD driver utility and manual (i n PDF format) •1 FDD cable, P/N: 1701340703 •2 UDM ...

  • Advantech PCA-6185 - page 7

    vii Contents Chapter 1 Hardware Co nfiguration ................................. 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Features ............. ......................... ......................... .............. 3 1.3 Specifications ............ ......................... .................. ...

  • Advantech PCA-6185 - page 8

    PPC-153 User’s Manual viii 2.5 VGA Connector (CN7) ................. .............. .................... 22 2.6 10/100/1000Base-T Ethernet (CN8 and CN34) .............. 23 2.7 Serial Ports (CN9: COM1; CN10: COM2) ..................... 23 2.8 PS/2 Keyboard and Mouse Co nnectors (CN11) ............. 24 2.9 External Keyboard Connector (CN12)........ ...

  • Advantech PCA-6185 - page 9

    ix Figure 3.7:Integrated peripherals ................. ........... ...... 39 3.6.1 IDE Funt ion Setup ................ ............ ........... ........... ...... 39 3.6.2 Super I/O Functi on Setup ..................... ........... ........... .. 40 3.6.3 Onboard Devices. .............. ........... .................. ......... ...... 40 3.6.4 PWRO ...

  • Advantech PCA-6185 - page 10

    PPC-153 User’s Manual x 7.8 Using SCSI Disk Utilities . .......................... .............. ...... 77 7.9 Installation u nder Windows NT/Win dows 2000 ............. 77 7.10 Windows 2000 Driver set up procedure .......... ........... ...... 78 7.11 Windows NT Driver Setup Procedure ..... ....................... 82 Appendix A Programming the ...

  • Advantech PCA-6185 - page 11

    CHAP TER 1 Hardware Configuration This chapter provides background information on the PCA-6185. It will show you how to configure the card to match your applica tion and prepare it for installation into your PC. ...

  • Advantech PCA-6185 - page 12

    PCA-6185 User’s Manual 2 Chapter 1 Hardware Configuration 1.1 Introduction The PCA-6185 Series all -in-one indu strial grade single CPU card uses Intel's high performance Pentium® 4 processor , together with the Server- W orks' GC-SL chipset. The card featur es two separate 64-bit PCI-X bus, one for internal deviced and one for externa ...

  • Advantech PCA-6185 - page 13

    3 Chapter 1 1.2 Features 1. High performance PCI bus: The PCA-6185 provides three inde- pendent PCI buses: one 32-bit, 33 MHz PCI bus and two 64-b it PCI-X buses. The 32-bit bus is used for on-board VGA controller . One of the two high performance PCI-X bus is used for onb oard Gigabit Ethernet and SCSI controllers. The other PCI-X bus is available ...

  • Advantech PCA-6185 - page 14

    PCA-6185 User’s Manual 4 1.3 Specifications 1.3.1 System • CPU: Intel Pentium® 4 /Celeron processor with 512, 256 or 128 KB L2 cache, up to 3.06 GHz and above, FSB 400/533 MHz • BIOS: A w ard Flash BIOS, 4 MB • System Chipset: ServerW o rks ServerSet GC-S L • Enhanced IDE hard disk drive interface: Supports up to four IDE large hard disk ...

  • Advantech PCA-6185 - page 15

    5 Chapter 1 1.3.4 VGA interface • On-board PCI VGA controller • Controller: A TI 3D RAGE XL • Display memory: 8 MB SDRAM 1.3.5 Ethernet LAN • Chipset: Broadcom BCM5703 for single GbE and BCM57 04 for dual GbE. • Ethernet interface: 10/100/1000 Based - TX • Connection: Onboard RJ-45 connector 1.3.6 Industrial features • W atchdog timer ...

  • Advantech PCA-6185 - page 16

    PCA-6185 User’s Manual 6 1.4 Jumpers and Connectors Connectors on the PCA-6185 board link it to external devices such as hard disk drives and a keyboard. In addition, the board has a num ber of jumpers used to configure your system for your application. The tables below list the function of each of the board jumpers and con- nectors. Later sectio ...

  • Advantech PCA-6185 - page 17

    7 Chapter 1 CN34 LAN2 CN35 System Fan CN40 PCI-X daughter board connector for SCSI & LAN CN50 Ultra 320 SCSI 1 CN51 Ultra 320 SCSI 2 T able 1.2: Connectors ...

  • Advantech PCA-6185 - page 18

    PCA-6185 User’s Manual 8 1.5 Board Layout: Jumper and Connector Locations Figure 1.1: Jumper and connecter locations ...

  • Advantech PCA-6185 - page 19

    9 Chapter 1 Figure 1.2: Daughter board layout Figure 1.3: Daughter bo ard extension I/Os 68 pin for Ultra 320 68 pin for Ultra 320 LAN1 LAN2 LAN 2 LAN 1 COM1 USB 0,1 VGA PS/2 mouse & keyboard ...

  • Advantech PCA-6185 - page 20

    PCA-6185 User’s Manual 10 Notes: Note1: Shall any inco mpatibility occur when using add-on car ds running at 66MHz PCI or 66 MHz PCI-X, please lower down the PCI bus frequency to 33MHz by setting jumpers on the backplane. Y ou can find how to set the jumpers on the User 's Note of th e backplane . Note 2: Due to the limita t ion of the GC-SL ...

