Micon 691の取扱説明書

24ページ 1.47 mb
ダウンロード

ページに移動 of 24

Summary
  • Micon 691 - page 1

    Operation and Installation Instructions 691 LOCK SYSTEM READ GENERAL INSTALLATION GUIDELINES SHEET (FORM NO. 81-600-001) BEFORE PROCEEDING. 1. The MICO 691 System is a supplemental safety device which provides additional brake holding action when used with existing vehicle parking brake . It is not for dynamic service braking. 2. The 691 System mus ...

  • Micon 691 - page 2

    Page SELF ADHESIVE LABELS ................................. 1 INTRODUCTION ...................................... 2 PRINCIPLE OF OPERATION ................................ 2 INSTALLING A 691 SYSTEM ................................ 3 IDENTIFY YOUR BRAKE SYSTEM ............................ 3 - 4 DIMENSIONAL DATA ................................... 5 ...

  • Micon 691 - page 3

    1 THI S N O TI C EM U S T BE AFFIXED O ND A S HI N V I E W O F O PERA T O R Operator must read and understand W arnings and Operating Instructions before using vehicle (Form no. 81-690-032). 691 Brake Loc k T O LOCK: 1. Set parking brake 2. Move lock s witch to LOCK position T O RELEASE: 1. Move lock s witch to RELEASE position 2. Release parking b ...

  • Micon 691 - page 4

    2 Vehicles today have two separate brake systems. One is the service brake system and the other is the parking brake system. The service brake system is used to slow or stop a vehicle during normal operation. The parking brake system is usually cable operated and used to hold the vehicle stationary while parked. Experience has shown that some vehic ...

  • Micon 691 - page 5

    3 There are four steps to installing the 691 System. 1. Mounting 2. Plumbing 3. Wiring 4. Bleeding The 691 System must only be installed by someone with good working knowledge of automotive brake and electri - cal systems. It is important that the installer of the 691 System under - stands fluid types used in various 691 Systems. Read and understan ...

  • Micon 691 - page 6

    4 Typical Split System (1 1/2 x 1/2) Two independent braking systems. One system leads to the front and the rear brakes and the other system leads only to the rear brakes. Identifying Feature: 1. Two lines from master cylinder. 2. Single hose to each front wheel. 3. Two hoses to rear axle. 691 Actuator Position: (1) Front axle (2) Rear axle (3) 4-w ...

  • Micon 691 - page 7

    5 Power Unit Remote Reservoir - (optional) See 691 Accessories on page 19 DIMENSIONAL DATA 1 1/4" Diameter Bore Dual Actuator 1 1/4" Diameter Bore Single Actuator 1 3/4" Diameter Bore Dual Actuator 1 3/4" Diameter Bore Single Actuator User Interface millimeters inches Control Module ...

  • Micon 691 - page 8

    CAUTION Label Pressure Switches 6 Several self adhesive labels are supplied with each 691 Brake Lock. Determine which labels are used in your application and affix in the vehicle cab in view of the operator. See page 1. Actuator 1. Repeat the mounting procedures for each actuator used in your system. 2. Find a location, preferably on the frame rail ...

  • Micon 691 - page 9

    7 Determine the type of brake system on your vehicle, refer to page s3&4 .A l l brake systems in use today require the MICO 691 Actuator(s) be installed after the anti-lock brake valve and combination warning valve if so equipped. Contact MICO, Incorporated if you have questions. Single 691 Brake Lock System 1. Disconnect the existing brake lin ...

  • Micon 691 - page 10

    8 vibration. Common methods used to absorb this shock are coiling the brake tubing or using a short length of purchased brake hose. Follow procedures outlined by the vehicle manufacturer or SAE specifications. 3. Connect the upstream line coming from the master cylinder to the fluid inlet port on one end of the actua- tor. Note that the actuator is ...

  • Micon 691 - page 11

    9 691 Wiring Instructions (Refer to diagrams on pages 14 & 15) The 691 System is designed for use on vehicles with a 12 volt DC, negative ground system. References to "ground" in this literature refer to vehicle chassis ground which is connected to the negative (-) battery terminal. References to "hot" or "positive" ...

  • Micon 691 - page 12

    10 All electrical connections must be completed and the power unit reservoir filled with proper fluid before bleeding. The hydraulic brake system must be bled whenever any line has been disconnected. Although we recommend the use of pressure bleeding equipment when bleeding the system, some vehicle manufacturers do not advise certain bleeding metho ...

