Bunn SRUの取扱説明書

36ページ 1.67 mb
ダウンロード

ページに移動 of 36

Summary
  • Bunn SRU - page 1

    OPERA TING & SER VICE MANU AL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 10067.0000F 8/00 ©1981 Bunn-O-Matic Corporation BU N N ® SR U SR U A ...

  • Bunn SRU - page 2

    Page 2 INTRODUCTION This brewer will brew a three gallon batch of coffee into the reservoir, which has its own dispensing faucet.The brewer also has a hot water faucet for allied beverage use. It is only for indoor use on a sturdy counter. W ARRANTY Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free fr ...

  • Bunn SRU - page 3

    Page 3 #00831.0000 #00656.0000 USER NOTICES Carefully read and follow all notices on the brewer and in this manual. They were written for your protection. All notices on the brewer are to be kept in good condition. Replace any unreadable or damaged labels. #00878.0000 #12593.0000 #03408.0000 #03409.0000 #12555.0000 10067 040100 #10044.0000 #29299.0 ...

  • Bunn SRU - page 4

    Page 4 ELECTRICAL REQUIREMENTS CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up. SRU Model requires 3- wire, grounded service rated 120/208 or 120/240 volts ac, 30 amp, single phase, 60 Hz. Proceed as follows: ELECTRICAL INSTALLATION INSTRUCTIONS CAUTION – Improper electrical installation can damag ...

  • Bunn SRU - page 5

    Page 5 INITIAL SETUP CAUTION - The brewer must be disconnected from the power source throughout the initial setup, except when specified in the instructions. IMPORTANT: Brewer must be level and installed on a sturdy structure. Electrician's and Plumber's Instructions are provided. These instructions should be carefully followed before pro ...

  • Bunn SRU - page 6

    Page 6 ADJUSTING BREW VOLUMES CAUTION - Disconnect the power source fr om the brewer prior to the removal of any panel for the replacement or adjustment of any component. NOTE: Prior to setting or modifying batch sizes, check that the brewer is connected to water supply , the tank is properly filled, and a funnel and ser ver are in place. 1. Modify ...

  • Bunn SRU - page 7

    Page 7 10067 080200 CLEANING NOTE: Tank and tank components should be delimed regularly based on local water conditions. Excessive mineral build up on stainless steel surfaces can initiate corrosion reactions resulting in serious leaks, 1. Remove funnel, funnel lid and support. Under hot water, rinse away all coffee oils. Wipe with a clean damp clo ...

  • Bunn SRU - page 8

    Page 8 PROBLEM Brew cycle will not start PROBABLE CAUSE 1. No water 2. No power or incorrect voltage to the brewer REMEDY Water lines and valves to the brewer must be open. (A1) Check the terminal block for 120 volts ac across the red and white terminals and the black and white terminal on three wire 102/ 208 volt or 120/240 volt models. (A2) Check ...

  • Bunn SRU - page 9

    Page 9 TROUBLESHOOTING (cont.) PROBLEM Brew cycle will not start (cont) Tank not filling PROBABLE CAUSE 3. Water level below pump housing. (Water level in the hot water gauge glass should be approximately half full). 4. ON/OFF Switch 5. Start Switch 6. Timer 7. Pump 8. Solenoid Valve 9. Strainer 1. ON/OFF Switch (This switch must be in the "ON ...

  • Bunn SRU - page 10

    Page 10 TROUBLESHOOTING (cont.) PROBLEM Water running out of the overflow Water is not hot PROBABLE CAUSE 1. Brewer not level 2. Solenoid Valve 3. Liquid Level Board 4. Probe 1. Limit Thermostat CAUTION - Do not eliminate or bypass limit thermostat. Use only Bunn-O-Matic replacement part #29329.1000. 2. Control Thermostat 3. Tank Heater(s) 4. Conta ...

  • Bunn SRU - page 11

    Page 11 PROBABLE CAUSE 1. Circuit Breaker 2. ON/OFF Switch 3. Brew Circuit 4. Refill Circuit 1. Timer 2. Start Switch 1. Timer 2. Solenoid Valve 3. Lime build-up in swing spout and pump tubing. 1. Filters 2. Hole in bottom of funnel obstructed. TROUBLESHOOTING (cont.) PROBLEM Circuit breaker keeps tripping Water keeps running from swing spout Incon ...

