Hobart C88A ML-110041の取扱説明書

28ページ 1.57 mb
ダウンロード

ページに移動 of 28

Summary
  • Hobart C88A ML-110041 - page 1

    C-LINE A & A W DISHW ASHERS MODEL R- L OPERATION L-R OPERATION C44A ML-38898 ML-38899 ML-104047 ML-104050 C44AW ML-103946 ML-103947 ML-104082 ML-104083 C54A ML-104199 ML-104198 C64A ML-103908 ML-103909 C88A ML-110042 ML-110041 CRS66A ML-38947 ML-38948 ML-104052 ML-104055 CRS66AW ML-103958 ML-103959 ML-104086 ML-104087 CRS76A ML-104202 ML-104201 ...

  • Hobart C88A ML-110041 - page 2

    – 2 – IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OB ...

  • Hobart C88A ML-110041 - page 3

    – 3 – TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Standard Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Optional Equipment . . . . . . . . . . . . . . ...

  • Hobart C88A ML-110041 - page 4

    – 4 – Installation, Operation and Care Of C-LINE A & A W DISHW ASHERS SA VE THESE INSTRUCTIONS GENERAL C-Line A or AW Dishwashers are fully automatic, rack-type washers that convey the rack from one end of the machine to the other, exposing the ware to progressive wash/rinse action. It has a stainless steel tank and chamber with a welded st ...

  • Hobart C88A ML-110041 - page 5

    – 5 – STANDARD EQUIPMENT Controls (Fig. 1) Fig. 1 The controls are mounted on top of the chamber. There are three operational control switches housed in the control box: Power (ON-OFF); Motor (ON-OFF); and Timer (MANUAL-AUTO). A pilot circuit transformer provides a reduced voltage of 115 volts for the machine controls. When equipped for gas hea ...

  • Hobart C88A ML-110041 - page 6

    – 6 – Thermometers Dial thermometers for wash and final rinse are indicated in ° F and ° C on the faceplate. Door Interlocks Door interlock switches will prevent machine operation while an inspection door is open. If a door is opened while the machine is operating, the pumps and conveyor will automatically turn off. After the door is closed, ...

  • Hobart C88A ML-110041 - page 7

    – 7 – OPTIONAL EQUIPMENT Blower Dryer — Dishes are dried by forced, heated air (3-phase machines only). The exhaust requirement at the vent stack of the blower dryer is 1400 CFM. Conveyor Dwell — The optional conveyor dwell switch (Conveyor ON-OFF) is housed in the control box and shuts the conveyor drive motor off. Condenser — Removes ex ...

  • Hobart C88A ML-110041 - page 8

    – 8 – INST ALLA TION UNPACKING Immediately after unpacking the dishwasher, check it for possible shipping damage. If the machine is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, verify that the electrical service agrees with the specifications on the machine data plat ...

  • Hobart C88A ML-110041 - page 9

    – 9 – ASSEMBLY Dish tables should be fitted into the dishwasher (Fig. 2). Use mastic between table and lip of tank to prevent leakage. Rack track height should be from 1 / 4 to 5 / 16 " (Fig. 2) above the tank lip. Dish tables should be sloped so that any water carried from the dishwasher will drain back into it. Fig. 2 Remove the strainer ...

  • Hobart C88A ML-110041 - page 10

    – 10 – WATER REQUIREMENTS Proper water quality can improve ware washing performance by reducing spotting, lowering chemical supply costs, enhancing effectiveness of labor and extending equipment life. Local water conditions vary from one location to another. The recommended proper water treatment for effective and efficient use of this equipmen ...

  • Hobart C88A ML-110041 - page 11

    – 11 – FILL & FINAL RINSE CONNECTION (Fig. 5) Fig. 5 Use 3 / 4 " pipe for the connecting line. A flowing pressure of 15 to 25 psig and a minimum temperature of 180 ° F must be maintained at the machine for common water connection for a non-booster heat machine; 110 ° F minimum temperature incoming water is required for machines equip ...

  • Hobart C88A ML-110041 - page 12

    – 12 – GAS CONNECTION (WHEN EQUIPPED) Check the gas data plate attached to the dishwasher or tag attached to the gas burner tubing for type of gas to be used. The burner is not adjustable. If flowing gas pressure is above 7" W.C. (natural gas) or 11" W.C. (propane gas), an additional regulator valve (not supplied) must be installed in ...

  • Hobart C88A ML-110041 - page 13

    – 13 – VENTING REQUIREMENTS Type II Canopy Hood Most commercial dishwashers must be provided with external venting per local codes. The exception is electric or steam heat machines operating in the chemical or low temperature sanitizing mode where the existing room ventilation will compensate for the vapors produced. The local authority has fin ...

  • Hobart C88A ML-110041 - page 14

    – 14 – PANT-LEG VENT CONNECTIONS (Figs. 7, 8) IMPORTANT : Gas heat machines must be provided with a means to exhaust the flue gases to the exterior of the building. Pant-Leg duct connectors (Fig. 7) alone DO NOT provide ventilation for the gas flue at the rear of the machine. A mini vent hood (Fig. 8) must be used or a canopy type hood may be u ...

  • Hobart C88A ML-110041 - page 15

    – 15 – If using the 'Pant-Leg' duct, a mini vent hood (Fig. 8), positioned about 18" above the flue exit at the rear of the dishwasher and connected to existing duct work, must be used for the flue gases. The volume of flue exhaust in the mini vent hood should not exceed 200 CFM. Fig. 8 In either case, if a powered means of exhau ...