  • Advantech PCA-6185 - page 21

    11 Chapter 1 1.6 Safety Precautions 1.7 Jumper Setti ngs This section provides i nstructions on how to confi gure your card by set- ting jumpers. It also includes the card's default settings and your optio ns for each jumper . 1.7.1 How to set jumpers Y ou configure yo ur card to match the needs of your applicat ion by setting jumpers. A jumpe ...

  • Advantech PCA-6185 - page 22

    PCA-6185 User’s Manual 12 closed for just a few seconds, and then move the jump er back to 1-2 closed. This procedure will reset the CMOS to its default setting. T able 1.3: CMOS clear (J1) Function Jumper set ting * Keep CMOS data 1-2 closed Clear CMOS data 2-3 closed * default setting ...

  • Advantech PCA-6185 - page 23

    13 Chapter 1 1.7.3 PCI bus type setting selection (JP1) The PCA-6185 CPU card co ntains a jump er that can set PCI bus type for 33/66 PCI bus or PCI-X, that's depending on add-on cards or backplane setting. * default setting 1.7.4 CPU FSB Frequency setting (JP7) The PCA-6185 CPU card contains a jumper that can set CPU FSB fre- quency on 533 MH ...

  • Advantech PCA-6185 - page 24

    PCA-6185 User’s Manual 14 1.8 System Memory The top-left edge of the PCA-6185 contains three so ckets for 184-pin dual inline memory modules (DIMMs) . All these sockets accept only 2.5 V registered DDR SDRAM. Register ed DIMMs are available in capaci- ties of 128, 256, 512, 1024 or 2048 MB. The sockets can be filled in any combination with DIMMs ...

  • Advantech PCA-6185 - page 25

    15 Chapter 1 automatically locked the memory mo dul e into the correct position of the DIMM socket. T o remov e the memory module, just push both handles outward, and the m emory module wi ll be ejected by the mechanism in the socket. 1.10 Cache Memory Since the second level (L2) cache ha s been embedded into the Intel® Pentium® 4 processor , you ...

  • Advantech PCA-6185 - page 26

    PCA-6185 User’s Manual 16 3. Press the lever down. The plate wi ll slide forward. Y ou will feel some resistance as the pressure starts to secure the CPU in the socket. This is normal and will not damage the CPU. 1.12 RAM Module Approval List 1.13 Gigabit LAN Ca rd Approval List Module V endor Module Part No. Chip s Memery Size Apacer 77.10312.46 ...

  • Advantech PCA-6185 - page 27

    17 Chapter 1 1.14 RAID Card Approval List Card V end or Card Part No. S pee d type. Adaptec SCSI RAID 3000S PCI64 bits / 66MHz (Dual channel / Ultra-160 ) Mylex AccleRAID 352 PCI64 bits / 66MHz (Dual channel / Ultra-160) Mylex AccleRAID 170 PCI32 bits / 33MHz (Single channel / Ultra-160) ...

  • Advantech PCA-6185 - page 28

    PCA-6185 User’s Manual 18 ...

  • Advantech PCA-6185 - page 29

    CHAPTER 2 Connecting Peripherals This chapter tells how to connect peripherals, sw itches, and indicators to the PCA-6185 board. ...

  • Advantech PCA-6185 - page 30

    PCA-6185 User’s Manual 20 Chapter 2 Connecting Peripherals 2.1 Primary (CN1) and S econdary (CN2) IDE Connec- tors Y ou can attach up to four IDE (Integrated Drive Electronics) drives to the PCA-6185’ s built-in controller . The primary (CN1) and secondary (CN2) connectors can each accommodate two drives. W ire number 1 on the cable is red or b ...

  • Advantech PCA-6185 - page 31

    21 Chapter 2 2.2 Floppy Drive Connector (CN3) Y ou can attach up to two flo ppy disk drives to the PCA-6185's onboard connector . Y ou can use 3.5" (720 KB, 1.44/2.88 MB) drives. The card comes with a 34-pin daisy- chain drive connector cable. On one end of the cable is a 34-pin flat-cable connector . On the other end are two sets of 34-p ...

  • Advantech PCA-6185 - page 32

    PCA-6185 User’s Manual 22 plate. Next, attach the flat-cable connector to CN4 on the CPU card. W ire 1 of the cable is red or blue, and the other wires are gray . Make sure that wire 1 corresponds to pin 1 of CN4. Pin 1 is on the upper right side of CN4. 2.4 USB Port s (CN6/CN26) There is one onboard USB pin head is available, CN26. The adapter c ...

  • Advantech PCA-6185 - page 33

    23 Chapter 2 2.6 10/100/1000Base-T Ethernet (CN8 and CN34) The PCA-6185 is equipped with one high -performance 64-bit PCI-bus Ethernet interface, which are fully co mpliant with IEEE 802.3/u 10/100/ 1000 Mbps CSMA/CD standards. They are supported by all major net- work operating syst ems. The RJ-45 jacks on the rear plate provide conve- nient 10/10 ...

