Makita EBH340Rの取扱説明書

24ページ 0.69 mb
ダウンロード

ページに移動 of 24

Summary
  • Makita EBH340R - page 1

    Bac kpac k Br ushCutter INSTRUCTION MANU AL EBH340R Warning Read this instruction manual care fully before putting the B rush Cutter into operation and strictly observe the safety regul atio ns! Preserve instruction manual car efully! EBH340R ...

  • Makita EBH340R - page 2

    2 Thank you very much for sele cting the MA KIT A Brush Cutter . We are pleased to be able to you the MAKITA B rush Cutt er which is the result of a long development programme and man y years of knowledge and experience. Please rea d, understand and follow this bo oklet which refers in detail to the various points that will dem onstrate its o utsta ...

  • Makita EBH340R - page 3

    3 SAFETY INSTRUCTIONS Genera l Instru ctions – T o ensur e corre ct and s afe ope ratio n, the us er must read, underst and and f ollow this instructi on manual to assure familia rity with the handl ing of th e brush cu tter . Users insuff i- ciently informed will risk danger to themselve s as we ll as othe rs due to improper handling. – It is ...

  • Makita EBH340R - page 4

    4 Start the brush cutter only in accor dance with the ins tructions. Do not use any othe r methods for startin g the engine! – Use the brush cut ter and the tools supplied on ly for applicat ions specified. – Start the brush cutter en gine only after the entire tool has been assembled. Operation of the tool is permitted on ly after all the appr ...

  • Makita EBH340R - page 5

    5 Meth od of ope ration – Use the brush cutter only in good light and visibility . During cold seasons beware of slipp ery or wet areas, i ce and snow (ri sk of slipping). Always ensure a safe footing. – Do not o verreach . Keep pr oper foot ing, ba lance a nd hand control of the unit at all times. – Never cut above waist level. – Never sta ...

  • Makita EBH340R - page 6

    6 Never st raight en or weld dama ged cutti ng blade s. – Be kind to the en vironmen t. Operate the brush cutter wit h as little noise and pollution as possible. In part icular check the correct adjustment of the carbur etor . – Clean the br ush cutter at regular int ervals and ch eck that all screws and nuts are securely tig htened. – Never ...

  • Makita EBH340R - page 7

    7 TECHNICAL D A T A 1 ) This data takes equ ally int o account id ling and full sp eed or wide open thr ottle op erating mode s. Model EBH340R Loop handle Dimensions : length x width x height (without pipe ca se length) mm 400 x 325 x 395 Mass (without guard and cut ting blade) kg 9.8 V olume (fuel t ank) L 0.65 Cutting atta chments ( cutter blade ...

  • Makita EBH340R - page 8

    8 DESIGNA TION OF P ARTS Ԣ ԛ ԣ Ԟ Ԥ Ԡ Ԝ ԡ ԟ Ԩ ԩ ԝ Ԙ Ԧ ԙ Ԛ ԧ Ԫ ԫ GB DESIGNA TION OF P ARTS 1 Fuel T ank 2 Rewind St arter 3 Air Cleaner 4 I-O Switch (on/off) 5 Sp ark P lug 6 Exhaust M uffler 7 Handle 8 Control Lever 9 Control Cable 10 Shaft 1 1 P rotector 12 Gear Cas e/Head Cas e 13 Cutter Blade 14 Shoulder Strap 15 Fuel Filter Ca ...

  • Makita EBH340R - page 9

    9 C A UT I O N : Before perf orming any wor k on t he brush cutter , always switch off the motor and pull the spark plug connectors off t he spark plu g. Beware of hot engine pars and sharp blade edges. Always wea r protective g loves! CA UTI O N : Start the brush cutter only after having as- sembled it completely . 1. Joining flexible pipe with en ...

  • Makita EBH340R - page 10

    10 CONNECTION OF SWITCH CORD – Connect the switch cord s to the two cords from the engine by inserting one into the other. – Fix the co rd connecto r by clamp (7). ADJUS TMEN T OF CO NTROL CABLE – Adjust the control cable by a djusting bolt so t hat it will have 1 to 2 mm p lay when the thro ttle le ver is set to the l ow-speed positi on by c ...

  • Makita EBH340R - page 11

    11 MOUNTIN G OF HANDLE – Fix t he loop handle to the dr ive sh aft by 2 b olts firml y . – Do not ad just position of the loop hand le too close to the cont rol grip. Kee p not less than 25 cm distanc e betwee n the hand le and the grip. MOUNTING OF PR O TECT OR T o meet the applica ble safety provisio ns, only the tool/pr otector combinations ...

  • Makita EBH340R - page 12

    12 Inspection and Refill of Engine Oil – Perform the follow ing procedure, with the e ngine cooled down. – While keeping the engine level, remove the oil gauge, and confir m that the oil is filled within the upper and lower limit marks . When the oil is in short in such a way that the oil gauge touches the oil only by its tip, in particular wit ...

