日本語 dropdown-ico

Kenmore 721.80042の取扱説明書

20ページ 0.84 mb
ダウンロード

ページに移動 of 20

Summary
  • Kenmore 721.80042 - page 1

    Models/Modelos 721.80032 721.80033 721.80034 721.80039 721.80042 721.80043 721.80044 721.80049 Read and save these installation instructions. Lea y guarde estas instrucciones de instalaci6n INSTALLATION INSTRUCTIONS INSTRUCCIONES DE INSTALACION _. I _ _> _ I _ J _J Microwave Hood Combination Combinaci6n Microondas Campana Part No. MFL39433001 Se ...

  • Kenmore 721.80042 - page 2

    YOUR SAFETY FIRST BEFORE YOU START • Proper installation is the installer's responsibility! - Read the entire manual before you begin. - The model number label is located on the oven front. See Figure 1. - Mounting plate is located on back side of microwave oven. See Figure 2. BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS: Model Number L ...

  • Kenmore 721.80042 - page 3

    YOUR SAFETY FIRST • THIS APPLIANCE MUST BE GROUNDED! - If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. • Place the plug into a properly installed and grounded outlet. ...

  • Kenmore 721.80042 - page 4

    YOUR SAFETY FIRST • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. - Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath. - ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, ...

  • Kenmore 721.80042 - page 5

    THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector (for roof vented or wall vented installation) Not Actual Size One power cord clamp and One dark-colored mounting screw (to hold the power cord) Actual Size One power cord clamp bushing - Actual ...

  • Kenmore 721.80042 - page 6

    PARTS, TOOLS, MATERIALS YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heavy material for covering the counter top. Clear tape (for taping the templates to the wall) Stud finder or thin nail. Saber saw (for cutting vent holes for roof or wall venting) Phillips screwdriver (for the screws) Pencil Flat blade scr ...

  • Kenmore 721.80042 - page 7

    STEP 1: PREPARE THE ELECTRICAL CONNECTIONS _k WARNING _k AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. NOTE: The outlet should be on a circuit dedicated to the microwave oven 120V, 60Hz., AC only, with a 20ampere fused electri ...

  • Kenmore 721.80042 - page 8

    STEP 2: PREPARE THE VENTING SYSTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 9, page 9. WARNING - FIRE HAZARD THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways: Roof Venting If your oven is located on an outside wall ...

  • Kenmore 721.80042 - page 9

    STEP 2: PREPARE THE VENTING SYSTEM STANDARD FITTINGS NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper sticking. DUCT LENGTH The total length of the duct system, including straight duct, elbow ...

  • Kenmore 721.80042 - page 10

    STEP 3: PREPARE THE VENTING BLOWER Your microwave oven is shipped with the blower assembled for room venting (recirculating). You need to adjust the blower if you want wall vented or roof vented installation. WARNING ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT. DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blowe ...

  • Kenmore 721.80042 - page 11

    STEP 3: PREPARE THE VENTING BLOWER WALL VENTED INSTALLATION: 1. Remove one blower unit mounting screw and two blower plate screws. Remove the blower plate from cabinet. See Figure 12. 2. Carefully lift the blower unit out of the microwave oven. Disconnect the blower wire from connector. See Figure 13. 3. Use side cutters or tin snips to cut and rem ...

  • Kenmore 721.80042 - page 12

    STEP 3: PREPARE THE VENTING BLOWER ROOF VENTED INSTALLATION: 1. Remove one blower unit mounting screw and two blower plate screws. Remove the blower plate from cabinet. See Figure 18. blower plate mounting screws 2. Carefully lift the blower unit out of the microwave oven. 3. Rotate blower unit 90 ° so the exhaust ports face the top of the cabinet ...

  • Kenmore 721.80042 - page 13

    STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION MEASURE AND TACK / TAPE UP THE TEMPLATE 1. Using a plumb line and (metal) measuring tape, find and mark the vertical center line (_)on the back wall, as in Figure 22. 2. Find and mark one or two points where the studs are on the wall (Studs are normally 16 inches apart.) and then measure a ...

  • Kenmore 721.80042 - page 14

    STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION DRILL THE HOLES IN THE WALL AND UPPER CABINET. WARNING BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL. Electrical wires could be concealed behind the wall covering and if the drill hits them you could get an electric shock. 1. Find the points on the mounting plate labeled "A", ...

  • Kenmore 721.80042 - page 15

    STEP 5: INSTALL THE MOUNTING PLATE TO THE WALL THE OVEN MUST BE CONNECTED TO AT LEAST ONE WALL STUD. 1. Draw a vertical line on the wall at the center of the 30" wide space. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are against the bottom of the cabinet. Line up th ...

  • Kenmore 721.80042 - page 16

    STEP 5: INSTALL THE MOUNTING PLATE TO THE WALL TO PREPARE THE REAR WALL CUTOUT OPENING AND EXHAUST ADAPTOR/MOUNTING PLATE FOR WALL VENTING AND ROOF VENTING: NOTE: If room vented installation is used, skip this step. 1. Using the Wall-template.This template will give the location and size of the box cutout for the rear wall duct as described in step ...

  • Kenmore 721.80042 - page 17

    STEP 6: A TTACH THE OVEN TO THE WALL A WARNING A You will need two people to lift this microwave. Failure to use more than one person could result in personal injury. 1. Carefully lift microwave oven and hang it on support tabs (See Figure 26) at the bottom of the mounting plate. Reaching through upper cabinet, thread power supply cord through the ...

  • Kenmore 721.80042 - page 18

    STEP 6: ATTACH THE OVEN TO THE WALL 5. Roof vented installation: See Figure 32. Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See "PREPARE THE VENTING SYSTEM," STEP 2 on the page 8. Use caulking to seal exterior roof opening around the exhaust c ...

  • Kenmore 721.80042 - page 19

    MEMO 19 ...

  • Kenmore 721.80042 - page 20

    Printed in China ...

メーカー Kenmore カテゴリー Microwave Oven

Kenmore 721.80042のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 721.80042の取扱説明書
- Kenmoreの製品カード
- パンフレット
- またはKenmore 721.80042の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Kenmore 721.80042の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Kenmore 721.80042の取り付け説明書、サービスマニュアル、簡易説明書、またはKenmore 721.80042のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Kenmore 721.80042の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Kenmore 721.80042デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKenmore 721.80042を使用するのを助ける技術的文書のことです。説明書は通常、全てのKenmore 721.80042ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Kenmoreの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Kenmore 721.80042の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKenmore 721.80042の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Kenmore 721.80042に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Kenmore 721.80042デバイスの基本機能を使うにあたってのヒント。 Kenmore 721.80042のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Kenmore 721.80042に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKenmore 721.80042のメーカー/サービスへの連絡先に関する情報。

Kenmore 721.80042についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもKenmore 721.80042の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKenmore 721.80042で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)