  • Advantech PCA-6185 - page 34

    PCA-6185 User’s Manual 24 2.8 PS/2 Keyboard a nd Mouse Connectors (CN1 1) The 6-pin mini-DIN connectors (CN11) on the card mounting bracket provides connection to a PS/2 keyboard and a PS/2 mouse, by usin g the adapter cable (P/N: 17000 60202, available from Adv antech.) 2.9 External Keyboa rd Connector (CN12) In addition to the PS/2 mouse/keyb o ...

  • Advantech PCA-6185 - page 35

    25 Chapter 2 2.1 1 Front Panel Conn ectors (CN16, 17, 18, 19, 21&22) There are several external switches to monitor and control the PCA-6185. 2.1 1.1 Power LED (CN16) CN16 is a 5-pin connector for the p ower on LED. Refer to Appendix B for detailed information on the pi n assignments. If a PS/2 or A T X power supply is used, the syst em's ...

  • Advantech PCA-6185 - page 36

    PCA-6185 User’s Manual 26 2.1 1.2 External speaker (CN17) CN17 is a 4-pin connector for an extenal speaker . If there is no external speaker , the PCA-6185 provides an onbo ard buzzer as an alternative. T o enable the buzzer , set pins 3-4 as closed 2.1 1.3 Reset (CN18) Many computer cases offer the convenie nce of a reset button. Connect the wir ...

  • Advantech PCA-6185 - page 37

    27 Chapter 2 2.1 1.5 SM Bus Connector (CN29) This connector is reserved for Advantech's SNMP-1000 HTTP/SNMP Remote System Manager . The SNMP-1000 allows users to monitor the internal voltages, temperature and fans from a remote comp uter through an Ethernet networ k. CN23 can be connected to CN3 or CN6 of SNMP-1000. Please be care- ful about t ...

  • Advantech PCA-6185 - page 38

    PCA-6185 User’s Manual 28 2.1 1.8 A TX feature connector (CN20) and sof t power switch connector (CN21) The PCA-6185 can support an advanced soft power switch function i f an A TX power supply is used. T o enable the soft power switch function: 1. Connect the 3-pin p lug of the cable to CN20 (A TX feature connec- tor). 2. Connect the power on/off ...

  • Advantech PCA-6185 - page 39

    CHAPTER 3 A ward BIOS Setup This chapter describes how to set the card’ s BIO S configuration data. ...

  • Advantech PCA-6185 - page 40

    PCA-6185 User’s Manual 30 Chapter 3 A ward BIOS Setup 3.1 Introduction A ward’ s BIOS ROM has a bui lt-in setup program t hat allows users to modify the basic system configu ration. This type of inform ation is stored in battery-backed memory (CMOS RAM) so that it retains th e setup information when th e power is turned o ff. 3.1.1 CMOS RAM aut ...

  • Advantech PCA-6185 - page 41

    31 Chapter 3 3.2 Entering Setup T urn on the computer and check for the “patch cod e”. If there is a number assigned to the patch code, it means that the BIO S supports your CPU. If there is no number assigned to the patch code, please contact Advan- tech’ s applications engineer to obtain an up-to -date patch code file. This will ensure that ...

  • Advantech PCA-6185 - page 42

    PCA-6185 User’s Manual 32 3.3 St andard CMOS Setup Choose the “Standard CMOS Features” option from the “Initial Setup Screen” menu, and the screen below will be displayed. This menu allows users to configure system components such as dat e, time, hard disk driv e, floppy drive, display , and memory . Figure 3.2: S tandard CMOS features sc ...

  • Advantech PCA-6185 - page 43

    33 Chapter 3 3.4 Advanced BIOS Features The “Advanced BIOS Features” scr een appears when choosing the “Advanced BIOS Features” item from th e “Initial Setup Screen” menu. It allows the user to configure the PC A-6185 according to his particular requirements. Below are some majo r items that are provided in the Advanced BIOS Features sc ...

  • Advantech PCA-6185 - page 44

    PCA-6185 User’s Manual 34 3.4.1 Boot Seq & Floppy Setup 3.4.1.1 Fi rst Boot/Second Boo t/T hird Boot/Oth er Boot Device Y ou can select the priority of yo ur boot devices. Choices are: Floppy , LS1 20, HDD-0, SCSI, CDROM, HDD-1, HDD-2, HDD-3, ZIP100, USB-FDD, USB-ZIP , US B -CDROM, USB-HDD, LAN, Dis- abled. 3.4.1. 2 Swap Flopp y Drive If the ...

  • Advantech PCA-6185 - page 45

    35 Chapter 3 3.4.2 Console Redirection 3.4.2.1 C o nsole Redir ection When enabled, system will attempt to redirect console vi a COM port. When disabled, system will attempt to redirect console only when key- board is absent. The baud rate is selectable as 9600, 19 200, 38400, 57600, 115200 bps. 3.4.2.2 A gent Connect V ia System will detect COM po ...