  • Micon 691 - page 13

    11 6. Pressure Bleed - There are two options for pressure bleeding the brake system, either using a commercial pressurized bladder type bleeder or by activating the 691 Power Unit. Using commercial bleeder Follow manufacturer's instructions. Using 691 Power Unit A. Activate the 691 System. B. Starting at the actuators and moving outward to fou ...

  • Micon 691 - page 14

    12 To Deactivate Lock Device 1. Disengage other provided holding devices. 2. Switch the user interface to "release" position. The "locked" indicator lamp will deactivate and the power unit will return brake system to static system pressure. 3. Release mechanical parking brake. Using 691 as an Interlock To Activate 1. Bring vehic ...

  • Micon 691 - page 15

    13 NOTES ...

  • Micon 691 - page 16

    691 System Installation Checklist NOTE: As you install the 691 System complete this check list. Upon completion of the 691 installation, retain this checklist with the 691 Operation and Installation Manual. Date installed: _______________ Name of person(s) installing: ______________________________________ Vehicle make:_____________________________ ...

  • Micon 691 - page 17

    o Yes o No 1. Are the wires protected from being hit or kicked and not hanging loose or pulled too tight? o Yes o No o N/A 2. If additional wire was added, is it the correct gauge and color as indicated in the 691 Operation and Installation Manual? o Yes o No 3. Trace each wire, are all wires either connected to something or properly capped off? o ...

  • Micon 691 - page 18

    14 BRAKE LOCK APPLICATIONS Horn Relay User Interface Schematic ...

  • Micon 691 - page 19

    15 INTERLOCK APPLICATIONS Horn Relay User Interface Schematic ...

  • Micon 691 - page 20

    16 TROUBLESHOOTING Before Troubleshooting Unplug wire harness connectors. Check to be sure contacts are clean and making good contact and re - connect. Check the integrity of all wiring at the connectors. Also check to be sure all unused wires are properly capped. LED Display LED Display Explanation Motor Down On when system is releasing pressure. ...

  • Micon 691 - page 21

    17 Situation Cause/Solution (Test in order indicated) When the 691 System is activated, the brakes will not lock-up and the power unit does not run. 1. No electric power. Check the battery, fuse, and wiring connections. 2. High Pressure Switch is inoperative. Activate the 691 System. If "PS1 (lock)" LED is on, unplug pressure switch 1. If ...

  • Micon 691 - page 22

    18 NOTES The 691 System and "Motor Up" LED come on unexpectedly without being activated. 1. The control module is receiving false signals. Be sure stray signals are not being introduced into the external inputs. If the gray wire is not connected to an external input, ensure that it is capped off and not shorting to ground inadvertently. N ...

  • Micon 691 - page 23

    19 691 MODELS AND REPLACEMENT PARTS Part Description Number 02-600-038 Remote Reservoir Kit for Silicone Fluid Models 02-600-049 Integral Reservoir Kit for All Type Fluid Models 32-820-022 11' Extension Harness from Power Unit to Control Module 691 ACCESSORIES TABLE 1 System Model Number Description 691 Fluid Vehicle Fluid Power Unit #1 - High ...

  • Micon 691 - page 24

    20 User Interface Control Module Actuator Actuator Repair Kit Main Harness Reservoir Breather Plug 32-585-007 32-585-006 20-460-013 02-600-035 32-820-021 34-001-089 32-585-007 32-585-006 20-460-014 02-600-036 32-820-021 34-001-089 32-585-007 32-585-006 20-460-018 02-600-042 32-820-021 34-001-089 32-585-007 32-585-006 20-460-012 02-600-034 32-820-02 ...

メーカー Micon カテゴリー Switch

Micon 691のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 691の取扱説明書
- Miconの製品カード
- パンフレット
- またはMicon 691の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Micon 691の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Micon 691の取り付け説明書、サービスマニュアル、簡易説明書、またはMicon 691のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Micon 691の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Micon 691デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMicon 691を使用するのを助ける技術的文書のことです。説明書は通常、全てのMicon 691ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Miconの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Micon 691の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMicon 691の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Micon 691に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Micon 691デバイスの基本機能を使うにあたってのヒント。 Micon 691のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Micon 691に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMicon 691のメーカー/サービスへの連絡先に関する情報。

Micon 691についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMicon 691の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMicon 691で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)