  • Makita EBH340R - page 13

    13 Handli ng of Fuel It is nece ssary to handle fuel with utmost care . Fuel may contain substan ces s imilar to s olvents . Refuel ing must be perform ed i n a suffi ciently ventilated room or in the ope n air . Never inhale fuel vapor , and ke ep fuel away from you. If you touch fuel repe atedly or fo r a long time, the skin becomes dry , which m ...

  • Makita EBH340R - page 14

    14 Observe all applic able accident preve ntion regulations! ST ARTING Move at lea st 3m away from the pl ace of refue lling. Place the br ush cutter on a clean p iece of gro und taking c are that the cut ting tool does not c ome in to co ntact with the grou nd or any o ther o bjects . A:Cold start 1) Set this machin e on a flat space. 2) Move the ...

  • Makita EBH340R - page 15

    15 Note: – If the starter handle is pulled re peatedly when the cho ke lever remains at "CLOSE" pos ition, the engine will not sta rt easily due to excessive f uel intake. – In c ase of ex cessive fu el inta ke, remov e the spa rk plug a nd pull the st arter han dle slowly t o remove excess fu el. Also , dry the electr ode sectio n of ...

  • Makita EBH340R - page 16

    16 SERVIC ING INS TRUCTIO NS C AU T IO N : Before doing any w ork on the brush cut ter , always stop the engine and pull the plug cap of f the spark plug (see "checking the spark plug"). Always wear pro tective gloves! T o ensur e a long servic e life and to avoid any d amage to the equipment, the following servicin g operati ons should b ...

  • Makita EBH340R - page 17

    17 5) Keep the engine level, and feed ne w oil up to the edge of the oil refi ll port. In refill, use a lubricant refill container. 6) After refill, se curely tigh ten the oil gauge. Insu fficient ti ghtening of the oil gauge will lead to oil leakage. POINTS ON OIL – Never discard replaced e ngine oil in garbage , earth or s ewage ditc h. Disposa ...

  • Makita EBH340R - page 18

    18 SUPPL Y OF GR EASE TO GEAR CAS E – Supply grease (S hell Alvania 2 or eq uivalen t) to the gear ca se through the greas e hole ev ery 30 hour s. (Genu ine MAKIT A gre ase may be pu rchased from your MAKIT A dealer .) CLEANING OF FUEL FILTER W ARNING : INFLAMMAB LES STRICTL Y PROHI BITED Interval of Cleanin g and Inspection: Monthly (every 50 o ...

  • Makita EBH340R - page 19

    19 ST ORAGE W AR NI NG : When drai ning the fue l, be sure t o stop the engine and confirm that the eng ine cools down. Just after stopping th e engine, it may st ill hot w ith possibilit y of burns , inflammabili ty and fi re. A TT EN T IO N: When th e machine i s kept out of operatio n for a lon g time, dr ain up all fuel from t he fuel t ank and ...

  • Makita EBH340R - page 20

    20 *1 Perform initial replacement after 20h operation. *2 For the 200 oper ating h our inspec tion, r equest Authorized Servic e A gent or a machin e shop. *3 After empty ing the fue l tank, contin ue to run th e engine an d drain fuel in the car buretor . Operating time Item Before operation After lubrication Daily (10h) 30h 50h 200h Shutdown /res ...

  • Makita EBH340R - page 21

    21 TROUBLE SHOOTING Before making a request for repairs, check a trouble f or yourself. If any abn ormality is found , control your ma chine according to the description of this manual. Never tamper or dismount any part contrary to the description. For repairs, contact Authorized Service Agent or local dealership. When t he engine does not start af ...

  • Makita EBH340R - page 22

    MEMO                                      ...

  • Makita EBH340R - page 23

    ...

  • Makita EBH340R - page 24

    61 195 22700 08.02 Makita Corporation 3-1 1-8, Sumiyoshi-cho, Anjo, Aichi 446-8502, Japan ...

メーカー Makita カテゴリー Brush Cutter

Makita EBH340Rのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- EBH340Rの取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita EBH340Rの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita EBH340Rの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita EBH340Rの取り付け説明書、サービスマニュアル、簡易説明書、またはMakita EBH340Rのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita EBH340Rの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita EBH340Rデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita EBH340Rを使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita EBH340Rユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita EBH340Rの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita EBH340Rの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita EBH340Rに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita EBH340Rデバイスの基本機能を使うにあたってのヒント。 Makita EBH340Rのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita EBH340Rに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita EBH340Rのメーカー/サービスへの連絡先に関する情報。

Makita EBH340Rについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita EBH340Rの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita EBH340Rで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)