Makita 3702Bの取扱説明書

23ページ 1 mb
ダウンロード

ページに移動 of 23

Summary
  • Makita 3702B - page 1

    Tkimmer Collet chuck capacity 14 _~____~__ 1/4” MODEL 3702B Net weight Overall lenqth No load speed (RPMI 28 000 296 mm 11 1 5 8 1 1 6 kg 13 5 lbsl - INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS ...

  • Makita 3702B - page 2

    IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit ...

  • Makita 3702B - page 3

    14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext ...

  • Makita 3702B - page 4

    ADDITIONAL SAFETY RULES 1. Wear hearing protection during extended periods of operation. 2. Handle the bits very carefully. 3. Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediately. 4. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 5. Hold the tool firml ...

  • Makita 3702B - page 5

    Installing or removing trimmer bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. Insert the bit all the way into the collet cone and tighten the collet nut securely with the two wrenches. To remove the bit, follow the installation procedure in reverse. CAUTION : 0 Do not tighten the coll ...

  • Makita 3702B - page 6

    Adjusting angle of tool base Loosen the wing bolts and adjust the angle of the tool base (5' per graduation) to obtain the desired cutting angle. - Gradual Wing nut __ Wing bolt ~___ Base It of ring Adjusting amount of chamfering To adjust the amount of chamfering, loosen the wing nuts and adjust the trimmer shoe. CAUTION : With the tool unplu ...

  • Makita 3702B - page 7

    When doing edge cutting, the workpiece surface should be on the left side of the bit in the feed direction. (See the figure below) Feed direction (View from the top of the tool) Correct bit feed Bit revolving direction Feed direction 2w direction NOTE : Moving the tool forward too fast may cause a poor quality of cut, or damage to the bit or motor. ...

  • Makita 3702B - page 8

    Straight guide The straight guide is effectively used for straight cuts when chamfering or grooving. Attach the guide plate to the straight guide with the bolt, the wave washer, the flat washer and the wing nut. Loosen the wing bolts and secure the tool base horizontally. Attach the straight guide with the clamp screw (A). Loosen the wing nut on th ...

  • Makita 3702B - page 9

    Circular work 0Circular work may be accomplished if you assemble the straight guide and guide plate 0 Min. and max. radius of circles to be cut (distance between the center of circle and the as shown in the figure below. center of bit) are as follows : Min. : 70 mm (2-3/4") Max. : 221 mm (8-11/16") (Note) Circles between 172 mm (6-3/4&quo ...

  • Makita 3702B - page 10

    Trimmer guide Trimming, curved cuts for furniture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut. Loosen the wing bolts and secure the tool base horizontally. Install the trimmer guide on the tool base with the clamp screw (A). Loosen the clamp screw (6) and adjust the distance betwee ...

  • Makita 3702B - page 11

    Templet guide The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns. Remove the tool base from the tool. Loosen the wing bolts and secure the tool base horizontally. Loosen the two screws on the tool base. Place the templet guide on the tool base. There are four convex portions on the te ...

  • Makita 3702B - page 12

    Secure the templet to the workpiece. Place I the tool on the templet and move the tool with the templet guide sliding along the side of the templet. Straight bit I Templet guide Base r I. I Distance (X) Workpiece 10 mm (25/64") L NOTE : The workpiece will be cut a slightly different size from the templet. Allow for the dis- tance (X) between ...

  • Makita 3702B - page 13

    MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes I Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be ...

  • Makita 3702B - page 14

    ACCESS0 R I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Straight guide assembly Part No. 122391-0 ...

  • Makita 3702B - page 15

    Bits STRAIGHT -Single Flute HIGH SPEED STEEL PART NO. A E C D E 733232-6A 118 5/16 1-1 18 114 1-518 CARBIDE TIPPED PART NO @ STRAIGHT - 2 Flute A E C D E 733003-2A 3/16 7116 1 318 1 I4 2 733003-EA 5/16 1 1-1 18 114 2-3/16 733003-4A 114 314 1-3116 114 2-118 HIGH SPEED STEEL (STRAIGHT - 2 Flute1 PART NO A E C D E 733233-4A 5/16 7/E 1-3/16 114 2-1 18 ...

