John Deere ET-3410-Jの取扱説明書

24ページ 0.52 mb
ダウンロード

ページに移動 of 24

Summary
  • John Deere ET-3410-J - page 1

    Metal Cutting Saw Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE METAL SAW AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT. ET -3410-J 7-INCH MET AL CUTTING SA W ...

  • John Deere ET-3410-J - page 2

    2 Metal Cutting Saw Operator's Manual Congratulations on the purchase of your new John Deere 7-inch Metal Cutting Saw! You can be assured your metal cutting saw was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. This operator's manual was ...

  • John Deere ET-3410-J - page 3

    Metal Cutting Saw Operator's Manual 3 T able of Content SAFETY ......................................................................................................................... .................. 4-13 GENERAL SAFETY RULES ............................................................................................... 4-8 SPECIFIC SAFETY ...

  • John Deere ET-3410-J - page 4

    4 Metal Cutting Saw Operator's Manual RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your tool or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A "DANGER, WARNING or CAUTION" safety warning ...

  • John Deere ET-3410-J - page 5

    Metal Cutting Saw Operator's Manual 5 GENERAL SAFETY RULES: WORK AREA Keep work area clean and well lit. Cluttered areas and benches invite injuries. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. Keep bystanders, c ...

  • John Deere ET-3410-J - page 6

    6 Metal Cutting Saw Operator's Manual MINIMUM GAUGE FOR EXTENSION CORDS VOLTS TOTAL LENGTH OF CORD IN FEET 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 AMPERAGE 0-6 18 16 16 14 6-10 18 16 14 12 10-12 16 16 14 12 12-16 14 12 NOT RECOMMENDED RECOMMENDED WIRE GAUGE *JOHN DEERE RECOMMENDS USING A MINIMUM 12 GAUGE EXTENSION CORD ...

  • John Deere ET-3410-J - page 7

    Metal Cutting Saw Operator's Manual 7 GENERAL SAFETY RULES: PERSONAL SAFETY Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. Dress ...

  • John Deere ET-3410-J - page 8

    8 Metal Cutting Saw Operator's Manual CAUTION GENERAL SAFETY RULES: SERVICE Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of ...

  • John Deere ET-3410-J - page 9

    Metal Cutting Saw Operator's Manual 9 CAUTION SPECIFIC SAFETY RULES: DANGER: KEEP HANDS AND BODY AWAY FROM AND TO THE SIDE OF THE BLADE. CONTACT WITH BLADE WILL RESULT IN SERIOUS INJURY. DANGER: KEEP HANDS AWAY FROM CUTTING AREA AND BLADE. KEEP YOUR SECOND HAND ON AUXILIARY HANDLE, OR MOTOR HOUSING. IF BOTH HANDS ARE HOLDING THE SAW, THEY CANN ...

  • John Deere ET-3410-J - page 10

    10 Metal Cutting Saw Operator's Manual CAUTION SPECIFIC SAFETY RULES: CAUSES AND OPERATOR PREVENTION OF KICKBACK: Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator. When the blade is pinched or bound tightly by the kerf closing down, th ...

  • John Deere ET-3410-J - page 11

    Metal Cutting Saw Operator's Manual 11 CAUTION SPECIFIC SAFETY RULES: SUPPORT LARGE PANELS Large panels must be supported as shown in Fig. A to minimize the risk of blade pinching and kickback. When cutting operation requires the resting of saw on the work piece, the saw shall be rested on the larger portion and the smaller piece cut off. USE ...

  • John Deere ET-3410-J - page 12

    12 Metal Cutting Saw Operator's Manual SPECIFIC SAFETY RULES: CONFIRM THAT NO ITEMS SUCH AS AN ELECTRIC CABLE OR CONDUIT ARE BURIED INSIDE Be sure the saw will not cut through wire, cable or conduit that are behind or under the area you are cutting. In such cases, metal parts could become electrically live and present a serious shock hazard. K ...

  • John Deere ET-3410-J - page 13

    Metal Cutting Saw Operator's Manual 13 SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS AND OWNERS OF THIS TOOL! SPECIFIC SAFETY RULES: 1. If you require an additional manual, please contact John Deere Customer Service: Mi-T-M ® Corporation, 8650 Enterprise Drive, Peosta, IA 52068 1-877-JD-KLEEN / (1-877-535-5336) Fax 563-556-12 ...

  • John Deere ET-3410-J - page 14

    14 Metal Cutting Saw Operator's Manual Functional Description MODEL: ET-3410-J 7-INCH METAL CUTTING SAW NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all ...

  • John Deere ET-3410-J - page 15

    Metal Cutting Saw Operator's Manual 15 Operation APPLICATIONS: Cutting various types of metals. ASSEMBLY: WARNING: ALWAYS DISCONNECT THE SAW FROM POWER SOURCE BEFORE MAKING ADJUSTMENTS. Install authorized saw blade as detailed in the "Change Saw Blade" on page 19. PRE-OPERATION: PREPARE MATERIAL BEFORE CUTTING: 1. The type of materia ...

