-
Avaya X330W-2DS1 - page 1
A vaya X330W -2DS1 Access Router Module Quick Start Guide N N o o t t e e : The X330W AN expansion modules can be installed in the following A vaya P330 switches: • P333T , P334T , P332MF , P333R, P333R-LB, P333T -PWR – Embedded S/W version 3.9 or higher Y ou can see the Embedded Software versions of the switch using the dir [mod_num] CLI comma ...
-
Avaya X330W-2DS1 - page 2
Important Safety Information Before installing or r emoving any components of a device, or carrying out any maintenance work, you must read the safety information pr ovided. CAUTION: T o avoid damage from static, only hold the W AN Expansion Router Module by the edges. Do not touch the top or bottom of the circuit boar d. If possible, wear a wrist- ...
-
Avaya X330W-2DS1 - page 3
Unpack the Module Check the package contents for the following: Equipment • One X330W AN Access Router Module. L Connection cables are not supplied. Documentation • A vaya X330W AN Access Router Modules Quick Start Guide (this document). • A vaya X330W AN Access Router Modules Release Notes. • A vaya X330W AN Access Router Modules Documenta ...
-
Avaya X330W-2DS1 - page 4
Insert the Module T o insert an X330W AN into an A vaya P330 switch: 1. Remove the blanking plate or other expansion module (if installed). 2. Insert the W AN expansion module gently into the slot, ensuring that the Printed Circuit Board (PCB) is aligned with the guide rails. L The PCB fits into the guide rails and not the metal base plate. 3. Pres ...
-
Avaya X330W-2DS1 - page 5
4 Connect the Ports Connecting the E1/T1 Ports T o connect a T1/E1 module to a network, use a straight-through RJ-48C-to-RJ-48C cable to connect the E1/T1 port to an RJ-48C wall jack. Connecting the Ethernet Port A UTP Category 5 cable must be connected to the 100Base-TX port, via an RJ45 connector . The maximum UTP cable length connected to the 10 ...
-
Avaya X330W-2DS1 - page 6
5 Configure the Module L Before you can set up the X330W AN module you must power on and set up the A vaya P330 stack as described in the A vaya P330 User ’s Guide. L Before using the X330W AN module you must assign an IP addr ess via the Command Line Interface (CLI) or via a T elnet session to the switch where the X330 is inserted. The following ...
-
Avaya X330W-2DS1 - page 7
L The console interface configured with the interface Console command must be on a differ ent subnet from the r outer interfaces. 6. Use the following commands to set the baud rate, ppp authentication, ppp chap-secret and ppp timeout requir ed to match your remote station if they dif fer from the default values: L The default values are shown in bo ...
-
Avaya X330W-2DS1 - page 8
Configuring Loopback Interfaces L All CLI commands mentioned in this section are described in the A vaya P330 Reference Guide. T o configure Loopback interfaces: 1. Use the interface loopback <loopback number> command to enter the Interface Loopback mode. For example, typing interface loopback 1 configures a loopback with a Loopback interface ...
-
Avaya X330W-2DS1 - page 9
Configuring E1/T1 Interfaces L All CLI commands mentioned in this section are described in the A vaya P330 Reference Guide. T o configure E1/T1 interfaces: 1. Use the show controllers command to check if your controller ’s mode is configured as E1 or T1. Use the ds1-mode <e1 | t1> command to change the controller ’s mode from E1 to T1 or ...
-
Avaya X330W-2DS1 - page 10
Changing the Primary Management Interface (pmi). L The default pmi is the first interface you define. T o change the pmi: 1. Enter one of the interface contexts as explained before. 2. If there no ip assigned on that interface use the | ip address <ip_ addr>< net- mask> command. 3. Use the ip routing-mode rt_primary_mgmt command to set ...
-
Avaya X330W-2DS1 - page 11
X330WAN Default Settings The default settings for the X330W AN and its ports are determined by its embedded software. These default settings are subject to change. Newer versions of the softwar e for the X330W AN can be downloaded from the A vaya Network Software Download W eb site (http://www .avayanetwork.com). If you wish to change the default p ...
-
Avaya X330W-2DS1 - page 12
Run the W eb-Based Manager (optional) L T o configure the A vaya X330W AN you can use the P330 W eb-based Manager in addition to using the CLI. System Requirements Minimum hardwar e and Operating System requir ements are: • Pentium® II 400 Mhz-based computer with 128 Mb of RAM • Screen r esolution of 1024 x 768 pixels • Microsoft® Internet ...
-
Avaya X330W-2DS1 - page 13
L If the network manager has configured the system the plug-in should be installed auto- matically . If the plug-in is not installed automatically , there ar e three ways to install the plug-in manually: • Either install the plug-in fr om the CD as follows: 1. Close all unnecessary applications on your PC. 2. Insert the “A vaya P330 Documentati ...
-
Avaya X330W-2DS1 - page 14
Documentation and Online Help Refer to the A vaya X330W AN Documentation and Utilities CD for full instructions. ...
-
Avaya X330W-2DS1 - page 15
Notes ...
-
Avaya X330W-2DS1 - page 16
Contact Information T o contact A vaya technical support: From the United States: Please call 1-800-237-0016, press 0, then pr ess 73300. From outside the United States: EMEA (Europe, Middle East and Africa). Email: csctechnical@avaya.com AP (Asia Pacific). Email: sgcoe@avaya.com CALA (Caribbean and Latin America). Email: caladatasupp@avaya.com Hot ...
Avaya X330W-2DS1についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもAvaya X330W-2DS1の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAvaya X330W-2DS1で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。