  • Bunn SRU - page 12

    Page 12 TROUBLESHOOTING (cont.) PROBLEM Funnel overflows (cont.) Coffee reservoir overflows Brewer is making unusal noises PROBABLE CAUSE REMEDY 3. Pump - Flow Rate 4. Soft Water 1. Coffee reservoir not completely empty before a brew cycle was started. 2. Timer 3. Pump - Flow Rate 1. Solenoid Valve 2. Plumbing lines 3. Water supply 4. Tank Heater(s ...

  • Bunn SRU - page 13

    Page 13 ...

  • Bunn SRU - page 14

    Page 14 SERVICE (cont.) CIRCUIT BREAKER (120/208V and 120/240V Three Wire Models) Location: The circuit breaker is located on the rear of the urn, behind the rear utility cover. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the black wire from the main harness from the circuit breaker and the white wire on the pump ...

  • Bunn SRU - page 15

    Page 15 SERVICE (cont.) Location: The contactor is located inside the front lower access panel, left of center on the component bracket. Test Procedures: 1. Disconnect the brewer from the power source. 2A. 120/208V and 120/240V THREE WIRE MODELS Disconnect the black wire from the contactor coil to the limit thermostat and black wire from the white ...

  • Bunn SRU - page 16

    Page 16 ...

  • Bunn SRU - page 17

    Page 17 SERVICE (cont.) CONTROL THERMOSTAT FIG. 6 CONTROL THERMOSTAT P2113.40 Location: The control thermostat is mounted on the left front of the top component bracket. Test Procedures: 1. Disconnect the brewer from the power source. 2. Locate the thermostat and the voltage check points. Model 120/208V & 120/240V - 3- wire w/ground single phas ...

  • Bunn SRU - page 18

    Page 18 SERVICE (cont.) FUSE AND FUSE HOLDER (208V, 240V and 230V Two Wire Models) Location: The fuse and fuse holder are located on the rear of the urn behind the rear utility cover. Test Procedures: 1. Disconnect the brewer from the power source. 2. Remove the cap and fuse from the fuse holder. 3. Remove fuse from the cap. 4. Check for continuity ...

  • Bunn SRU - page 19

    Page 19 LIMIT THERMOSTAT SERVICE (cont.) FIG. 11 LIMIT THERMOSTAT TERMINALS FIG. 10 LIMIT THERMOSTAT P1732 Location: The limit thermostat is located on the center rear of the component bracket behind the tank heater. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the black wires or the red wires from the limit thermo ...

  • Bunn SRU - page 20

    Page 20 SERVICE (cont.) LIQUID LEVEL BOARD AND LEVEL PROBE 5. Reconnect the blue wire to T1 on the liquid level board. 6. Carefully connect a piece of insulated jumper wire to T4. Keep the other end of this wire away from any metal surface of the brewer. 7. Touching the free end of the jumper to the brewer's frame simulates a "FULL" ...

  • Bunn SRU - page 21

    Page 21 SERVICE (cont.) LIQUID LEVEL BOARD AND LEVEL PROBE (cont.) T1 BLU to Solenoid Valve T2 BLK to ON/OFF Switch (All models except 230V-CE models- RED on CE Models) T3 WHI to Main Harness (120/208V and120/240V models) T3 RED to Main Harness (208V, 240V single phase and three phase models) T3 BLK to Main Harness (230V two wire models) T4 PIN to ...

  • Bunn SRU - page 22

    Page 22 10067 040100 ON/OFF SWITCH FIG.14 ON/OFF SWITCH P2053.25 Location: The ON/OFF switch is located on the left side of the lower front panel. Test Procedures: 1. Disconnect the brewer from the power source. 2. a)120/208V, 120/240V, 208V and 240V Models Remove the black wire on the ON/OFF switch from the fuse holder or circuit breaker and the r ...

  • Bunn SRU - page 23

    Page 23 SERVICE (cont.) PUMP ASSEMBLY FIG.16 PUMP ASSEMBLY P2113.40 Location: The pump is located on the right of the component bracket. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the black wire from the black lead on the pump and the white wire from the black lead on the pump. 3. With a voltmeter, check the volt ...

  • Bunn SRU - page 24

    Page 24 SERVICE (cont.) SELECTOR SWITCH (HALF BATCH OPTION) FIG. 18 SELECTOR SWITCH (HALF BATCH) P2053.25 Location: The selector switch is located in the center of the front access panel at the base of the urn on all models except the 230V CE Models. The selector switch is located to the right of the front panel, above the start switch on the 230V ...