  • John Deere ET-3410-J - page 16

    16 Metal Cutting Saw Operator's Manual Operation PRE-OPERATION: SETTING BLADE DEPTH WARNING: DISCONNECT POWER CORD BEFORE ADJUSTING BLADE DEPTH. 1. Disconnect power cord. 2. Loosen T-knob (A). (Fig. 3) 3. Raise or lower the saw base to the desired position. For proper depth setting, the blade should extend no more than 6 mm (1/4 in) below the ...

  • John Deere ET-3410-J - page 17

    Metal Cutting Saw Operator's Manual 17 Operation OPERATION: CUTTING MATERIAL 1. The surface you are working on should be clean and level, free from rust, scale, dirt and chips. 2. Adjust the base plate to the desired bevel angle by loosening and then retightening the T-knob. Be certain depth and angle adjusting knobs are tight. 3. Adjust base ...

  • John Deere ET-3410-J - page 18

    18 Metal Cutting Saw Operator's Manual Operation OPERATION (CONTINUED): EMPTY CHIP COLLECTOR WARNING: ALWAYS DISCONNECT THE SAW FROM THE POWER SOURCE BEFORE CHANGING BLADES, CLEARING CHIPS OR MAKING ADJUSTMENTS. CAUTION: ALLOW SAW TO COOL BEFORE EMPTYING CHIP COLLECTOR. CHIPS MAY BECOME HOT WHILE CUTTING. 1. Disconnect power cord from receptac ...

  • John Deere ET-3410-J - page 19

    Metal Cutting Saw Operator's Manual 19 Maintenance and Inspection MAINTENANCE AND INSPECTION: CHANGING SAW BLADES WARNING: ALWAYS DISCONNECT THE SAW FROM THE POWER SOURCE BEFORE CHANGING BLADES, CLEARING CHIPS OR MAKING ADJUSTMENTS. 1. Disconnect power cord from receptacle. 2. Place saw on level, secure surface. 3. Remove two (2) saw blade hou ...

  • John Deere ET-3410-J - page 20

    20 Metal Cutting Saw Operator's Manual Maintenance and Inspection MAINTENANCE AND INSPECTION: WARNING: TO AVOID AN ACCIDENT OR PERSONAL INJURY, ALWAYS CONFIRM THAT THE TRIGGER SWITCH IS TURNED OFF AND THE POWER PLUG HAS BEEN DISCONNECTED FROM THE RECEPTACLE BEFORE PERFORMING ANY MAINTENANCE OR INSPECTION OF THIS TOOL. 1. Inspecting the saw bla ...

  • John Deere ET-3410-J - page 21

    Metal Cutting Saw Operator's Manual 21 Accessories ACCESSORIES: WARNING: ACCESSORIES FOR THIS POWER TOOL ARE MENTIONED IN THIS INSTRUCTION MANUAL. THE USE OF ANY OTHER ATTACHMENT OR ACCESSORY CAN BE DANGEROUS AND COULD CAUSE INJURY OR MECHANICAL DAMAGE. Part # Application AT-4423-J Mild steel cutting (solid plate or bar, 5/16" / 8 mm maxi ...

  • John Deere ET-3410-J - page 22

    22 Metal Cutting Saw Operator's Manual T roubleshooting TROUBLESHOOTING: Low Blade Life/Teeth Chipping: - Wrong blade for the type of material. a. AT-4423-J for mild steel up to 5/16" solid. b. AT-4424-J for aluminum up to 3/8" solid. c. AT-4425-J for stainless steel up to 1/4" solid. - Aggressive contact with blade into materia ...

  • John Deere ET-3410-J - page 23

    Metal Cutting Saw Operator's Manual 23 Notes ...

  • John Deere ET-3410-J - page 24

    24 Metal Cutting Saw Operator's Manual Manufactured for Deere & Company, Moline, Illinois 61265 7-inch Metal Cutting Saw Operator's Manual #37-0746-021403 ©Copyright 2003, John Deere ...

メーカー John Deere カテゴリー Saw

John Deere ET-3410-Jのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ET-3410-Jの取扱説明書
- John Deereの製品カード
- パンフレット
- またはJohn Deere ET-3410-Jの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、John Deere ET-3410-Jの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、John Deere ET-3410-Jの取り付け説明書、サービスマニュアル、簡易説明書、またはJohn Deere ET-3410-Jのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、John Deere ET-3410-Jの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

John Deere ET-3410-Jデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJohn Deere ET-3410-Jを使用するのを助ける技術的文書のことです。説明書は通常、全てのJohn Deere ET-3410-Jユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

John Deereの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. John Deere ET-3410-Jの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJohn Deere ET-3410-Jの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。John Deere ET-3410-Jに関してこのドキュメントで見つけることができる全てのヒントの目次
3. John Deere ET-3410-Jデバイスの基本機能を使うにあたってのヒント。 John Deere ET-3410-Jのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。John Deere ET-3410-Jに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJohn Deere ET-3410-Jのメーカー/サービスへの連絡先に関する情報。

John Deere ET-3410-Jについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJohn Deere ET-3410-Jの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJohn Deere ET-3410-Jで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)