Cub Cadet 394の取扱説明書

20ページ 2.61 mb
ダウンロード

ページに移動 of 20

Summary
  • Cub Cadet 394 - page 1

    PRINTED IN U .S.A. FORM NO. 769-01516 Model Number 394 190-394-100 IMPORTANT: 50" MOWER DECK READ SAFETY RULES A ND INSTRUCTIONS CAREFULLY INSTALLATION AND Operator’s Manual MAINTENANCE INSTRUCTIONS (10/04) CUB CADET LLC P .O . BO X 361131 CLEVEL AND, OHIO 44136-0019 [ www .cubcadet.com ] For Series 3000 Tractors ...

  • Cub Cadet 394 - page 2

    2 CONTENTS Section Page Safe Oper ation Practice s ............... ................ ............. ................ ................ ................. ......... .. 2 To The Owne r ................ ................ ................ ............. ................ ................ ................. .... ....... 5 I Tractor a nd Deck Prep aration . .... ...

  • Cub Cadet 394 - page 3

    3 5. Be sure the area is clear of other people before mowing. Stop machin e if anyone enters the a rea. 6. Never carry passengers. 7. Disengage the blades before shifting into reverse and backing up. Always look down and beh ind before and while backing. 8. Be aware of the mower and attachment discharge direction and do not point it at anyon e. Do ...

  • Cub Cadet 394 - page 4

    4 Do not try to stabilize the mach ine by putting your foot on the ground. Do not use the grass catcher on steep slopes. Do not tow heavy pull behind attachments (e.g. loade d dump cart, lawn roller) on slopes greater than 5 de- grees. When goin g downhill, the extra weight may cause you to loose co ntrol and possibly over turn the tractor. III. CH ...

  • Cub Cadet 394 - page 5

    5 14. Observe proper disposal laws and regulatio ns. Improper disposal of fluids and materials can harm the environment and the ecology. a. Prior to dispo sal, contact yo ur local Environmental Prot ection Agency to determine th e proper method fo r disposing of the waste. Recycling centers ar e established to properly d ispose of material s in an ...

  • Cub Cadet 394 - page 6

    6 SECTION I. TRACTOR AND DECK PREPARATION A. DECK PREPARATION WARNING When handling th e mower deck, be ca reful not to cut yourself on the sharp blades. Remove the top and break down the sides of the crate to remove the deck assembly from the shipping container. Cut the tie strap securing the front drive shaft to the deck assembly. Remo ve all pad ...

  • Cub Cadet 394 - page 7

    7 WARNING Place the tractor on a level surface and en gage the parking brake lever. NOTE Tractors built Mfg. Code 1K060G and after ar e equipped with a deck downstop featu re. In the raised position, the downstop will prevent the lift links from being adeq uate ly lowered to allow in- stallation of the deck. If the deck is being in- stalled on a tr ...

  • Cub Cadet 394 - page 8

    8 SECTION II. INSTALLATION AN D REMOVAL OF MOWER DECK A. INSTALLATION OF DECK After locking the left lift link as described in Section I , start the tractor and use the hydr aulic lift to fully raise the left lift link (See Figur e 5). Stop the engine. Figure 5 Adjust the mower deck to its lowest setting as f ollows: 1. Remove the hex fl ange lock ...

  • Cub Cadet 394 - page 9

    9 5. Unlock the left lift link by sliding the left lift rod fully rearward in the slot of the lift link (See Figure 8). Figure 8 NOTE The following step 6 applie s only to the initial installation of the mower deck on the trac tor. 6. Loosen the hex jam nuts on the front lift bracket / rod assembly and back o ff (unscrew) the hex lock nuts until ap ...

  • Cub Cadet 394 - page 10

    10 9. Guide the LH and RH lift links into the slots of th e rear deck brackets and release the deck support pins by aligning with the inner holes of the deck brackets (See Figure 12) NOTE: The han dle of the support pins should be positioned to the rear of the deck brackets as shown in Figure 12. Figure 12 10. Ma neuver each side of the deck slight ...

  • Cub Cadet 394 - page 11

    11 B. REMOVAL OF DECK Place the tractor and mower deck on a firm and level surface with enough room to slide the deck out from the left side of the tractor. WARNING Before removing th e mower deck, place the PTO switch in the “OF F” position, engage th e parking brak e lever, and tur n ignition key to the “OFF” position . Always stop the en ...