  • Advantech PCA-6185 - page 46

    PCA-6185 User’s Manual 36 3.4.4 V irus W arning If enabled, a warning message and alarm beep activates if someone attempts to write here. The commands are “Enabled” or “Disabled.” 3.4.5 Hyper-Threading T echnology "Enabled" for the Hyper-Threading opt imized OS, when used with Intel Pentium 4 CPU with Hyper-Threading technology ...

  • Advantech PCA-6185 - page 47

    37 Chapter 3 3.4.12 OS Select for DRAM > 64MB This setting allows selecting an OS with greater than 64MB of RAM. Commands are “Non-OS2” or “OS2.” 3.4.13 MPS V ersion Control for OS It is recommended to keep the s etting as default "1.4" ...

  • Advantech PCA-6185 - page 48

    PCA-6185 User’s Manual 38 3.5 Advanced Chip set Features By choosing the “Advanced Chipset Features” option from the “Initial Setup Screen” menu, the screen below will be displayed. Th is sample screen contains the manufacturer ’ s default values for the PCA-6185, as shown in Figure 3-4: Note: DRAM def ault timings ha ve been care fully ...

  • Advantech PCA-6185 - page 49

    39 Chapter 3 3.5.3 Scrubbing The settings are Enabled and Disabl ed. Scrubbing writes correc ted EC C data back into memory . 3.6 Integrated Peripherals 3.6.1 IDE Funtion Setup 3.6.1.1 On -Chip Primary/Secondary PCI IDE Enable/Disable the primary an d secondary IDE HDD interface. 3.6.1.2 IDE Prim/Secondar y Master/Slave PIO/UDMA Mode Each channel ( ...

  • Advantech PCA-6185 - page 50

    PCA-6185 User’s Manual 40 3.6.2 Super I/O Function Setup 3.6.2.1 Onboard FDC Contr oller When enabled, this field allo ws you to connect your floppy d isk drives to the onboard floppy disk drive connector instead of a separate controller card. If you want to use a dif ferent controller card to connect the floppy disk drives, set this field t o Di ...

  • Advantech PCA-6185 - page 51

    41 Chapter 3 3.6.3.2 USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus (USB) con- troller and you have a USB keyboard. The choice: Enabled, Disabled. 3.6.4 PWRON Af ter PWR-Fail This field lets you to determine the state that your computer returns after a power failure. If sets to Off, the PC will not boot after a p ...

  • Advantech PCA-6185 - page 52

    PCA-6185 User’s Manual 42 This category allows you to select the type (or degree) of power saving and is directly related to the following mo des: 1. HDD Power Down 2. Suspend Mode There are four selections for Powe r Management, three of which have fixed mode setti ngs. 3.7.3 V ideo Off Method Disable (default) No power management. Disables all ...

  • Advantech PCA-6185 - page 53

    43 Chapter 3 3.7.4 V ideo Off In Suspend When you select “Y es”: V ideo will trun off when computer suspends. When you select “No”: V ideo will be on when computer suspends. 3.7.5 Sof t-Off by PWRBTN If you choose “Instant-Off”, then pushing the A TX soft power switch but- ton once will switch the system to “system off” power mode. ...

  • Advantech PCA-6185 - page 54

    PCA-6185 User’s Manual 44 3.8.2 Reset Configuration Dat a Note: This is left “Disabled. ” Se lect “Enabl ed” to reset Extended System Configuration Data (ECSD) if you hav e installed a ne w add-on card and y our OS won’t bo ot and y ou need to reconfigure . 3.8.3 Resources controlled by: The commands here are “Auto” or “manual.” ...

  • Advantech PCA-6185 - page 55

    45 Chapter 3 3.9.2 Current System T emperature This shows you the current system temperature 3.9.3 Current CPU T emperature This shows you the current CPU speed. 3.9.4 Current CPU Fan/System Fan S peed This shows you the current CPU fan/System fan speed. 3.9.5 VCORE This shows CPU core voltage. 3.9.6 VCC3/+5V/+12V/-12V/-5V This shows you the voltag ...

  • Advantech PCA-6185 - page 56

    PCA-6185 User’s Manual 46 Enter the current passw or d and press <Enter>. 3. After pressing <Enter> (ROM password) or the current password (user-defined), you can change the password stored in the CMOS. The password must be no longer than eight (8) characters. Remember , to enable the password setting feature, you must first select ei ...

  • Advantech PCA-6185 - page 57

    CHAPTER 4 PCI SVGA Setup The PCA-6185 features an onboard PCI VGA interface. This chapter pro- vides instructions for installing and operating the softwa re drivers on the display driver CD included in your package. ...

  • Advantech PCA-6185 - page 58

    PCA-6185 User’s Manual 48 Chapter 4 PCI SVGA Setup 4.1 Before you begin T o facilitate th e installation of th e enhanced display device drivers and utility software, you shoul d read the instructions in this chapter carefully before you attempt installatio n. The enhanced display drivers for the PCA-6185 board are located on the software inst al ...

  • Advantech PCA-6185 - page 59

    49 Chapter 4 • Integrates superio r video features. These include filtered sealing of 720 pixel DVD content, and MPEG-2 motio n compensation for software DVD 4.3 VGA Inst allation First, insert CD drive. Then follow the Icons for your PCA Series model number . Click on the right driver for the auto-installation. Below take W i ndows 2000 as an ex ...