  • Hobart C88A ML-110041 - page 16

    – 16 – RATE OF EXHAUST FLOW CALCULATIONS Based on the 2004 International Mechanical Code (IMC). The Rate of air flow required for a vent hood is now based on the linear length of the face of the hood instead of the area of the hood opening. The length of the hood is measured along the front side that is parallel with the front line of the appli ...

  • Hobart C88A ML-110041 - page 17

    – 17 – ELECTRICAL CONNECTIONS — DISHWASHER WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE ANSI / NFPA 70 (LATEST EDITION) AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. THERE MAY BE MU ...

  • Hobart C88A ML-110041 - page 18

    – 18 – ELECTRICAL CONNECTIONS — OPTIONAL EQUIPMENT WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. OPTIONAL EQUIPMENT CONTROL CONNECTIONS ...

  • Hobart C88A ML-110041 - page 19

    – 19 – CURTAIN INSTALLATION ...

  • Hobart C88A ML-110041 - page 20

    – 20 – OPERA TION PREPARATION Put the dishwasher strainer pans and strainer basket (Fig. 3) into position in each dishwasher tank. If the machine is equipped with an RS, CS, or PW unit, install the solid prewash strainer pan over the overflow tube, flange side down and the lip toward the rear of the tank. Install one perforated strainer pan, ha ...

  • Hobart C88A ML-110041 - page 21

    – 21 – If the machine is equipped with gas heat, refer to STARTING THE GAS HEAT DISHWASHER below. The tank water temperature is regulated by the solid-state thermostat. The thermostat is preset at the factory and no adjustment should be required. If an adjustment is necessary or the machine is to operate low temperature, contact your local Hoba ...

  • Hobart C88A ML-110041 - page 22

    – 22 – DISHWASHING After the machine has filled, start pumps by pushing the Motor switch ON (Fig.1). Prescrap dishes thoroughly to remove large food particles and debris. Never use steel wool on ware that is to be loaded into the dishwasher. Stack dishes in the racks. Do not stack dishes one on top of another, as water must have free access to ...

  • Hobart C88A ML-110041 - page 23

    – 23 – CLEANING The machine must be thoroughly cleaned at the end of each working shift, or at least twice a day. Use only products formulated to be safe on stainless steel. 1. Turn the Motor and Power switches OFF . 2. Open the door(s). Standard door interlock switches prevent machine operation with inspection door(s) open. 3. Check the upper ...

  • Hobart C88A ML-110041 - page 24

    – 24 – 13 . Thoroughly wash out the interior of the machine with a heavy-duty hose fitted with a squeeze valve. Remove remaining soil with a cloth or soft brush and mild cleanser. Rinse again with hose. Do not allow food soil to accumulate on the bottom of the tank. 14. Return all strainer pans, strainer basket(s) and the pump intake strainer t ...

  • Hobart C88A ML-110041 - page 25

    – 25 – MAINTENANCE WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. Some machines may have more than one electrical power supply. All supplies MUST be disconnected. VENT When cool, check the vent of this dishwasher every six months for obstructions. LUBRICATION None required. SERVICE Contact your l ...

  • Hobart C88A ML-110041 - page 26

    – 26 – TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE No Machine Operation. 1. Blown fuse or tripped circuit breaker at power supply. 2. Inspection door(s) not closed. 3. Conveyor jammed. 4. If Auto Timer was used, the timer may have timed out. 5. If table limit switch is used, the switch may be tripped. 6. Manual overload protector tripped on pump mot ...

  • Hobart C88A ML-110041 - page 27

    – 27 – SYMPTOM POSSIBLE CAUSE Inadequate Rinse. 1. Dirty line strainer (Fig. 5) causing reduced water flow. Turn off water supply, remove strainer cap and withdraw and clean screen. Reassemble. 2. Low supply line pressure. 3. Clogged rinse nozzle(s). Continuous Rinse 1. Rinse actuator (Fig. 16) not moving freely. Operation. DISCONNECT THE ELECT ...

  • Hobart C88A ML-110041 - page 28

    NOTES – 28 – FORM 17791 Rev. O (Feb. 2006) PRINTED IN U.S.A. ...

メーカー Hobart カテゴリー Dishwasher

Hobart C88A ML-110041のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- C88A ML-110041の取扱説明書
- Hobartの製品カード
- パンフレット
- またはHobart C88A ML-110041の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Hobart C88A ML-110041の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Hobart C88A ML-110041の取り付け説明書、サービスマニュアル、簡易説明書、またはHobart C88A ML-110041のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Hobart C88A ML-110041の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Hobart C88A ML-110041デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHobart C88A ML-110041を使用するのを助ける技術的文書のことです。説明書は通常、全てのHobart C88A ML-110041ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Hobartの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Hobart C88A ML-110041の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHobart C88A ML-110041の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Hobart C88A ML-110041に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Hobart C88A ML-110041デバイスの基本機能を使うにあたってのヒント。 Hobart C88A ML-110041のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Hobart C88A ML-110041に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHobart C88A ML-110041のメーカー/サービスへの連絡先に関する情報。

Hobart C88A ML-110041についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHobart C88A ML-110041の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHobart C88A ML-110041で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)