Wagner SprayTech Model 9140の取扱説明書

52ページ 6.77 mb
ダウンロード

ページに移動 of 52

Summary
  • Wagner SprayTech Model 9140 - page 1

    English Printed in the U. S. A. M ODELS 9140, 9140S, 9150, 9170, 9190 AND 9210 H IGH P ERFORMANCE A IRLESS S PRA YER T ABLE OF C ONTENTS : SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 COMPONENTS AND DESCRIPTION . . . . . . . . . . . . . . . . . . 4 SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Wagner SprayTech Model 9140 - page 2

    HAZARD: INJECTION INJUR Y A high pressure paint stream produced by this equipment can pierce the skin and underlying tissues, leading to serious injury and possible amputation. SEE A PHYSICIAN IMMEDIA TEL Y . DO NOT TREA T AN INJECTION INJUR Y AS A SIMPLE CUT! Injection can lead to amputation. See a physician immediately . The maximum operating ran ...

  • Wagner SprayTech Model 9140 - page 3

    HAZARD: GENERAL Can cause severe injury or property damage. PREVENTION: • Read all instructions and safety precautions before operating equipment. • Follow all appropriate local, state, and national codes governing ventilation, fire prevention, and operation. • The United States Government Safety Standards have been adopted under the Occupati ...

  • Wagner SprayTech Model 9140 - page 4

    Spray gun Spray tip Spray hose Pail bracket Lubricating area (on front face plate) Hose bracket Handle Motor housing Return tube Suction tube Suction set screen ON/OFF switch O = OFF l = ON PRIME/ SPRA Y knob Fluid section O l SPRA Y PRIME SPRA Y PRIME PRIME/SPRA Y knob PRIME position SPRA Y position Customer Service: 800-880-0993 4 © 2003 W agner ...

  • Wagner SprayTech Model 9140 - page 5

    © 2003 W agner Spray T ech - All rights reserved. 5 Customer Service: 800-880-0993 English T OOLS N EEDED F OR S ETUP • T wo adjustable wrenches • 3/16” allen wrench • Extension cord (refer to Important Electrical Information (page 3) . Do not plug in the unit until setup is complete. A TT ACHING THE H ANDLE ( CART MODELS ) 1. Position the ...

  • Wagner SprayTech Model 9140 - page 6

    P LUGGING I N THE S PRA YER 1. Check that the ON/OFF switch is in the OFF position. 2. Plug the sprayer into a heavy duty grounded extension cord. Refer to Important Electrical Information, page 3). P RESSURE R ELIEF P ROCEDURE Be sure to follow the pressure relief procedure (page 6) when shutting the unit off FOR ANY PURPOSE. This procedure is use ...

  • Wagner SprayTech Model 9140 - page 7

    © 2003 W agner Spray T ech - All rights reserved. 7 Customer Service: 800-880-0993 English P URGING & P RIMING P URGING AND P RIMING THE P UMP 1. Place a full container of paint underneath the suction tube. 2. Secure the return tube into a waste container . 3. T urn the pressure control dial to maximum pressure (+). 4. T urn the PRIME/SPRA Y k ...

  • Wagner SprayTech Model 9140 - page 8

    P RACTICE Be sure that the paint hose is free of kinks and clear of objects with sharp cutting edges. 1. Switch the pump ON (l) and turn the PRIME/SPRA Y knob to SPRA Y . 2. T urn the pressure contol dial to its highest setting (+). The spray hose should stiffen as paint begins to flow through it. 3. When the motor shuts off, unlock the spray gun a ...

  • Wagner SprayTech Model 9140 - page 9

    © 2003 W agner Spray T ech - All rights reserved. 9 Customer Service: 800-880-0993 English U NCLOGGING THE S PRA Y T IP Do not attempt to unclog or clean the tip with your finger . Do not use a needle or other sharp pointed instrument to clean the tip. The hard tungsten carbide can chip. If the spray pattern becomes distorted or stops completely w ...

  • Wagner SprayTech Model 9140 - page 10

    I MPORT ANT C LEANING N OTES ! R EAD T HESE N OTES AND W ARNINGS B EFORE Y OU S T ART T O C LEAN Y OUR S PRA YER ! • When using latex paints, clean your sprayer and components using warm, soapy water . When using oil-based paints, use mineral spirits. • Do not use mineral spirits on latex paint, or the mixture will turn into a jelly-like substa ...