  • Advantech PCA-6185 - page 60

    PCA-6185 User’s Manual 50 In the license window , click on "Y es" to continue. ...

  • Advantech PCA-6185 - page 61

    51 Chapter 4 Click on "Y es". The installaion is complete click on "Y es" to restart the system. ...

  • Advantech PCA-6185 - page 62

    PCA-6185 User’s Manual 52 ...

  • Advantech PCA-6185 - page 63

    CHAPTER 5 LAN Configuration The PCA-6185 features single or d ual 10/100/1000Base-T Eth ernet LAN interface. This chapter gives detailed information on Ethernet config uration. It shows you how to configure the card to match your app lication requirements. ...

  • Advantech PCA-6185 - page 64

    PCA-6185 User’s Manual 54 Chapter 5 LAN Configuration 5.1 Introduction The PCA-6185 features single or dual 64-b it gigabit Ethernet networking interace. This interface supports bu s mastering architecture and auto- negotiation features. Therefore standard twisted-p air cabling with RJ-45 connectors for both 10 Mbps, 100 Mbps, and 1000 Mbps conne ...

  • Advantech PCA-6185 - page 65

    55 Chapter 5 5.4 Windows NT Drivers (Broadcom 5703/4) Procedure Note : The CD-ROM driv e is designated as "D" throughout 1. In the "W indows NT" screen, click on "Start" and select "Set- tings". Then click on the "Contro l Panel" icon to select "Net-work". 2. In the "Network" win ...

  • Advantech PCA-6185 - page 66

    PCA-6185 User’s Manual 56 3. In the "Select Network Adapter" window , click on "Have Disk...". 4. When the "Insert Disk" window appears, i nsert the utility CD into the CD-ROM drive. The correct file path is D:Drv_LanBROD5703(4)WindowsNTDriver . W hen you have the correct file path, cl ick on "OK". 5. I ...

  • Advantech PCA-6185 - page 67

    57 Chapter 5 6. In the "Microsoft TCP/IP Properties" window , select the "IP Address" tab. Then sele ct "Specify an IP address". T ype in the IP Address and Subnet Mask details. Then click on "OK". 7. In the "Network Settings Change" wind ow , click on "Y es" to restart the computer . ...

  • Advantech PCA-6185 - page 68

    PCA-6185 User’s Manual 58 5.5 Windows 2000 Drivers (Broadcom 5703/4) Proce- dure Note: The CD-R OM drive is designed as "D" thro ughout this sec- tion. 1. In the "W indows 2000" screen, click on " Start" and select " set- tings". Then click on the " Control Panel" icon to select "system" ...

  • Advantech PCA-6185 - page 69

    59 Chapter 5 3. In "Device Manager" screen, follow the screen instructions, to click on "Properties". 4. In the following screen, to click on "Update Driver". ...

  • Advantech PCA-6185 - page 70

    PCA-6185 User’s Manual 60 5. Click on "Next". 6. Following the highlighted item , and click on "Next". 7. Select "Network adapte r" and then click Next ...

  • Advantech PCA-6185 - page 71

    61 Chapter 5 8. Click on "Have Disk". 9. Key in "D:Drv_ )LanBROD5703(4)W indo ws2000Driver", then click on "OK". 10. T o highlight the follow ing item, and click "Next". ...

  • Advantech PCA-6185 - page 72

    PCA-6185 User’s Manual 62 1 1. Click "Next". 12. Press Y es to continue the installation 13. Click “Finish” to complete the installation ...

  • Advantech PCA-6185 - page 73

    CHAPTER 6 Onboard Security Setup This chapter explains OBS concepts and provides inst ructions for installin g the relevant software drivers. This is done using the driver CD included in your PCA-6185 package. ...

  • Advantech PCA-6185 - page 74

    PCA-6185 User’s Manual 64 Chapter 6 Onboard Security Setup 6.1 Introduction Onboard security (OBS) fun ctions monitor key hardware. They help yo u maintain your system’ s st ability and durability . The PCA-6185 can m onitor 5 sets of sy stem posit ive voltages, 2 sets of system negative voltages, CPU cooling fan speed, and CPU temperature. The ...

  • Advantech PCA-6185 - page 75

    65 Chapter 6 6.3 Windows XP/2000 Windows XP/2000 Drivers Set up Proced ure 1. Insert the driver CD into your system’ s CD-ROM drive. In a few seconds, the software installation main menu appears, as shown in the following figure. Click on the “IN ST ALL” button under the “OBS DRIVERS” heading. ...

  • Advantech PCA-6185 - page 76

    PCA-6185 User’s Manual 66 2. Click on OK to install OBS driver 3. After the setup is completed. Y o u can view OBS setting by running this utility . 4. It is recommended that you load the default values for all OBS set - tings. However , if desired, you can extab lish new conditions for voltage, fan speed, and temperature ...

  • Advantech PCA-6185 - page 77

    CHAPTER 7 SCSI Setup The PCA-6185 features an onboard SCSI interface. This chapter provides basic SCSI concepts and instructions for installing the soft ware drivers with the SCSI driver disks CD included in your package. ...

