Pressure Systems 9016の取扱説明書

13ページ 1.17 mb
ダウンロード

ページに移動 of 13

Summary
  • Pressure Systems 9016 - page 1

    Model 9016 Upgrade Instructions February 2004 NetScanner™ System www. PressureSystems .com ...

  • Pressure Systems 9016 - page 2

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 1 Packing List When you purchase your 9016 Upgrade Kit, the following parts will be included: G 1 - 9016 Upgrade Installation Instructions G 1 - Upgrade Tag G 1 - PC327 analog board G 1 - Assembled PC322-PC323 processor unit G 1 - Cable tie 5.5 inch ...

  • Pressure Systems 9016 - page 3

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 2 Figure 1 Exploded View of 9016 Scanner Figure 2 9016 Top Plate 9016 Upgrade Instructions The following instructions must be followed to successfully upgrade the hardware and firmware in your current 9016 Intelligent Pressure Scanner to 9116 scanner capabilities. Figure 1 is ...

  • Pressure Systems 9016 - page 4

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 3 When performing any type of maintenance of NetScanner ™ System components, the following guidelines and precautions should always be followed: ! Verify that the work area and technicians are properly grounded to prevent damage to electronic components due to electrostatic ...

  • Pressure Systems 9016 - page 5

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 4 Figure 3 9016 Top Plate Remove 12 perimeter Phillips- head screws. REMOVE ONLY THE 12 PERIMETER SCREWS. (2) When all screws have been removed, gently lift the top panel and attached electronics up and out of the housing. All components of the pressu re scanner are attached t ...

  • Pressure Systems 9016 - page 6

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 5 Viton ® gasket Figure 4 9016 Out of Housing Wiring harness Figure 5 PC-206 Board Phillips head screws Electronic Circuit Board Replacement Your 9016 contains two (2) electronic circuit boards that must be removed and replaced for this upgrade. PC-206 Amplifier/Multiplexer B ...

  • Pressure Systems 9016 - page 7

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 6 Connector P6 Figure 6 PC-280 Board and Connectors Tie-wrap to cut Connector P3 Connector P1 Figure 6a 9016 Top Plate Figure 6b PC-280 Board Three screws to remove PC-280 board PC-280 Ethernet Microprocessor/A-D Board The following procedures should be used for rem oval of th ...

  • Pressure Systems 9016 - page 8

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 7 WARNING: Ensure that the board is oriented the same as the board just removed (connector pins on the same end as the wiring harness) and the gold pins are lined up with and fit easily into the connectors on the DH200s. Figure 7 Tubing Routing Underneath PC-327 Board Retain a ...

  • Pressure Systems 9016 - page 9

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 8 C1 tube Figure 7a PC-327 Board C4 tube C4 tube P1 connection Figure 8 PC-322/323 Boards P3 connection P6 connection Installing the PC-322/323 Boards As previously mentioned, the PC-322 and the PC-323 boards will arrive to you completely connected and may be installed very si ...

  • Pressure Systems 9016 - page 10

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 9 Figure 9 Finding Pin 1 on a PC Board Figure 9a Connectors on 322/323 PCB Pin 1, denoted by square solder pad (on bottom of PC board) Orient red stripe as shown P1 connection on PC-322 board Figure 10 Top Plate to P1 Connection on PC-322 wire wrap, starting near the P6 connec ...

  • Pressure Systems 9016 - page 11

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 10 Figure 11 PC-327 Connection and Cable Tie-down PC-322/323 connection to the PC-327 board Note orientation of red stripe Figure 12 Side View of 9016 Upgrade Figure 13 Top View of 9016 Upgrade (5) Carefully guide the LEDs (on the PC-322 board ) into their respective holes in ...

  • Pressure Systems 9016 - page 12

    Pressure Systems, Inc. 9016 Upgrade Instructions www.PressureSystems.com 11 Final Installation (1) Carefully reinstall the module into the housing, aligning the retaining pins in the housing with holes in the brackets on your PC-322/323 boards. Ensure that none of the wiring harnesses or nylon tubing are pinched. Ensure the Viton ® gask et is flat ...

  • Pressure Systems 9016 - page 13

    Headquarters/Factory : Pressure Sy stems, Inc. 34 Research Drive Hampton, VA 23666 USA Phone: (757) 865-1243 Toll Free: (800) 328-3665 Fax: (757) 865-8744 E-mail: sales@Pres sureSystems.com ...

メーカー Pressure Systems カテゴリー Scanner

Pressure Systems 9016のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 9016の取扱説明書
- Pressure Systemsの製品カード
- パンフレット
- またはPressure Systems 9016の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pressure Systems 9016の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pressure Systems 9016の取り付け説明書、サービスマニュアル、簡易説明書、またはPressure Systems 9016のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pressure Systems 9016の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pressure Systems 9016デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPressure Systems 9016を使用するのを助ける技術的文書のことです。説明書は通常、全てのPressure Systems 9016ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pressure Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pressure Systems 9016の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPressure Systems 9016の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pressure Systems 9016に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pressure Systems 9016デバイスの基本機能を使うにあたってのヒント。 Pressure Systems 9016のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pressure Systems 9016に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPressure Systems 9016のメーカー/サービスへの連絡先に関する情報。

Pressure Systems 9016についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPressure Systems 9016の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPressure Systems 9016で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)