  • Wagner SprayTech Model 9140 - page 11

    © 2003 W agner Spray T ech - All rights reserved. 11 Customer Service: 800-880-0993 English C LEANUP ( CONTINUED ) 1. Make sure the pump is switched OFF (O), the PRIME/SPRA Y knob is turned to PRIME, and unplug the sprayer . 2. Remove spray gun from the paint hose using adjustable wrenches. 3. Remove filter from spray gun (refer to Cleaning the Sp ...

  • Wagner SprayTech Model 9140 - page 12

    S HORT -T ERM S T ORAGE ( UP T O 16 HOURS ) S HUTDOWN 1. Lock the spray gun off. 2. T urn the PRIME/SPRA Y knob to PRIME. 3. Switch the pump OFF , and unplug the sprayer . 4. Pour 1/2 cup water slowly on the top of the paint to prevent the paint from drying. 5. Wrap the spray gun assembly in a damp cloth and place it in a plastic bag. Seal the bag ...

  • Wagner SprayTech Model 9140 - page 13

    © 2003 W agner Spray T ech - All rights reserved. 13 Customer Service: 800-880-0993 English D AIL Y M AINTENANCE The only daily maintenance necessary is thorough cleaning. Follow the cleaning procedures in this manual. E XTENDED M AINTENANCE Some pump parts eventually wear out from use and must be replaced. The following list indicates the availab ...

  • Wagner SprayTech Model 9140 - page 14

    Customer Service: 800-880-0993 14 © 2003 W agner Spray T ech - All rights reserved. English D ISASSEMBL Y OF THE F LUID S ECTION 1. Remove the suction set. 2. Remove the front cover and the four screws that secure it using a T20 T orx head driver . 3. Remove the yoke screw and washer that secures the dowel pin. The dowel pin connects the yoke to t ...

  • Wagner SprayTech Model 9140 - page 15

    © 2003 W agner Spray T ech - All rights reserved. 15 Customer Service: 800-880-0993 English T ROUBLESHOOTING P ROBLEM A. The sprayer does not start. B. The sprayer starts but does not draw in paint when the PRIME/SPRA Y knob is set to PRIME. C. The sprayer draws up paint but the pressure drops when the gun is triggered. D. The PRIME/SPRA Y valve i ...

  • Wagner SprayTech Model 9140 - page 16

    ...

  • Wagner SprayTech Model 9140 - page 17

    Français Impression aux É.-U. P UL VÉRISA TEUR SANS AIR PERFORMANT , MODÈLES 9140, 9140S, 9150, 9170, 9190 ET 9210 M ANUEL DE L ’ UTILISA TEUR • L IRE CE MANUEL POUR OBTENIR DES DIRECTIVES COMPLÈTES T ABLE DES MA TIÈRES : SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19 DESCRIPTION ET COMPOSANTS . . . . ...

  • Wagner SprayTech Model 9140 - page 18

    DANGER : INJECTION CUT AN É E Le jet de haute pression produit par cet appareil peut transpercer la peau et les tissus sous- jacents, causant des blessures graves pouvant aller jusqu ’à l ’ amputation. NE P AS TRAITER CE TYPE DE BLESSURE COMME UNE SIMPLE COUPURE! Une amputation peut en r é sulter . ON DOIT CONSUL TER UN M É DICIN SUR-LE-CHA ...

  • Wagner SprayTech Model 9140 - page 19

    DANGER : G É N É RALIT É S D ’ autres dangers peuvent entra î ner des dommages mat é riels ou des blessures graves. MESURES PR É VENTIVES : • Lire toutes les directives et consignes de s é curit é avant d ’ utiliser l ’ appareil. • Observer tous les codes locaux, provinciaux, d ’é tat et nationaux r é gissant la ventilation, l ...

  • Wagner SprayTech Model 9140 - page 20

    C OMPOSANTS Le carton d ’ exp é dition de cet appareil contient les é l é ments suivants : • un dispositif d ’ aspiration et un tube de retour; • un pistolet muni d ’ un filtre; • un embout et ses composants (se reporter au tableau ci-dessous); • un flexible haute pression d ’ un diam è tre de 0,6 centim è tre, long de 7,6 m è ...