  • Advantech PCA-6185 - page 78

    PCA-6185 User’s Manual 68 Chapter 7 SCSI Setup 7.1 Introduction The PCA-6185 is equipped with an Adaptec AIC-7 902 single-chip PCI- to-SCSI host adapter wh ich provides a dual channel Ultra 320 multitask- ing interface between your computer’ s PCI bus and SCSI devic es (disk drives, CD-ROM drives, scanners, tape backups, remo vable media drives ...

  • Advantech PCA-6185 - page 79

    69 Chapter 7 7.3 SCSI IDs Each device attached to the SCSI bus, as well as the SCSI controller itself, must be assigned a unique SCSI ID n umber from 0 t o 15. A SCSI ID uniquely identifies each SCSI de vice on the SCSI bus and determines priority when two or more devices ar e trying to use the SCSI bus at the same time. Refer o the device’ s doc ...

  • Advantech PCA-6185 - page 80

    PCA-6185 User’s Manual 70 7.4 T erminating the SCSI bus T o ensure reliable communication on the SCSI bus, the ends of the SCSI bus must be properly terminated. This is accomplished when the device at the end of the each cable, or the end of the cable itself, has a terminator installed (or enabled). T erminators must be removed, or termin ation m ...

  • Advantech PCA-6185 - page 81

    71 Chapter 7 tems. Run SCSISelect if y ou need to change or vie w current settings , or if you w ould like to run the SCSI disk utilities. SCSI Select Options A vailab l e Settings Default Settings SCSI Bu s Interfa ce Definitions: Host Adapter SCSI ID 0-15 7 SCSI Parity Checking Enable, Disabled Enabled Host Adapter SCSI T ermination L VD/SE Conne ...

  • Advantech PCA-6185 - page 82

    PCA-6185 User’s Manual 72 Remarks: 1. Setting is valid only if Multipl e LUN Support is enabled 2. Settings are valid only if host adapter BI OS is enabled. 7.6 St arting SCSISelect Follow these steps to start SCSISelect: 1. T urn on or restart your system. During the startup process, pay car eful attention to t he messages that appear on your sc ...

  • Advantech PCA-6185 - page 83

    73 Chapter 7 7.7 Using SCSISelect Settings T o select an option, use the arrow keys to move the cursor to the option, then press ENTER. In some cases, selecting an option d isplays another meny . Y ou can retu rn to the previous menu at any time by pressing ESC. T o restore the original SC SISelect default values, press F6 from the main SCSISelect ...

  • Advantech PCA-6185 - page 84

    PCA-6185 User’s Manual 74 • Initiate W ide Negotiation -(Default: Y es) When set to Y es, the SCSI card attempts 1 6-bit data transfer ( w ide negot iation.) When set to No, the SCSI card uses 8-bit data transfer unless the SCSI device requests wide negotiation. Note: Set Initiate Wide Negoti at ion to NO if yo u are using an 8-bit SCSI de vice ...

  • Advantech PCA-6185 - page 85

    75 Chapter 7 system bootup. If this setting disabl ed, you can still invoke the SCSISe- lect Utility b y pressing <Ctrl> <A > after the SCSI card BIOS banner appears. • Extended BIOS T ranslation for DOS Drives > 1 GByte -(Default: Enabled) When set to Enabled, provides an ex tended translation scheme for SCSI hard disks with cap a ...

  • Advantech PCA-6185 - page 86

    PCA-6185 User’s Manual 76 • Support Removable Disks Un der BIOS as Fixed Disks —(Default: Disabled) Determines which removabl e-media drives are supported by the SCSI card BIOS. Choices are as follows: • Disabled — No removable-media drives are treated as hard disk drives. Software drivers are re quired because the drives are not controll ...

  • Advantech PCA-6185 - page 87

    77 Chapter 7 7.8 Using SCSI Disk Utilit ies T o access the SCSI disk uti lities, follow these steps: 1. Select the SCSI Disk Utilities option from the menu that appears after starting SCSISelect. SCSI Sel ect scans the SCSI bus (to deter- mine the devices installed) and di splays a list of all SCSI IDs and the devices assigned to each ID. 2. Use th ...

  • Advantech PCA-6185 - page 88

    PCA-6185 User’s Manual 78 7.10 Windows 2000 Driver setup procedure 1. In the window 2000 screen, click on “start” and select “setting.” Then click on the “Control Pa nel” icon to select “System” 2. In the “System properties”, choos e “PCI SCSI Bus Controller .” Then click on “Properties” ...

  • Advantech PCA-6185 - page 89

    79 Chapter 7 3. Click on “Update Driver” ...

  • Advantech PCA-6185 - page 90

    PCA-6185 User’s Manual 80 4. Click on “Next” 5. Recommend to serach for a better driver ...

  • Advantech PCA-6185 - page 91

    81 Chapter 7 6. If the SCSI driver is supplied in floppy disk, click on “Floppy di sk drives.” Then, click on “Next.” If the SCSI driver is supplied in CD-ROM disk, click on “Specify a location:" then enter "D:Drv_SCSIAdaptec7902 W indowsWin2000"” 7. The installation is completed. Cli ck on “Finish.” ...

