日本語 dropdown-ico

Quatech DS-102の取扱説明書

35ページ 0.18 mb
ダウンロード

ページに移動 of 35

Summary
  • Quatech DS-102 - page 1

    DS-102 Dual Channel RS-232 Asynchronous Communications Adapter for ISA compatible machines User's Manual QUATECH, INC. TEL: (330) 434-3154 662 Wolf Ledges Parkway FAX: (330) 434-1409 Akron, Ohio 44311 BBS: (330) 434-2481 INTERFACE CARDS FOR IBM PC/AT AND PS/2 ...

  • Quatech DS-102 - page 2

    ...

  • Quatech DS-102 - page 3

    28 VIII. TROUBLESHOOTING 27 VII. SPECIFICATIONS 25 BAUD RATE SELECTION 24 FIFO polled mode operation (16550 UART only) 23 FIFO INTERRUPT MODE OPERATION (16550 UART only) 22 SCRATCHPAD REGISTER 22 MODEM STATUS REGISTER 21 LINE STATUS REGISTER 20 MODEM CONTROL REGISTER 19 LINE CONTROL REGISTER 18 FIFO CONTROL REGISTER (16550 only) 16 INTERRUPT IDENTI ...

  • Quatech DS-102 - page 4

    ...

  • Quatech DS-102 - page 5

    WARRANTY INFORMATION Quatech, Inc. warrants the DS-102 to be free of defects for one (1) year from the date of purchase. Quatech, Inc. will repair or replace any board that fails to perform under normal operating conditions and in accordance with the procedures outlined in this document during the warranty period. Any damage that results from impro ...

  • Quatech DS-102 - page 6

    © 1993, Quatech, Inc. NOTICE The information contained in this document cannot be reproduced in any form without the written consent of Quatech, Inc. Likewise, any software programs that might accompany this document can be used only in accordance with any license agreement(s) between the purchaser and Quatech, Inc. Quatech, Inc. reserves the righ ...

  • Quatech DS-102 - page 7

    I . GENERAL INFORMATION The Quatech, Inc. DS-102 provides two RS-232 asynchronous serial communication interfaces for IBM-compatible personal computer systems using the ISA (Industry Standard Architecture) expansion bus. The DS-102's two serial ports are implemented using 16450 Universal Asynchronous Receiver/Transmitters (UARTs). For higher p ...

  • Quatech DS-102 - page 8

    II . INSTALLATION If the default address and interrupt settings are sufficient, the DS-102 can be quickly installed and put to use. The factory defaults are listed in Figure 1 . YES 3 2F8 hex (COM2) Serial 2 YES 4 3F8 hex (COM1) Serial 1 ENABLED ? IRQ ADDRESS PORT Figure 1 --- Default address and IRQ settings for DS-102 The serial port outputs on t ...

  • Quatech DS-102 - page 9

    IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 Set IRQ levels here (Diagram not to scale) 16450/16550 16450/16550 SW1 Serial 1 SW2 Serial 2 J4 Set addresses here (SW1, SW2) (J5, J6) J7 J8 J1 Serial 1 Serial 2 CN1 CN2 J5 J6 Serial 1 Serial 2 J2 J3 QUATECH INC. DS-102 Figure 2 --- Diagram of DS-102 Quatech DS-102 User's Manual 3 ...

  • Quatech DS-102 - page 10

    III . ENABLING AND ADDRESSING PORTS Setting the address Each serial port on the DS-102 uses 8 consecutive I/O locations in the range of 0000 hex to 07FF hex. The base address of each port is set using a DIP switch pack on the DS-102. When setting the address selection switches, a switch in the "ON" position specifies that the correspondin ...

  • Quatech DS-102 - page 11

    Switch on bit = 0 Switch off bit = 1 Serial 1 uses SW1 Serial 2 uses SW2 Factory default setting for Serial 1 --- 03F8 hex (COM1) ON 1234567 8 8 2 1 F 4 8 8 2 1 3 0 SW1 Factory default setting for Serial 2 --- 02F8 hex (COM2) ON 123456 78 8 2 1 F 4 8 8 2 0 2 0 SW2 Example: 03E8 hex (typical for COM3) ON 1234567 8 8 2 0 E 4 8 8 2 1 3 0 Example: 02E8 ...

  • Quatech DS-102 - page 12

    The standard addresses for serial ports COM1 and COM2 are listed in Figure 5 . Recommended addresses for serial ports COM3 and COM4 are also listed. The switch settings for these addresses are shown in Figure 4 . 02E8 hex COM4 Recommendations only. No official standards exist for COM3 and COM4. 03E8 hex COM3 Factory default for Serial 2. 02F8 hex C ...

