-
Roland VH-12 - page 1
03458434 ’05-10-6N Owner’s Manual The VH-12 V-Hi-Hat is to be used in combination with the Roland TD-20 or TD-12 Percussion Sound Module. fig.Structure * Hi-hat stand is not included. For details on compatible stands, refer to p. 10. 202 Copyright © 2004 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in a ...
-
Roland VH-12 - page 2
2 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. ................................................................................................ 002a • Do not open or perform any internal modifications on the unit. ......................................................... ...
-
Roland VH-12 - page 3
3 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Placement 354a • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can def ...
-
Roland VH-12 - page 4
4 Getting Started Similar Touch and Feel as with an Acoustic Hi-Hat The superior design has taken into account not only the shape of the hi-hat, but also the bounce of the stick, and even the movement caused by playing, making it possible to play with the same feel as an acoustic hi-hat. Smooth Transition Between Closed and Open Tones When you stri ...
-
Roland VH-12 - page 5
5 Mounting on the Hi-Hat Stand * Due to the different shape, the clutch included with the hi-hat stand cannot be used with the VH-12. Be sure to use the special VH-12 clutch. fig.Clutch.e 1. Use the tuning key included with the VH-12 to loosen the clutch bolt, then simultaneously turn and remove the clutch top. fig.Clutch-2.e 2. Remove the two lock ...
-
Roland VH-12 - page 6
6 Mounting on the Hi-Hat Stand 1. Remove the clutch included with the hi-hat stand from the cymbal rod. * The clutch included with the hi-hat stand will not be used. * It is not necessary to remove the felt (or rubber) pad on the hi- hat stand used for supporting the bottom cymbal. 2. Confirm that the cymbal rod is firmly secured. For instructions ...
-
Roland VH-12 - page 7
7 Mounting on the Hi-Hat Stand 6. Attach the clamp and holder to the pipe on the upper part of the hi-hat stand, then slightly tighten the assembly with the tuning key. fig.Bottom-03.e 7. Pass the ends of the holder through the grooves in the metal portion of the bottom hi- hat, then while strongly pulling the clamp downward, secure it with the tun ...
-
Roland VH-12 - page 8
8 Mounting on the Hi-Hat Stand 921 * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. 1. Connect the VH-12’s TRIGGER OUTPUT jack to the sound module’s TRIGGER INPUT HI-HAT jack, and the VH-12’s CONTROL OUTPUT jack to the sound m ...
-
Roland VH-12 - page 9
9 Mounting on the Hi-Hat Stand 1. Adjust the gap between the top hi-hat and bottom hi-hat to a clearance of approximately 10 mm, then tighten the clutch screw. fig.Gap.e * Although the gap can be adjusted to a clearance that makes playing the hi-hat easier, setting too narrow or wide a gap can cause improper function of the unit and prevent the hi- ...
-
Roland VH-12 - page 10
10 Playing Methods The hi-hat tone changes smoothly and continuously from open to closed in response to how far the pedal is pressed. You can also play the foot closed sound (playing the hi-hat with the pedal completely pressed down) and foot splash sound (playing the hi-hat with the pedal fully pressed and then instantly opening it). When you stri ...
-
Roland VH-12 - page 11
11 Troubleshooting Was the unit adjusted after being connected to the sound module? When using the VH-12, be sure to run the automatic offset adjustment on your sound module (p. 8). Is the TRIGGER OUTPUT connected to the sound module’s HH CTRL jack? Connect the VH-12’s TRIGGER OUTPUT jack to the sound module’s HI-HAT jack, and the CONTROL OUT ...
-
Roland VH-12 - page 12
As of August 1, 2005 (ROLAND) Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828 ...
Roland VH-12についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもRoland VH-12の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRoland VH-12で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。