  • Advantech PCA-6185 - page 92

    PCA-6185 User’s Manual 82 8. Click on “Y es” to restart the system. 7.1 1 Windows NT Driver Setup Procedure 1. In the W indows NT screen, click on “S tart” and select “Setting.” Then click on the “Control Panel” icon to select “SCSI Adapter .” ...

  • Advantech PCA-6185 - page 93

    83 Chapter 7 2. In the SCSI Adapter , choose “D rivers.” Cl ick on “Add” to install SCSI driver . 3. Click on “Have Disk.” ...

  • Advantech PCA-6185 - page 94

    PCA-6185 User’s Manual 84 4. Click on “Browse” to select the drivers . If the SCSI driver is sup- plied in floppy disk, choose the directory A:. 5. Click the SCSI driver , and then click “OK.” ...

  • Advantech PCA-6185 - page 95

    85 Chapter 7 6. The installation of SCSI Driver is completed. Click on “OK.” ...

  • Advantech PCA-6185 - page 96

    PCA-6185 User’s Manual 86 ...

  • Advantech PCA-6185 - page 97

    Appendix A Programming the W atchdog Timer The PPC-123 is equipped with a watch- dog timer that resets the CPU or gener- ates an interrupt if processing comes to a standstill for any reason. This feature ensures system reliability in industrial standalone or unmanned environm ents. ...

  • Advantech PCA-6185 - page 98

    PCA-6185 User’s Manual 88 Appendix A Programming the W atchdog Ti m e r A.1 Programming the W atchdog Timer T o program the watchd og timer , yo u must write a program which writes I/ O port address 444 (hex). The output data is a time interval value. The value range is from 01 (hex) to 3E (hex), and the related time in terval is from 1 sec. to 6 ...

  • Advantech PCA-6185 - page 99

    89 Appendix A The following example sh ows how you might program the watchd og timer in BASI C: 10 REM W atchdog timer examp le program 20 OUT &H44 4, data REM Start and restart the watchdog 30 GOSUB 1000 REM Y ou r application task #1, 40 OUT &H444, data REM Reset the timer 50 GOSUB 2000 REM Y ou r application task #2, 60 OUT &H444, da ...

  • Advantech PCA-6185 - page 100

    PCA-6185 User’s Manual 90 ...

  • Advantech PCA-6185 - page 101

    Appendix B Pin Assignment s ...

  • Advantech PCA-6185 - page 102

    PCA-6185 User’s Manual 92 Appendix B Pin Assignment s B.1 IDE Hard Drive Connector (CN1, CN2) T able B.1: IDE hard drive connector (CN1, CN2) Pin Signal Pin Signal 1 IDE RESET* 2 GND 3D A T A 7 4 D A T A 8 5D A T A 6 6 D A T A 9 7D A T A 5 8 D A T A 1 0 9 DA T A 4 10 DA T A 1 1 11 D ATA 3 1 2 D ATA 1 2 13 DA T A 2 14 DA T A 13 15 DA T A 1 16 DA T ...

  • Advantech PCA-6185 - page 103

    93 Appendix B B.2 Floppy Drive Connector (CN3) T able B.2: Floppy dr ive connector (CN3) Pin Signal Pin Signal 1 GND 2 FDHDIN* 3G N D 4 N / C 5 N/C 6 FDEDIN* 7 GND 8 INDEX* 9 GND 10 MOTOR 0* 1 1 GND 12 DRIVE SELECT 1* 13 GND 14 DRIVE SELECT 0* 15 GND 16 MOTOR 1* 17 GND 18 D IRECTION* 19 GND 20 STEP* 21 GND 22 WRITE DA T A* 23 GND 24 WRITE GA TE* 25 ...

  • Advantech PCA-6185 - page 104

    PCA-6185 User’s Manual 94 B.3 Parallel Port Connector (CN4) T able B.3: Paral lel port co nnector (CN4) Pin Signal Pin Signal 1 ST ROBE* 14 AUTOFD* 2D 0 1 5 E R R 3D 1 1 6 I N I T * 4D 2 1 7 S L C T I N I * 5D 3 1 8 G N D 6D 4 1 9 G N D 7D 5 2 0 G N D 8D 6 2 1 G N D 9D 7 2 2 G N D 10 ACK* 23 GND 11 B U S Y 2 4 G N D 12 PE 25 GND 13 SLCT 26 N/C * ...

  • Advantech PCA-6185 - page 105

    95 Appendix B B.4 USB Connector (CN6) T able B.4: USB1/USB2 connector (CN6) Pin USB1 Signal Pin USB2 Signal 1 +5 V 6 +5 V 2 UV - 7 UV - 3 UV+ 8 UV+ 4 GND 9 GND 5 Chassis GND 10 N/C B.5 VGA Connector (CN7) T able B.5: VGA conn ector (CN7) Pin Signal Pin Signal 1 RED 9 VCC 2 GREEN 10 GND 3 BLUE 1 1 N/C 4 N/C 12 SDT 5 GND 13 H-SYNC 6 GND 14 V -SYNC 7 ...