  • Quatech DS-102 - page 13

    (This page intentionally left blank.) Quatech DS-102 User's Manual 7 ...

  • Quatech DS-102 - page 14

    IV . SETTING INTERRUPT LEVELS ( IRQ S) The DS-102 interrupt circuitry allows each port to use any interrupt level in the range IRQ2 through IRQ7. The interrupt levels are selected using jumper packs J5 for Serial 1 and J6 for Serial 2. In Figure 7 , the factory default settings for Serial 1 and Serial 2 are shown. IRQ7 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 Seri ...

  • Quatech DS-102 - page 15

    Interrupt Sharing An interrupt sharing circuit allows a port on the DS-102 to share an interrupt with the other port on the board or with another Quatech adapter supporting sharable interrupts. When interrupt sharing is used, the software must query each port attached to a given IRQ level when an interrupt for that IRQ is received by the computer. ...

  • Quatech DS-102 - page 16

    V . EXTERNAL CONNECTIONS RS-232-C devices are classified by their function as either Data Terminal Equipment (DTE) or Data Communication Equipment (DCE). Generally, data terminal equipment is defined as the communication source and data communication equipment is defined as the device that provides a communication channel between two DTE-type devic ...

  • Quatech DS-102 - page 17

    To simplify connections to other devices, each port on the DS-102 is equipped with a jumper block that allows the port to be configured as either a DTE- or DCE-type device. This allows the DS-102 to communicate with either DTE- or DCE-type devices without using a null modem cable. J7 is used for Serial 1 and J8 is used for Serial 2. The DTE/DCE sel ...

  • Quatech DS-102 - page 18

    The DS-102 connects to peripheral equipment through male D-9 connectors. Adapters are available to convert these connectors into standard D-25 male connectors. The standard serial port connections are listed in Figure 13 . 22 9 22 9 Ring Indicator (RI) 4 7 5 8 Clear To Send (CTS) 5 8 4 7 Request To Send (RTS) 20 4 6 6 Data Set Ready (DSR) 7 5 7 5 S ...

  • Quatech DS-102 - page 19

    (This page intentionally left blank.) Quatech DS-102 User's Manual 13 ...

  • Quatech DS-102 - page 20

    VI . SERIAL PORT FUNCTIONAL DESCRIPTION This section contains information intended for advanced users planning to do custom programming with the DS-102. The information presented here is a technical description of the interface to the 16450 or 16550 UART. The 16450 UART is an improved functional equivalent of the 8250 UART, performing serial-to-par ...

  • Quatech DS-102 - page 21

    Accessing the Serial Port registers Figure 15 lists the address map for the 16450 and 16550 UARTs. Each register can be accessed by reading from or writing to the proper I/O address. This I/O address is determined by adding an offset to the base address set for the particular serial port. The base address is set using DIP switches on the DS-102 (se ...

  • Quatech DS-102 - page 22

    INTERRUPT ENABLE REGISTER This register is located at I/O address [base+1]. It enables the five types of UART interrupts. Interrupts can be totally disabled by setting all of the enable bits in this register to a logic 0. Setting any bit to a logic 1 enables that particular interrupt. ETBEI --- Received Data Available Interrupt: When set (logic 1), ...

  • Quatech DS-102 - page 23

    IP --- Interrupt pending: When logic 0, indicates that an interrupt is pending and the contents of the interrupt identification register may be used to determine the interrupt source. See Figure 18 . 0 IID0 --- 1 IID1 --- 2 Interrupt Identification: Indicates highest priority interrupt pending if any. See Figure 18 . NOTE: IID2 is always a logic 0 ...

  • Quatech DS-102 - page 24

    FIFO CONTROL REGISTER (16550 only) This register, which applies only to the 16550 UART, is a write-only register located at I/O address [base+2]. It is used to enable the FIFO mode, clear the FIFOs, set the threshold level for the receive FIFO to generate interrupts, and to set the mode under which the device uses DMA. Note that DMA mode is NOT sup ...

  • Quatech DS-102 - page 25

    LINE CONTROL REGISTER This register is located at I/O address [base+3]. It is used for specifying the format of the asynchronous serial data to be processed by the UART, and to set the Divisor Latch Access Bit (DLAB) allowing access to the baud rate divisor latches. WLS0 --- 0 Word length select: Determines the number of bits per transmitted word. ...