  • Wagner SprayTech Model 9140 - page 21

    O UTILS R EQUIS • Deux clés à molette • Une clé hexagonale (0,475 cm) • Une rallonge (se reporter à la section RENSEIGNEMENTS IMPORT ANTS SUR L ’ÉLECTRICITÉ , page 19). Ne pas brancher le pulvérisateur avant d’avoir terminé les préparatifs. F IXA TION DU GUIDON ( MODÈLES DU CHARIOT ) 1. Placer le guidon contre le chariot de mani ...

  • Wagner SprayTech Model 9140 - page 22

    B RANCHEMENT DU PUL V É RISA TEUR 1. Mettre l ’ interrupteur hors tension (O). 2. Brancher le pulv é risateur dans une rallonge trifilaire de service robuste. Se reporter à la section RENSEIGNEMENTS IMPORT ANTS SUR L ’É LECTRICIT É , page 19. D É COMPRESSION S ’ assurer de suivre cette proc é dure pour rel â cher la pression à l ’ ...

  • Wagner SprayTech Model 9140 - page 23

    P URGE ET AMOR Ç AGE DE LA POMPE 1. Mettre un contenant plein de produit sous le tube d ’ aspiration. 2. Fixer le tube de retour à un contenant de vidange. 3. T ourner le bouton de r é gulation de la pression jusqu ’ au maximum (+). 4. R é gler le bouton PRIME/SPRA Y à PRIME. 5. Brancher le pulv é risateur et mettre l ’ interrupteur sou ...

  • Wagner SprayTech Model 9140 - page 24

    E SSAIS S ’ assurer que le flexible n ’ est ni pli é ni en contact avec des ar ê tes coupantes. 1. Mettre l ’ interrupteur sous tension (l) et r é gler le bouton PRIME/SPRA Y à SPRA Y . 2. T ourner le bouton de r é gulation de la pression jusqu ’ au maximum (+). Le flexible devrait se raidir sous l ’ effet du produit qui commence à ...

  • Wagner SprayTech Model 9140 - page 25

    N ETT OY AGE DE L ’ EMBOUT DE PUL V É RISA TION Ne pas tenter de d é bloquer ou de nettoyer l ’ embout avec le doigt. Ne pas utiliser une aiguille ou un instrument pointu pour nettoyer l ’ embout; le carbure de tungst è ne pourrait s ’é cailler . Si le jet se d é forme ou s ’ arr ê te compl è tement alors qu ’ on serre la d é te ...

  • Wagner SprayTech Model 9140 - page 26

    26 800-880-0993 © 2003 W agner Spray T ech - T ous droits r é serv é s. Fran ç ais N ETT OY AGE R EMARQUES IMPORT ANTES AU SUJET DU NETT OY AGE L IRE LES REMARQUES ET MISES IN GARDE SUIV ANTES A V ANT DE NETTOYER LE PUL V É RISA TEUR ! • En pr é sence de produits au latex, on doit se servir d ’ eau ti è de savonneuse pour nettoyer le pul ...

  • Wagner SprayTech Model 9140 - page 27

    1. S ’ assurer que l ’ interrupteur est hors tension (O) et que le bouton PRIME/SPRA Y est r é gl é à PRIME, puis d é brancher le pulv é risateur . 2. D é tacher le pistolet du flexible de pulv é risation au moyen de cl é s à molette. 3. Retirer le filtre du pistolet (se reporter à la section NETTOY AGE DU FIL TRE DE PISTOLET , page 2 ...

  • Wagner SprayTech Model 9140 - page 28

    R ANGEMENT À COURT TERME ( JUSQU ’ À 16 HEURES ) P R É P ARA TION POUR LE RANGEMENT 1. V errouiller le pistolet. 2. T ourner le bouton PRIME/SPRA Y à la position PRIME. 3. Mettre l ’ interrupteur hors tension (O), puis d é brancher le pulv é risateur . 4. V erser lentement-tasse d ’ eau à la surface du produit, pour l ’ emp ê cher d ...

