JAI TM-2016-8/8CLの取扱説明書

44ページ 1.67 mb
ダウンロード

ページに移動 of 44

Summary
  • JAI TM-2016-8/8CL - page 1

    69-0093 Rev . B TM-2016-8/8CL Pr ogressive Scan Shutter Cameras Operation Manual ...

  • JAI TM-2016-8/8CL - page 2

    Page ii ...

  • JAI TM-2016-8/8CL - page 3

    Page iii Notice The material contained in this manual con sists of information that is proprietary to JAI, Inc., and m ay only be used by the pur - chasers of the product. JAI, Inc. makes no warran ty for the us e of its product and assumes no responsibili ty for any errors which may appear or for damages resultin g from the use of the information ...

  • JAI TM-2016-8/8CL - page 4

    Page iv W ARNING Changes or modifications to this unit not expr essly approved by the party responsible for FCC compliance could void the user’ s authority to operate the equipment. TM-2016-8/8CL Operation Manual JAI, Inc. 625 River Oaks Parkway San Jose, CA 95134 T el:(408 ) 383-0300 T el:(800 ) 445-5444 Fax:(408) 383-0301 E-mail: imaging@ jai.c ...

  • JAI TM-2016-8/8CL - page 5

    Page v T able of Content s T able of Content s T able of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v List of Figur es . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii List of T ables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • JAI TM-2016-8/8CL - page 6

    Page vi T able of Content s 3.7.1 Programmab le Look-Up T able (LUT) and Knee Control . . . . . . . . . . . . . . 22 3.8 Scan Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.8.1 Full Progressive Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.8.2 T wo-Row ...

  • JAI TM-2016-8/8CL - page 7

    Page vii List of Figures List of Figures FIGURE 1. TM-201 6-8 System Configur ation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FIGURE 2. Camera Link System Conf iguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FIGURE 3. Rear Panel V iew of Digital Connector . . . . . . . . . . . . . . . . . . . . . . . ...

  • JAI TM-2016-8/8CL - page 8

    Page viii List of Figures ...

  • JAI TM-2016-8/8CL - page 9

    Page ix List of T ables List of T ables T ABLE 1. 12-Pin Connector (TM-2016-8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 T ABLE 2. 12-Pin Connector (TM-2016-8CL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 T ABLE 3. 31-Pin Connector (MP21 1-031-1 13-4300) . . . . . . . . . . . . . . . . . . . . . . . . 8 ...

  • JAI TM-2016-8/8CL - page 10

    Page x List of T ables ...

  • JAI TM-2016-8/8CL - page 11

    May 31, 2007 TM-2016-8 and TM-2 016-8CL Progressive Scan Shutte r Camera TM-2016-8 and TM-2016-8CL Pr ogr essive Scan Shutter Camera Operation Manual 1 Introduction 1.1 Product Description The JAI, Inc. TM-2 016-8 * is a high-resolution, high-speed mon o chrome progressive scan CCD camera. The interline-transfer type CCD perm its full verti cal and ...

  • JAI TM-2016-8/8CL - page 12

    Page 2 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Introduction 1.2 Features • Miniaturized and lightweight The printed circuit boards in the TM-20 16-8 have been arranged based on a new design philoso phy that creates modular electronics for the camera, giving i t flexibility . In addition, the use of miniature solid-state comp on ...

  • JAI TM-2016-8/8CL - page 13

    Page 3 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Introduction The TM-2016-8 captures async reset images and provides single-shot video output with single FDV . This makes it simpler for an ordinary fr ame grabber to capture the async reset images. • Read Out Inhibit (ROI) When Asynchronous no-del ay shutter mode is sel ected, it a ...

  • JAI TM-2016-8/8CL - page 14

    Page 4 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Introduction 1.4 System Configuration FIGURE 1. TM-2016-8 Sy stem Configuration Figure 1 below presents a t ypical system configurati on for the TM-2016-8 camera. FIGURE 2. Camera Link System Con figuration Figure 2 below presents a typical system configuration for the Camera Link ca ...

  • JAI TM-2016-8/8CL - page 15

    Page 5 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Inst allation 2 Inst allation The following instructions are pro vided to help you to set up your camera quickly and easily . W e suggest that you read through th ese instructions before you unpack and set up your camera system. 2.1 Getting St arted 2.1.1 Unp acking Instructions W e r ...

  • JAI TM-2016-8/8CL - page 16

    Page 6 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Inst allation • Make sure the flow of heat from the camera case to the bracket is not blocked by a non-conductive material lik e plastic. • Make sure the camera has enough open space aro und it to facilitate the free flow of air . Please contact JAI, Inc. at (800) 445-5444 or sen ...