  • Advantech PCA-6185 - page 106

    PCA-6185 User’s Manual 96 B.6 Keyboard and Mouse Conn nector (CN1 1) T able B.6: Keyboard and m ouse connector (CN1 1) Pin Signal 1 KB DA T A 2M S D A T A 3G N D 4V C C 5 KB CLOCK 6M S C L O C K B.7 External Keyboard Connector (CN12) T able B.7: External keybo ard connector (CN12) Pin Signal 1C L K 2D A T A 3N C 4G N D 5V C C 5 3 1 2 4 6 ...

  • Advantech PCA-6185 - page 107

    97 Appendix B B.8 CPU Fan Powe r Connector (CN14) T able B.8: CPU fan power conn ector (CN14) Pin Signal 1G N D 2+ 1 2 V 3 Detect B.9 Power LED (CN16) Y ou can use an LED to indicate when the CPU card is on. Pin 1 of CN16 supplies the LED's power , and Pin 3 is the ground. T able B.9: Power LED (CN16) Pin Function 1 LED power (+5 V) 2N C 3G N ...

  • Advantech PCA-6185 - page 108

    PCA-6185 User’s Manual 98 B.10 External Speak er Connector (CN17) The CPU card has its own buzzer . Y ou can also connect it to the external speaker on your comput er chassis. T able B.10 : External speaker (CN17 ) Pin Function 1+ 5 V C C 2G N D 3 Internal buzzer 4 S peaker out B.1 1 Reset Connector (CN18) T able B.1 1: Rese t connector (CN18 ) P ...

  • Advantech PCA-6185 - page 109

    99 Appendix B B.12 HDD LED Connector (CN19) T able B.12 : HDD LED connector (CN19) Pin Signal 1 Vcc(LED+) 2 LED0 (LED-) B.13 A TX Feature Connector (CN20) T able B.13: A TX feature connecto r (CN20) Pin Signal 1 PS-ON 2V C C 3V C C S B 1 1 ...

  • Advantech PCA-6185 - page 110

    PCA-6185 User’s Manual 100 B.14 A TX Sof t Power Switch (CN21) T able B.14: A TX sof t power switch (CN21) Pin Signal 1 3VSB 2P W R - B T N B.15 SM Bus Connector (CN29) T able B.15: SM Bus conn ector (CN29) Pin Signal 1 SMB_CLK 2S M B _ D A T A 1 1 ...

  • Advantech PCA-6185 - page 111

    101 Appendix B B.16 System I/O Port s T able B.16: System I/O port s Addr . Range (HEX) Device 020 021 Programmable interrupt co ntroller 040 043 System timer 060 S tandard 101/102 key or Microsoft Natural PS/2 061 System speaker 064 064 S tandard 101/1 02 key or Microsoft Natural PS/2 070 073 System CMOS/real time clok 080 090 Direct memory access ...

  • Advantech PCA-6185 - page 112

    PCA-6185 User’s Manual 102 B.18 Interrupt Assignment s T able B.18 : Interrupt assignments Interrupt # Interru pt assignmen ts 0 (ISA) System timer 1 (ISA) S tandard 101 /102 key or Microsoft Natural PS/2 3 (ISA) Communications port (COM2) 4 (ISA) Communications port (COM1) 6 (ISA) S tandard floppy disk controller 8 (ISA) System CMOS/real time cl ...

  • Advantech PCA-6185 - page 113

    103 Appendix B B.20 PCI Bus Map T able B.20 : PCI bus map Function AD_Select PCI IRQ GNT Onboard LAN2 AD20 (CIOBX2) SIR Q5 (CIOBX2) SGNT0 (CIO BX2) Onboard LAN1 AD20 (CIOBX2) SIR Q6 (CIOBX2) SGNT0 (CIO BX2) Onboard VGA AD19 (CSB5) SIR Q4 (CSB5) SGNT0 (CSB5) SCSI AD21 (CIOBX2) SIRQ7, 8 SGNT1 (CIOBX2) PCI slot 1 AD31 Not Supported PCI slot 2 AD30 PIR ...

  • Advantech PCA-6185 - page 114

    PCA-6185 User’s Manual 104 ...

メーカー Advantech カテゴリー Computer Hardware

Advantech PCA-6185のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PCA-6185の取扱説明書
- Advantechの製品カード
- パンフレット
- またはAdvantech PCA-6185の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Advantech PCA-6185の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Advantech PCA-6185の取り付け説明書、サービスマニュアル、簡易説明書、またはAdvantech PCA-6185のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Advantech PCA-6185の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Advantech PCA-6185デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAdvantech PCA-6185を使用するのを助ける技術的文書のことです。説明書は通常、全てのAdvantech PCA-6185ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Advantechの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Advantech PCA-6185の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAdvantech PCA-6185の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Advantech PCA-6185に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Advantech PCA-6185デバイスの基本機能を使うにあたってのヒント。 Advantech PCA-6185のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Advantech PCA-6185に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAdvantech PCA-6185のメーカー/サービスへの連絡先に関する情報。

Advantech PCA-6185についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAdvantech PCA-6185の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAdvantech PCA-6185で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)