  • Makita 3702B - page 16

    ROUND NOSE -I& CARBIDE TIPPED PART NO. A a C D E 733008-4A 318 9/16 1-114 1 I4 2 733008-2A 114 15132 1-1 I4 1 /4 1-718 CORE BOX 4DC &, A/- -J f I HIGH SPEED STEEL PART NO. A E C D E 73323a-2~ 114 1 /4 1-3/16 114 1-1 12 VEE GROOVING IDk CARBIDE TIPPED PART NO. A B C D E 8 733009-2A 318 112 1-3/16 1/4 2 90" 14" DOVE TAIL -bc CARBIDE ...

  • Makita 3702B - page 17

    PANEL PILOT HIGH SPEED STEEL PART NO. A B C D E 733236-0A 114 314 1 114 2-7116 CORNER ROUNDING CARBIDE TIPPED - Ball Bearing Pilot 733120 OA 7/8 112 318 1 114 114 115116 3/16 7331 20 2A 112 1 114 114 114 REPLACEMENT BEARING - NO 733132 4A HIGH SPEED STEEL -Solid Pilot PARTNO A, A2 B C D E R 733240 2A 11/16 3/16 112 1 114 1 314 114 733240 6A 15/16 3 ...

  • Makita 3702B - page 18

    ROMAN OGEE CARBIDE TIPPED - Ball Bearing Pilot I PARTNO. AI A? B C 0 E RI 5132 I 733123-2A 1 3/8 15/32 1-1/4 1/4 REPLACEMENT BEARING - NO, 733132-2A FLUSH TRIMMER -Self Piloting SOLID CARBIDE PART NO. A B C D E 7331 28-OA 1 /4 1 I4 1-1/16 114 1-9/16 7" BEVEL TRIMMER - Self-Piloting SOLID CARBIDE PART NO. A B C D E 733128-2A 3/16 1 /4 1-1/16 1 ...

  • Makita 3702B - page 19

    COMB1 NATION F LUSH/2Z0 BEVEL TRIMMER SDC CARBIDE TIPPED 733128-6A 7/16 112 3/16 1-1/4 1/4 1-314 3 FLUTE FLUSH TRIMMER ASSEMBLY -Self Piloting -I uc SOLID CARBIDE CUTTER I PARTNO. A B C D E 733129-2A 518 3/8 1-114 114 2-318 REPLACEMENT BEARING ~ NO. 733132-6A 3 FLUTE 22" BEVEL TRIMMER ASSEMBLY -self Piloting -I[+ I REPLACEMENT BEARING ~ NO 733 ...

  • Makita 3702B - page 20

    3 FLUTE 22" BEVEL REPLACEMENT CUTTER LA4 SOLID CARBIDE I PARTNO. A B D I 733129-8A 718 3/8 1 /4 FOR BEVEL TRIMMER ASSEMBLY NO, 733129-4A 114" REPLACEMENT ARBOR PART NO A B C D E 733131,2A 5/8 3/8 1-114 1 /4 2 318 FOR FLUSH TRIMMER ASSEMBLY NO 733129-2A AND NO 733129-4A BALL BEARING PILOT Dl Dz PART NO. 7331 32-2A 3/8 O.D. 1/8 I.D. 733132- ...

  • Makita 3702B - page 21

    Apr 06 ‘89 US 114” TRIMMER Model 3702B Note The switch, noise suppressor and other part conflguratlons may differ from country to country ...

  • Makita 3702B - page 22

    MODEL 37028 ;:, DESCRIPTION Apr 04 '89 US 'k,'o" ,"., DESCRIPTION MACHINE ~ 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 1 1 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 2 2 1 2 1 - Hex NulM12 Motor Rear Housing Carbon Brush Brush Holder Cap Switch FIELD ASSEMBLY Ball Bearing 627LB Insulation Washer Rubber Pin 4 Hex Bo11 M4x7 ...

  • Makita 3702B - page 23

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool IS thoroughly inspected and tested before leaving the factory. It IS warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh ...

メーカー Makita カテゴリー Trimmer

Makita 3702Bのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 3702Bの取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita 3702Bの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita 3702Bの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita 3702Bの取り付け説明書、サービスマニュアル、簡易説明書、またはMakita 3702Bのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita 3702Bの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita 3702Bデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita 3702Bを使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita 3702Bユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita 3702Bの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita 3702Bの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita 3702Bに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita 3702Bデバイスの基本機能を使うにあたってのヒント。 Makita 3702Bのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita 3702Bに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita 3702Bのメーカー/サービスへの連絡先に関する情報。

Makita 3702Bについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita 3702Bの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita 3702Bで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)