  • Wagner SprayTech Model 9140 - page 29

    E NTRETIEN QUOTIDIEN Le seul entretien à effectuer r é guli è rement est le nettoyage en profondeur; pour ce faire, suivre les directives apparaissant au pr é sent manuel. M AINTENANCE À LONG TERME Certaines pi è ces s ’ usent avec le temps et doivent ê tre remplac é es. La liste suivante é num è re les trousses de r é paration of fert ...

  • Wagner SprayTech Model 9140 - page 30

    30 800-880-0993 © 2003 W agner Spray T ech - T ous droits r é serv é s. Fran ç ais D É SASSEMBLAGE DU TRON Ç ON 1. Retirer le dispositif d ’ aspiration. 2. Retirer le couvercle avant en enlevant les quatre vis qui le retiennent au moyen d ’ un tournevis à pointe hexalob é e (T orx T20). 3. Retirer la vis de chape et la rondelle qui reti ...

  • Wagner SprayTech Model 9140 - page 31

    © 2003 W agner Spray T ech - T ous droits r é serv é s. 800-880-0993 31 Fran ç ais D É P ANNAGE P ROBL È MES A. Le pulv é risateur ne d é marre pas. B. Le pulv é risateur d é marre, mais n ’ aspire pas le produit quand le bouton PRIME/SPRA Y est à PRIME. C. Le pulv é risateur aspire le produit, mais la pression chute d è s qu ’ on ...

  • Wagner SprayTech Model 9140 - page 32

    ...

  • Wagner SprayTech Model 9140 - page 33

    Español Impreso en los EE.UU. M ODELOS 9140, 9140S, 9150, 9170, 9190, Y 9210 R OCIADOR SIN AIRE DE AL T O RENDIMIENT O M ANUAL DEL USARIO • L EA ESTE MANUAL P ARA OBTENER LAS INSTRUCCIONES COMPLET AS C ONTENIDO : SEGURIDAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-35 COMPONENTES Y DESCRIPCIÓN . . . . . . . . . . . . . ...

  • Wagner SprayTech Model 9140 - page 34

    Espa ñ ol PELIGRO: LESI Ó N POR INYECCI Ó N El flujo de pintura a alta presi ó n que produce este equipo puede perforar la piel y los tejidos subyacentes, ocasionando lesiones graves y posible amputaci ó n. CONSUL TE A UN M É DICO INMEDIA T AMENTE. ¡ NO TRA TE LA LESI Ó N POR INYECCI Ó N COMO UNA CORT ADURA SIMPLE! La inyecci ó n puede oc ...

  • Wagner SprayTech Model 9140 - page 35

    Espa ñ ol I NSTRUCCIONES P ARA LA CONEXI Ó N A TIERRA Este producto debe conectarse a tierra. En caso de un cortocircuito el é ctrico, la conexi ó n a tierra reduce el riesgo de choque el é ctrico al aportar un alambre de escape para la corriente el é ctrica. Este producto est á equipado con un cable que tiene alambre a tierra con un enchufe ...

  • Wagner SprayTech Model 9140 - page 36

    1-800-880-0993 36 © 2003 W agner Spray T ech - T odos los derechos reservados. Espa ñ ol C OMPONENTES Y D ESCRIPCI Ó N Pistola rociadora Boquilla rociadora Manguera rociadora Soporte para el bote Á rea de lubricaci ó n (en la placa frontal) Soporte de la manguera Mango Alojamiento del motor T ubo de retorno T ubo de succi ó n Malla del juego ...

  • Wagner SprayTech Model 9140 - page 37

    © 2003 W agner Spray T ech - T odos los derechos reservados. 37 1-800-880-0993 Español H ERRAMIENT AS NECESARIAS P ARA LA PREP ARACIÓN • Dos llaves ajustables • Llave Allen de 3/16" (4.8 mm) • Cable de extensión (consulte la Información eléctrica importante página 35 ). No enchufe la unidad hasta que termine la preparación. I NST ...