  • Quatech DS-102 - page 26

    MODEM CONTROL REGISTER This register is located at I/O address [base+4], and is used to control the interface with the modem or device used in place of a modem. This register allows the states of the "modem control signals" to be changed. These are DTR (Data Terminal Ready) and RTS (Request To Send). It is also possible to place the UART ...

  • Quatech DS-102 - page 27

    LINE STATUS REGISTER This register is located at I/O address [base+5]. It is used to provide various types of status information concerning the data transfer. As Figure 22 shows, the Line Status Register indicates several types of errors, an empty transmit buffer, a ready receive buffer, or a break on the receive line. DR --- Data ready: Indicates ...

  • Quatech DS-102 - page 28

    MODEM STATUS REGISTER This register is located at I/O address [base+6]. It reports on the status of signals coming from the modem or equipment used in place of a modem. It allows the current states of "modem control signals" to be sensed. These signals include the DCD (Data Carrier Detect), RI (Ring Indicator), DSR (Data Set Ready), and C ...

  • Quatech DS-102 - page 29

    FIFO INTERRUPT MODE OPERATION (16550 UART only) When the receiver FIFO and receiver interrupts are enabled: 1 . The receive data interrupt is issued when the receive FIFO reaches the trigger level. The interrupt is cleared as soon as the receive FIFO falls below the trigger level. 2 . The Interrupt Identification Register's receive data availa ...

  • Quatech DS-102 - page 30

    FIFO polled mode operation (16550 UART only) The receiver and transmitter are operated independently, which would allow either or both to be used in a polled mode rather than using interrupts to determine when the UART needs to be serviced. To use the UART in a polled mode, the software is responsible for continuously checking for the conditions th ...

  • Quatech DS-102 - page 31

    BAUD RATE SELECTION The 16450 or 16550 UART determines the baud rate of the serial output using a combination of the clock input frequency and the value written to the divisor latches. Standard personal computer serial interfaces use an input clock of 1.8432 MHz. To increase versatility, the DS-102 uses an 18.432 MHz crystal and a frequency divider ...

  • Quatech DS-102 - page 32

    2.86 2 56000 - 3 38400 - 6 19200 - 12 9600 - 16 7200 - 24 4800 - 32 3600 - 48 2400 0.69 58 2000 - 64 1800 - 96 1200 - 192 600 - 384 300 - 768 150 0.026 1047 110 - 1536 75 - 2304 50 ERROR BETWEEN DESIRED AND ACTUAL VALUES (%) DIVISOR LATCH VALUE DESIRED BAUD RATE Figure 25 --- Divisor Latch settings for common baud rates using 1.8432 MHz input clock ...

  • Quatech DS-102 - page 33

    VII . SPECIFICATIONS Bus interface: Industry Standard Architecture (ISA) 8-bit bus Serial ports Controller: 16450 (16550 optional) Interface: Two male D-9 connectors Two male D-25 connectors optional using adapter cables Transmit drivers: MC1488 or compatible High level output voltage: +9V min, +10.5V max Low level output voltage: -9V min, -10.5V m ...

  • Quatech DS-102 - page 34

    VIII . TROUBLESHOOTING Listed here are some common problems and frequent causes of those problems. Suggestions for corrective action are given. If the information here does not provide a solution, contact Quatech Customer Service for technical support. Any unauthorized repairs or modifications will void the DS-102's warranty. Computer will not ...

  • Quatech DS-102 - page 35

    DS-102 Dual Channel RS-232 Asynchronous Communications Adapter User's Manual Revision 3.00 August 13, 1993 ...

メーカー Quatech カテゴリー Network Card

Quatech DS-102のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DS-102の取扱説明書
- Quatechの製品カード
- パンフレット
- またはQuatech DS-102の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Quatech DS-102の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Quatech DS-102の取り付け説明書、サービスマニュアル、簡易説明書、またはQuatech DS-102のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Quatech DS-102の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Quatech DS-102デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがQuatech DS-102を使用するのを助ける技術的文書のことです。説明書は通常、全てのQuatech DS-102ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Quatechの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Quatech DS-102の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははQuatech DS-102の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Quatech DS-102に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Quatech DS-102デバイスの基本機能を使うにあたってのヒント。 Quatech DS-102のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Quatech DS-102に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるQuatech DS-102のメーカー/サービスへの連絡先に関する情報。

Quatech DS-102についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもQuatech DS-102の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがQuatech DS-102で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)