  • Bunn SRU - page 25

    Page 25 SERVICE (cont.) SOLENOID FIG. 20 SOLENOID P2113.40 Location: The solenoid is mounted on the upper left rear of the component bracket. Test Procedures: 1. Disconnect the brewer from the power source. 2. A) For 120/208 volt and 120/240 volt 3-wire, single phase models, disconnect the black wire from the liquid level board #2 and the white wir ...

  • Bunn SRU - page 26

    Page 26 SERVICE (cont.) SOLENOID BLU from Liquid Level Board #1 WHI from Main Har- ness (120/208V and 120/240V Models) RED from Main Har- ness (208V and 240V Models) BLK from Main Harness BLU from Liquid Level Board #1 230V - CE MODELS FIG. 21 SOLENOID TERMINALS P1741.30 10. Install water inlet tube to connector on the sole- noid. 11. Turn on the w ...

  • Bunn SRU - page 27

    Page 27 START SWITCH (BREW) FIG. 22 START SWITCH (BREW) P2053.25 Location: The brew start switch is located on the lower right side of the front access panel at the base of the urn on all models except 230 volt CE. On 230 volt CE models, the start switch is located on the lower right of the front access panel, beneath the selector switch. Test Proc ...

  • Bunn SRU - page 28

    Page 28 BLK to Contactor T1 (All Models Except 230V-CE Models) BLK (Thermal Fuse) to T1 (230V-CE Models) RED to Contactor T2 (120/ 208V, 120/240 Three Wire Single Phase, 208V and 240V Two Wire, Single Phase) RED (Thermal Fuse) to T2 (230V-CE Models) SERVICE (cont.) TANK HEATERS P1746 FIG. 24 TANK HEATER P2113.40 Location: The tank heater is located ...

  • Bunn SRU - page 29

    Page 29 SERVICE (cont.) THERMAL FUSES (230V-CE MODELS ONLY) FIG. 26 THERMAL FUSES P2121.40 Location: The thermal fuses are mounted on the tank heater terminals. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the thermal fuse from the tank heater terminal and the contactor lead. 3. Check for continuity across the term ...

  • Bunn SRU - page 30

    Page 30 TIMER (Early Models) FIG. 27 TIMER P2114.40 Location: The timer is located behind the front access panel on the right side of the component bracket. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the polarized, three pin connector from the brewer main harness and rotate the brew timer dial fully counterclockw ...

  • Bunn SRU - page 31

    Page 31 SERVICE (cont.) TIMER (Early Models)(cont.) To Three Pin Female Connector on Main Harness BLK to Pump Lead WHI to Pump Lead Three Pin Connector from Half/Full Batch Switch FIG. 28 TIMER TERMINALS P1751 10067 080200 Removal and Replacement: 1. Separate all connectors between the brewer wir- ing harness and the timer. 2. Disconnect the timer ...

  • Bunn SRU - page 32

    Page 32 SERVICE (cont.) DIGITAL BREW TIMER (Late Models) ...

  • Bunn SRU - page 33

    Page 33 SERVICE (cont.) DIGITAL BREW TIMER (Late Models) 1. Modifying brew volumes. T o modify a brew vol- ume, first check that the SET/LOCK switch is in the “ SET ” position on the cir cuit board. T o increase a brew volume, place the ON/OFF switch in the “ ON ” position, press and hold the ST ART switch until you see three breaks in the ...

  • Bunn SRU - page 34

    Page 34 10067 080200 ...

  • Bunn SRU - page 35

    Page 35 10067 080200 ...

  • Bunn SRU - page 36

    Page 36 10067 080200 G 8 /BLK WHI/GRN WHI/BLU T1 T5 T3 T4 T2 ...

メーカー Bunn カテゴリー Coffeemaker

Bunn SRUのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SRUの取扱説明書
- Bunnの製品カード
- パンフレット
- またはBunn SRUの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bunn SRUの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bunn SRUの取り付け説明書、サービスマニュアル、簡易説明書、またはBunn SRUのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bunn SRUの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bunn SRUデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBunn SRUを使用するのを助ける技術的文書のことです。説明書は通常、全てのBunn SRUユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bunnの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bunn SRUの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBunn SRUの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bunn SRUに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bunn SRUデバイスの基本機能を使うにあたってのヒント。 Bunn SRUのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bunn SRUに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBunn SRUのメーカー/サービスへの連絡先に関する情報。

Bunn SRUについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBunn SRUの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBunn SRUで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)