  • Cub Cadet 394 - page 12

    12 SECTION III. ADJUSTMENTS DECK LEVELING ADJUSTMENTS In order to achieve even cutting, the mower deck must be properly leveled. This leveling pr ocedure will result in the left and right blades having corresponding cutting- edge-to ground measurements within 1/16 inch of each other. Also, the blades will each have a 1/8 to 1/4 inch downward tilt t ...

  • Cub Cadet 394 - page 13

    13 Figure 19 2. Measure and record the distance from the front cutting edge to the ground (measure A), and from the rear cutting edge to the ground (mea sure B), for both outer blades. The front edge of each blade (measure A) should be lo wer than its back edge (measure B) by approximately 1/8 to 1/4 inch.See Figure 20. Figure 20 3. Adjust the fron ...

  • Cub Cadet 394 - page 14

    14 USING HEIGHT ADJUSTME NT KNOB NOTE Tractors built Mfg. Code 1K060G and after ar e equipped wit h a height adj ustment knob wh ich can be used to set the do wnstop position of th e mower deck. A full rotation of t he height adjustment knob eq uals ap- prox. a 1/4 inch ad justment in the deck height settin g. There are fou r detent positi ons per ...

  • Cub Cadet 394 - page 15

    15 SECTION IV. MAINTENANCE CLEANING THE DECK Using The Deck Wash Syst em WARNING When using the deck wash system, never engage the d eck from any position other than the operat or’s seat of the tr actor. Do not u se an assistant or engage de ck in the pr esence of an y bystanders. 1. Attach the nozzle a dapter to a standard gar den hose connected ...

  • Cub Cadet 394 - page 16

    16 When reinstalling the blades, be sure they are installed so that the wind wings are pointing upward toward the top of the deck. Tighten the nuts to 90 to 110 ft-lbs. (122 to 149 N·m). After replacing the blades, apply grease to the exposed threads at the bottom of the spindles to prevent rust buildup. LUBRICATION After every 10 hours of operat ...

  • Cub Cadet 394 - page 17

    17 Figure 2 8 INSTALL NEW SPINDLE BELT 1. Lift the gea r box / mounting b racket assembly to install the belt aroun d the rear of the drive pulley and through the center opening of the mounting bracket. 2. Install the gear box mounting bracket on the deck mounting plate and secure with the original fasteners removed earlier. 3. Slide the belt under ...

  • Cub Cadet 394 - page 18

    18 LUBRICATION GUIDE The life of any machine depends upon the care it is given. Proper lubrication is a very import ant part of that care. Be certain that all lubrication f ittings are assembled in place, using the lubrication illustration as a guide. Always lubricate the deck thoroughly before taking it to the field. Use a pressure lubricating gun ...

  • Cub Cadet 394 - page 19

    19 PRODUCT GRAPHICS Keep safety product gr aphics (decals) clean. Replace any safety graph ic that is damaged, destroyed, missing, painted over or can no longer be read. Replacemen t safety graphics ar e available throug h your dealer. HANDS AND FEET SAFETY GRAPHIC – LOCATED ON DEFLECTOR CHUTE KEEP HANDS AND FEET A WA Y FROM ROT A T ING P A RTS . ...

  • Cub Cadet 394 - page 20

    MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth below is given by Cub Cad et LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. Cub Cadet LLC warrants this product against defects for a period of two (2) years commencing on th e date of original purchase and will, a ...

メーカー Cub Cadet カテゴリー Lawn Mower

Cub Cadet 394のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 394の取扱説明書
- Cub Cadetの製品カード
- パンフレット
- またはCub Cadet 394の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cub Cadet 394の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cub Cadet 394の取り付け説明書、サービスマニュアル、簡易説明書、またはCub Cadet 394のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cub Cadet 394の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cub Cadet 394デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCub Cadet 394を使用するのを助ける技術的文書のことです。説明書は通常、全てのCub Cadet 394ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cub Cadetの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cub Cadet 394の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCub Cadet 394の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cub Cadet 394に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cub Cadet 394デバイスの基本機能を使うにあたってのヒント。 Cub Cadet 394のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cub Cadet 394に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCub Cadet 394のメーカー/サービスへの連絡先に関する情報。

Cub Cadet 394についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCub Cadet 394の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCub Cadet 394で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)