-
Bostitch N88WW/N88RH - page 1
BEFORE OPERA TING THIS T OOL, ALL OPERA T ORS SHOULD STUD Y THIS MANU AL T O UNDER- ST AND AND FOLLO W THE SAFETY W ARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUC- TIONS WITH THE T OOL FOR FUTURE REFERENCE. IF Y OU HA VE ANY QUESTIONS, CONT A CT Y OUR BOSTITCH REPRESENT A TIVE OR DISTRIBUTOR. ANTES DE OPERAR EST A HERRAMIENT A, T ODOS LOS OPERADORES ...
-
Bostitch N88WW/N88RH - page 2
INTRODUCTION The Bostitch N88 is a precision-built tool, designed f or high speed, high volume nailing. These tools will deliver efficient, dependab le ser vice when used correctly and with care. As with any fine pow er tool, for best perf ormance the manu f acturer’ s instructions must be follo wed. Please study this manual bef ore operating the ...
-
Bostitch N88WW/N88RH - page 3
-3- SAFETY INSTRUCTIONS EYE PR O TECTION which conforms to ANSI specifications and pro vides protection against flying particles both fr om the FRONT and SIDE should AL W A YS be worn by the operator and others in the w ork area when loading, operating or servicing this tool. Eye protection is required to guar d against flying fastener s and debris ...
-
Bostitch N88WW/N88RH - page 4
-4- N88 TOOL SPECIFICA TIONS All screws and nuts are metric. F ASTENER SPECIFICA TIONS: N88WW This tool uses a 28° wire collated stick nail in lengths of 2” to 3-1/2” (50 - 90mm) and shank diameters of .113” to .131” (2.8 - 3.3mm) N88RH This tool uses a 21° plastic collated full round head stick nail in lengths of 2” to 3-1/2” (50 - 9 ...
-
Bostitch N88WW/N88RH - page 5
AIR SUPPL Y AND CONNECTIONS Do not use oxygen, combustible gases, or bottled gases as a power source f or this tool as tool may explode, possibly causing injury . FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source. HOSES: Air hoses should hav e a ...
-
Bostitch N88WW/N88RH - page 6
EYE PR O TECTION which conforms to ANSI specifications and pro vides protec- tion against flying particles both fr om the FRONT and SIDE should AL W A YS be worn b y the operator and others in the work area when loading, operating or ser- vicing this tool. Eye protection is required to guar d against flying fastener s and debris, which could cause ...
-
Bostitch N88WW/N88RH - page 7
-7- The F astener Depth Control Adjustment feature provides control of the nail driv e depth from flush with or just above the work surface to shallow or deep countersink. T O ADJUST THE F ASTENER DEPTH CONTROL: DISCONNECT TOOL FR OM AIR SUPPL Y BEFORE A TTEMPTING ANY P ARTS DISASSEMBL Y AND BEFORE CHANGING THE WORK CONT ACTING ELEMENT ADJUSTMENT . ...
-
Bostitch N88WW/N88RH - page 8
TOOL OPERA TION OPERA TION EYE PR O TECTION which conforms to ANSI specifications and provides pr o- tection against flying particles both fr om the FRONT and SIDE should AL W A YS be worn by the operator and other s in the work area when loading, operating or servicing this tool. E ye protection is required to guard a gainst flying fasteners and d ...
-
Bostitch N88WW/N88RH - page 9
TOOL OPERA TION CHECK: CA UTION: Remove all fasteners fr om tool before perf orming tool operation check. 1. CONT A CT TRIP OPERA TION: A. With finger off the trigger, press the contact trip against the work surf ace. THE T OOL MUST NO T CYCLE. B. Hold the tool off the work surface , and pull the trigger. THE T OOL MUST NO T CYCLE. C. With the tool ...
-
Bostitch N88WW/N88RH - page 10
-10- MAINT AINING THE PNEUMA TIC TOOL When working on air tools, note the warnings in this manual and use extra care evaluating pr oblem tools. CA UTION: Pusher spring (constant for ce spring). Caution must be used when working with the spring assembly . The spring is wrapped ar ound, but not attached to, a roller . If the spring is extended bey on ...
-
Bostitch N88WW/N88RH - page 11
T rigger valve housing leaks air O-ring cut or cracked . . . . . . . . . . . . . .Replace O-r ing T rigger valve stem leaks air O-ring/seals cut or cracked . . . . . . . . . .Replace trigger valve assemb ly Frame/nose leaks air Loose nose screws . . . . . . . . . . . . . . .Tighten and recheck O-ring or Gasket is cut or crack ed . . . .Replace O-ri ...
-
Bostitch N88WW/N88RH - page 12
N88 DRIVER MAINTENANCE INSTRUCTIONS Worn driver causing poor quality or loss of pow er : - Wear on the driving tip will affect the nail driv e, giving symptoms of bent and incompletely driven nails, and damaged nail heads. - The driver length may be adjusted to allo w the driving tip to be redressed to compensate for wear . Heat and precise measure ...
Bostitch N88WW/N88RHについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもBostitch N88WW/N88RHの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBostitch N88WW/N88RHで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。