Epson LX-300+の取扱説明書

16ページ 0.94 mb
ダウンロード

ページに移動 of 16

Summary
  • Epson LX-300+ - page 1

    EPSON LX-300+ 5/00 EPSON LX-300+ - 1 User Replaceable Parts Options Single-bin Cut-sheet Feeder (C806371) Feeds up to 50 sheets of ordinary single-sheet paper. Additional Tractor Unit (C800301) Used in combination with the other tractor, improves continuous paper handling and reduces the chance of paper jams. This is especially useful for printing ...

  • Epson LX-300+ - page 2

    EPSON LX-300+ 2 - EPSON LX-300+ 5/00 Electrical Environmental Line spacing 1/6 inch or programmable in 1/216-inch increments Printable columns 80 columns (at 10 cpi) Resolution (maximum) 240 × 144 dpi (NLQ) Interfaces 1 standard bidirectional, 8-bit parallel interface with IEEE-1284 nibble mode support, and 1 EIA-232D serial interface Paper feed m ...

  • Epson LX-300+ - page 3

    EPSON LX-300+ 5/00 EPSON LX-300+ - 3 Paper Use recycled paper, envelopes, and single-sheet multipart forms only under normal temperature and humidity conditions, as follows: Temperature: 59 to 77 °F (15 to 25 °C) Humidity: 30 to 60% RH Do not load paper that has been folded or is damaged, wrinkled, or curled. Ordinary single sheets: paper guide a ...

  • Epson LX-300+ - page 4

    EPSON LX-300+ 4 - EPSON LX-300+ 5/00 Paper Alignment Printing starts at “0” on the scale. The unprintable area is to the left of the “0”. Printable Area Single sheets and envelopes A The minimum top margin is 0.17 inch (4.2 mm). B The minimum left and right margins are 0.12 inch (3 mm). The maximum paper width is 10.1 inches (257 mm). The m ...

  • Epson LX-300+ - page 5

    EPSON LX-300+ 5/00 EPSON LX-300+ - 5 Safety Approvals 120 V Safety standards UL 1950 CSA C22.2 No. 950 EMI FCC part 15 subpart B class B CSA C108.8 class B 230 V Safety standards EN 60950 EMI EN 55022 (CISPR pub. 22) class B AS/NZS 3548 class B Acoustic noise Approx. 49 dB (A) (ISO 7779 pattern) CE Marking 230 V Low Voltage Directive 73/23/EEC EN 6 ...

  • Epson LX-300+ - page 6

    EPSON LX-300+ 6 - EPSON LX-300+ 5/00 Selecting Fonts After entering the Micro Adjust mode by holding down the Pause button for three seconds, you can change font settings with the Tear Off button. The two Tear Off lights come on ( n ) and go off ( o ) to show the current selection. Press the button repeatedly to cycle through all of the available s ...

  • Epson LX-300+ - page 7

    EPSON LX-300+ 5/00 EPSON LX-300+ - 7 Paper Positions Top-of-Form Position The top-of-form position is where the printer starts printing on single sheets or continuous paper. Tear-off Position Continuous paper is in the tear-off position when the perforation is aligned with the tear-off edge. You can easily tear off your printed document at this pos ...

  • Epson LX-300+ - page 8

    EPSON LX-300+ 8 - EPSON LX-300+ 5/00 Printing with the Pull Tractor To load continuous paper using the pull tractor, you must move the tractor to the pull tractor position, as described in steps 1 through 4 below. If your tractor is already installed in this position, make sure the printer is off and skip to step 7. Use the knob on the left side of ...

  • Epson LX-300+ - page 9

    EPSON LX-300+ 5/00 EPSON LX-300+ - 9 7. Slide the left sprocket unit so that its sprockets match the position of the holes in the paper and lock the unit in place. Then slide the right sprocket unit to match the width of your paper, but do not lock it. Move the paper support midway between the two sprocket units. 8. Open the sprocket covers, fit th ...

  • Epson LX-300+ - page 10

    EPSON LX-300+ 10 - EPSON LX-300+ 5/00 To adjust the top-of-form position for continuous paper loaded on the pull tractor, see the following example: First mark a point 0.1 inch (2.5 mm) above the paper’s perforation; then position the paper so that the mark is even with the top edge of the plastic ribbon cover. This gives you a 0.33-inch (8.5-mm) ...

  • Epson LX-300+ - page 11

    EPSON LX-300+ 5/00 EPSON LX-300+ - 11 5. After you set the tear-off position, press the Pause button to turn off the Micro Adjust mode. 6. Tear off the printed page(s). When you resume printing, the printer automatically feeds the paper back to the top-of-form position. Printing on Single Sheets You can load single-sheet paper one sheet at a time u ...

  • Epson LX-300+ - page 12

    EPSON LX-300+ 12 - EPSON LX-300+ 5/00 Adjusting the Paper Thickness Lever Before printing on special paper, you need to change the paper thickness setting. The paper thickness lever is under the cover on the left side of the printer. The numbers next to the lever indicate the thickness setting. Use the table below to select the appropriate paper th ...

  • Epson LX-300+ - page 13

    EPSON LX-300+ 5/00 EPSON LX-300+ - 13 Default Settings While you can often set the default settings through your application software or printer driver, you may need to change a default setting from the printer’s control panel using the default setting mode. The table below lists the default settings (in bold) and options you can select in this m ...

  • Epson LX-300+ - page 14

    EPSON LX-300+ 14 - EPSON LX-300+ 5/00 Bidirectional Alignment If you notice that the vertical lines in your printout are not properly aligned, you can use the printer’s bidirectional adjustment mode to correct this problem. To complete the steps below, you need 5 letter or A-4 size single sheets or 5 pages of continuous paper. If you use single s ...

  • Epson LX-300+ - page 15

    EPSON LX-300+ 5/00 EPSON LX-300+ - 15 Cleaning the Printer To keep your printer operating at its best, you should clean it thoroughly several times a year. Follow these steps: 1. Remove any paper loaded in the printer and turn it off. 2. Unplug the power cord from the electrical outlet; then disconnect the interface cable from the printer. 3. Remov ...

  • Epson LX-300+ - page 16

    EPSON LX-300+ 16 - EPSON LX-300+ 5/00 ...

メーカー Epson カテゴリー Printer

Epson LX-300+のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- LX-300+の取扱説明書
- Epsonの製品カード
- パンフレット
- またはEpson LX-300+の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Epson LX-300+の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Epson LX-300+の取り付け説明書、サービスマニュアル、簡易説明書、またはEpson LX-300+のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Epson LX-300+の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Epson LX-300+デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがEpson LX-300+を使用するのを助ける技術的文書のことです。説明書は通常、全てのEpson LX-300+ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Epsonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Epson LX-300+の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははEpson LX-300+の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Epson LX-300+に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Epson LX-300+デバイスの基本機能を使うにあたってのヒント。 Epson LX-300+のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Epson LX-300+に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるEpson LX-300+のメーカー/サービスへの連絡先に関する情報。

Epson LX-300+についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもEpson LX-300+の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがEpson LX-300+で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)