  • Wagner SprayTech Model 9140 - page 38

    1-800-880-0993 38 © 2003 W agner Spray T ech - T odos los derechos reservados. Espa ñ ol C Ó MO ENCHUF AR EL ROCIADOR 1. F í jese que el interruptor de encendido/apagado est é en la posici ó n de apagado (O). 2. Enchufe el rociador en un cable de extensi ó n conectado a tierra y de calibre adecuado. Consulte la Informaci ó n el é ctrica im ...

  • Wagner SprayTech Model 9140 - page 39

    © 2003 W agner Spray T ech - T odos los derechos reservados. 39 1-800-880-0993 Espa ñ ol P URGA Y CEBADO DE LA BOMBA 1. Coloque el tubo de succi ó n dentro de un bote de pintura. 2. Sujete el tubo de retorno dentro de un recipiente de desecho. 3. Gire el selector de control de presi ó n al m á ximo (+). 4. Gire la perilla PRIME/ SPRA Y a PRIME ...

  • Wagner SprayTech Model 9140 - page 40

    1-800-880-0993 40 © 2003 W agner Spray T ech - T odos los derechos reservados. Espa ñ ol P R Á CTICA Revise que la manguera de pintura no tenga dobleces y est é alejada de objetos con bordes cortantes. 1. Encienda (l) la bomba y gire la perilla PRIME/ SPRA Y a SPRA Y . 2. Gire el selector de control de presi ó n al m á ximo (+). La manguera r ...

  • Wagner SprayTech Model 9140 - page 41

    © 2003 W agner Spray T ech - T odos los derechos reservados. 41 1-800-880-0993 Espa ñ ol D ESBLOQUEO DE LA BOQUILLA ROCIADORA No intente desbloquear o limpiar la boquilla con el dedo. No use agujas ni otros instrumentos punzantes afilados para limpiar la boquilla. Puede picarse el carburo de tungsteno duro. Si se distorsiona el patr ó n de rocia ...

  • Wagner SprayTech Model 9140 - page 42

    1-800-880-0993 42 © 2003 W agner Spray T ech - T odos los derechos reservados. Espa ñ ol L IMPIEZA ¡ N OT AS IMPORT ANTES DE LIMPIEZA ! ¡ L EA EST AS NOT AS Y ADVERTENCIAS ANTES DE COMENZAR A LIMPIAR EL ROCIADOR ! • Al usar pinturas l á tex, limpie el rociador y los componentes con agua jabonosa tibia. Al usar pinturas con aceite, use alcoho ...

  • Wagner SprayTech Model 9140 - page 43

    © 2003 W agner Spray T ech - T odos los derechos reservados. 43 1-800-880-0993 Espa ñ ol 1. Revise que la bomba est é apagada (O), que la perilla PRIME/ SPRA Y est é en PRIME y desenchufe el rociador . 2. Separe la pistola rociadora de la manguera de pintura usando llaves ajustables. 3. Retire el filtro de la pistola rociadora (consulte Limpiez ...

  • Wagner SprayTech Model 9140 - page 44

    1-800-880-0993 44 © 2003 W agner Spray T ech - T odos los derechos reservados. Espa ñ ol A LMACENAMIENT O DE CORT O PLAZO ( HAST A 16 HORAS ) P ARO 1. Bloquee el gatillo de la pistola. 2. Gire la perilla PRIME/SPRA Y hasta la posici ó n PRIME. 3. Mueva el interruptor principal a la posici ó n AP AGADO (O) y desenchufe el rociador . 4. Para los ...

  • Wagner SprayTech Model 9140 - page 45

    © 2003 W agner Spray T ech - T odos los derechos reservados. 45 1-800-880-0993 Espa ñ ol M ANTENIMIENT O DIARIO El ú nico mantenimiento diario necesario es la limpieza a fondo. Siga los procedimientos de limpieza de este manual. M ANTENIMIENT O A LARGO PLAZO Algunas piezas de la bomba se desgastan finalmente con el uso y deben cambiarse. La list ...

  • Wagner SprayTech Model 9140 - page 46

    1-800-880-0993 46 © 2003 W agner Spray T ech - T odos los derechos reservados. Espa ñ ol D ESMONT AJE DE LA SECCI Ó N DE FLUIDOS 1. Retire el juego de succi ó n. 2. Retire la cubierta delantera y los cuatro tornillos que la aseguran usando una herramienta de cabeza T20 T orx. 3. Quite el tornillo de horquilla y la arandela que asegura la clavij ...

