Audiovox PRO-9056の取扱説明書

19ページ 0.41 mb
ダウンロード

ページに移動 of 19

Summary
  • Audiovox PRO-9056 - page 1

    128-7762 1 of 19 The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text. Note : The method of manual override can either be selected to operate from the v ...

  • Audiovox PRO-9056 - page 2

    128-7762 2 of 19 T o program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Features First Press and release the valet switch 1 ...

  • Audiovox PRO-9056 - page 3

    128-7762 3 of 19 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps 1st Defrost Output Not Available 2nd RF S t art Chirp Not Available 3rd Run Time 5 Mins 10 Mins 15 Mins 20 Mins 4th ...

  • Audiovox PRO-9056 - page 4

    128-7762 4 of 19 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote S tart Selectable Features First Press the valet switch one time 1 chirp = defrost output pu ...

  • Audiovox PRO-9056 - page 5

    128-7762 5 of 19 This Remote S tart System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the RF signal is ...

  • Audiovox PRO-9056 - page 6

    128-7762 6 of 19 IMPORT ANT! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MUL TI PIN INPUT / OUTPUT HARNESS INT O THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HA VE BEEN MADE. AFTER SELECTING YOUR T ARGET WIRES AS DEFINED BELOW , DISCONNECT THE NEGA TIVE BA TTERY CABLE FROM THE VE- HICLE BA TTERY PRIOR TO MAKING ANY CONNECTIONS. WIR ...

  • Audiovox PRO-9056 - page 7

    128-7762 7 of 19 SEE NEUTRAL S T ART SAFETY TEST FOR FURTHER DET AILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN" and the "ST ART" or CRANK" positions and will have 0 volts ...

  • Audiovox PRO-9056 - page 8

    128-7762 8 of 19 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to the "OFF" and "ST ART" or ...

  • Audiovox PRO-9056 - page 9

    128-7762 9 of 19 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle. This wire provides a + 12 Volt output when the ignition key is turned to the “ON” position, and 0 Vol ...

  • Audiovox PRO-9056 - page 10

    128-7762 10 of 19 the applications described below , a relay will be required. The Light Blue wire can be used to accommodate the following situations: A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote S tart activation period, then vibration from the running vehicle can cause the al ...

  • Audiovox PRO-9056 - page 11

    128-7762 11 of 19 cases will operate properly from one multi coil pack regardless of the number of cylinders. If the vehicle has a single coil unit for each cylinder , it may be necessary to connect this wire to more than one cylinder for proper tach reference. See multi coil wiring detail shown later in this manual for additional information. T ac ...

  • Audiovox PRO-9056 - page 12

    128-7762 12 of 19 2 Pin T ransponder Control Output: (Y ellow Connector) This output is intended to allow the control of a transponder bypass interface module or transponder bypass relay . The system also allows sof tware selections to control the way in which this output oper- ates, see remote start feature # 10 for setting this output. When the u ...

  • Audiovox PRO-9056 - page 13

    128-7762 13 of 19 columns. The Green/Black wires should be connected to the negative (-) terminal of the respective cylinder number which appears in any of the circles. 2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil pack. For 8 cylinder , four coil systems, connect to any of the three co ...

  • Audiovox PRO-9056 - page 14

    128-7762 14 of 19 1. Set the vehicle parking brake. 2. Block the drive wheels to prevent vehicle movement. 3. T emporarily disconnect the Brown/Black positive shut down wire from the vehicle's brake switch. 4. Sitting in the vehicle, start the engine using the vehicle's ignition key . 5. S tep on the brake pedal and shift the gear selecto ...

  • Audiovox PRO-9056 - page 15

    128-7762 15 of 19 AUDIOVOX ADVISES THA T YOU MAINT AIN THE F ACT ORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available. NOTE: When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the ...

  • Audiovox PRO-9056 - page 16

    128-7762 16 of 19 C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D. Cut this wire and connect the ignition cylinder side to the Remote S tart Negative Safety Shut down Wire Gray/ Black, using a 4002 series diode as shown above. NOTE: A second 4002 series diode may be required to maintain the integr ...

  • Audiovox PRO-9056 - page 17

    128-7762 17 of 19 ...

  • Audiovox PRO-9056 - page 18

    128-7762 18 of 19 THIS PAGE LEFT BLANK INTENTIONALLY ...

  • Audiovox PRO-9056 - page 19

    128-7762 19 of 19 © 2006 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-7762 ...

メーカー Audiovox カテゴリー Automobile Accessories

Audiovox PRO-9056のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PRO-9056の取扱説明書
- Audiovoxの製品カード
- パンフレット
- またはAudiovox PRO-9056の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Audiovox PRO-9056の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Audiovox PRO-9056の取り付け説明書、サービスマニュアル、簡易説明書、またはAudiovox PRO-9056のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Audiovox PRO-9056の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Audiovox PRO-9056デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAudiovox PRO-9056を使用するのを助ける技術的文書のことです。説明書は通常、全てのAudiovox PRO-9056ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Audiovoxの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Audiovox PRO-9056の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAudiovox PRO-9056の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Audiovox PRO-9056に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Audiovox PRO-9056デバイスの基本機能を使うにあたってのヒント。 Audiovox PRO-9056のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Audiovox PRO-9056に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAudiovox PRO-9056のメーカー/サービスへの連絡先に関する情報。

Audiovox PRO-9056についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAudiovox PRO-9056の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAudiovox PRO-9056で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (1)

jose

como modificar la portada y facilitar el acceso al encender