  • Wagner SprayTech Model 9140 - page 47

    © 2003 W agner Spray T ech - T odos los derechos reservados. 47 1-800-880-0993 Espa ñ ol S OLUCI Ó N DE PROBLEMAS P ROBLEMA A. El rociador no arranca. B. El rociador arranca pero no aspira pintura cuando se pone la perilla PRIME/ SPRA Y (CEBAR/ROCIAR) en CEBAR. C. El rociador extrae pintura pero la presi ó n baja cuando se acciona la pistola. D ...

  • Wagner SprayTech Model 9140 - page 48

    English 48 800-880-0993 © 2003 W agner Spray T ech - All rights reserved. Fran ç ais Espa ñ ol GX-06/07 (9140, 9140S, 9150, 9170) Item Part # Description Quantity 1 0512120 Plastic gun assembly ............................1 0512121 Metal gun assembly ..............................1 2 050101 1 Guard Assembly ...................................1 3 ...

  • Wagner SprayTech Model 9140 - page 49

    English Fran ç ais © 2003 W agner Spray T ech - All rights reserved. 800-880-0993 49 Espa ñ ol Article N ° de pi è ce Description Quantity 1 Se reporter à la liste d ’ ACCESSOIRES 2 050101 1 Prot è ge-embout ....................................1 3 0296261 Diffuseur , 2,2 cm ...................................1 4 0296270 Ressort de soupape ...

  • Wagner SprayTech Model 9140 - page 50

    English 50 800-880-0993 © 2003 W agner Spray T ech - All rights reserved. Fran ç ais Espa ñ ol P ARTS LIST • L ISTE DE PI È CES • L IST A DE PIEZAS GX-10 (9210) Item Part # Description Quantity 1 Refer to Accessories, page 13 2 050101 1 Holder assembly ...................................1 3 0296261 Diffuser , 7/8" ..................... ...

  • Wagner SprayTech Model 9140 - page 51

    English Fran ç ais © 2003 W agner Spray T ech - All rights reserved. 800-880-0993 51 Espa ñ ol 8 0512396 Roue (9140, 9150) . . . . . . . . . . . . . .2 0512397 Roue (9170) . . . . . . . . . . . . . . . . . . .2 0278373 Roue (9190, 9210) . . . . . . . . . . . . . .2 9 0275728 Capuchon (9140, 9150, 9170) . . . . . .2 9890104 Capuchon (9190, 9210) ...

  • Wagner SprayTech Model 9140 - page 52

    English 52 800-880-0993 © 2003 W agner Spray T ech - All rights reserved. Fran ç ais Espa ñ ol GARANTIE LIMIT É E MA T É RIEL DE PUL V É RISA TION DE PEINTURE SANS AIR Ce produit, fabriqu é par W agner Spray T ech Corporation (Wagner), est garanti, au b é n é fice de l ’ acheteur au d é tail d ’ origine, contre tout vice de mati è re ...

メーカー Wagner SprayTech カテゴリー Paint Sprayer

Wagner SprayTech Model 9140のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Model 9140の取扱説明書
- Wagner SprayTechの製品カード
- パンフレット
- またはWagner SprayTech Model 9140の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Wagner SprayTech Model 9140の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Wagner SprayTech Model 9140の取り付け説明書、サービスマニュアル、簡易説明書、またはWagner SprayTech Model 9140のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Wagner SprayTech Model 9140の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Wagner SprayTech Model 9140デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWagner SprayTech Model 9140を使用するのを助ける技術的文書のことです。説明書は通常、全てのWagner SprayTech Model 9140ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Wagner SprayTechの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Wagner SprayTech Model 9140の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWagner SprayTech Model 9140の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Wagner SprayTech Model 9140に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Wagner SprayTech Model 9140デバイスの基本機能を使うにあたってのヒント。 Wagner SprayTech Model 9140のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Wagner SprayTech Model 9140に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWagner SprayTech Model 9140のメーカー/サービスへの連絡先に関する情報。

Wagner SprayTech Model 9140についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWagner SprayTech Model 9140の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWagner SprayTech Model 9140で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)