  • JAI TM-2016-8/8CL - page 17

    Page 7 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Inst allation 2.2.2 (b) 12-Pin Connector (Camer a Link models) The TM-2016-8 Camera Link cameras have a 12-pin Hirose connecto r for power input and signal I/O. Pin #1 is Ground and pin #2 is +12V DC. The pinout table is show n below . For TM-2 016-8 Camera Link model cameras, serial ...

  • JAI TM-2016-8/8CL - page 18

    Page 8 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Inst allation 2.2.2 (d) Camera Link Connector (Camera Link only) The TM-2016-8 Camera Link models have a 26-pi n MDR26 connector on the rear panel to output Camera Link data. The connector pin-out is sh own in T able 4 below . T ABLE 3. 31-Pin Connector ( MP21 1-031 -1 13-4 300) a a. ...

  • JAI TM-2016-8/8CL - page 19

    Page 9 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Inst allation 2.2.2 (e) Analog Output Connector The TM-2016-8 has a BNC connector on the rear panel to output analog video data. See Section 2.2.4 on page 10 for additional information on analog video output. T ABLE 4. Connector and Pinout Config urations Camera Link Connector MDR 26- ...

  • JAI TM-2016-8/8CL - page 20

    Page 10 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Inst allation 2.2.3 Shutter S peed Control Dial (TM-2016-8 only) 2.2.4 RS-232 Commu nication Cable (TM-2016-8 only) FIGURE 4. Serial Communication Cable RS- 232B-12 The RS-232 controller set CS-232E includes the RS-2 32B-12 interface cable, th e software disk, and a quick-start card ...

  • JAI TM-2016-8/8CL - page 21

    Page 1 1 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Inst allation 2.2.5 Digit al Output Cable (TM-2016-8 onl y) The TM-2016-8 camera uses the cable 30DG-02 from JAI, Inc. as a digital output cable . This cable has a 31-pin AirBorn connector on the camera end and a 37-pin D-sub male connect or on the other end. Contact your JAI, Inc. ...

  • JAI TM-2016-8/8CL - page 22

    Page 12 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Inst allation 2.2.6 Camera Link Cable (TM-2016-8CL only) The Camera Link cable assem bly (26CL-02-26) has a 26-pin MDR26 connector on both ends. This is a straight-through cable. The pin-out confi guration is shown in T able 4 on page 9. Note: For the TM-2016-8CL model, serial commu ...

  • JAI TM-2016-8/8CL - page 23

    Page 13 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Inst allation 2.2.7 (b) JAI, Inc. Power Cables If you are using JAI, Inc. po wer cables such as the 12P-02S, please re fer to the 12-pin con nector pin-out diagram in “12-Pin Connector (TM-2016-8)” on page 6. The cable pin-out diagram is shown in Figure 6 below . The color-coded ...

  • JAI TM-2016-8/8CL - page 24

    Page 14 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Inst allation 1. Rotate the connector while applying slight pressure until the keyw ays line up. 2. Press the connector into place until firmly seated. 3. Plug the power cord into the 100V AC socket. This will power the camera up. 2.2.8 Att aching the Analog V ideo Output When conne ...

  • JAI TM-2016-8/8CL - page 25

    Page 15 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Operation 3 Operation 3.1 Camera Rear Panel (TM-2016-8) 3.1.1 Up/Down Switch The Mode Selection switch works in conjunction with the Up/D own switch. Refer to T able 6 ab ove for information on the Up /Down switch. 3.1.2 Digit al Output Connector Refer to Section 2.2.2 (c on page 7 f ...

  • JAI TM-2016-8/8CL - page 26

    Page 16 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Operation the RS-232 interface will over -write the rear panel switch se ttings of the camera. The table below shows details on various modes. 3.2 Camera Link Rear Panel (TM-2016-8CL) 3.2.1 Digit al Output Connector Refer to Section 2.2.2 (d on page 8 for informati on on digital out ...

  • JAI TM-2016-8/8CL - page 27

    Page 17 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Operation 3.2.2 Analog Output Connecto r The TM-2016-8CL camera has a BNC connector on th e rear panel to output analog vi deo data. 3.2.3 Power and External Sync Connector Refer to Section 2.2.2 on page 6 for informati on on the power and extern al sync. connectors. ...

  • JAI TM-2016-8/8CL - page 28

    Page 18 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Operation 3.3 Progressive Scanning Standard TV -system scanning is 525 lines interlace s canning as specified in the RS-170 protocol. Every other horizontal line (odd lines and even lines) is s canned at a 60Hz rate per field, and the scanning is completed with two fields (one fr am ...

  • JAI TM-2016-8/8CL - page 29

    Page 19 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Operation 3.5 Integration The CCD imager of the TM-2016-8 can be exposed for longer than the normal scan timing of 1/8 sec. This integration feature provides ext ra sensitivity for dark-environment application s. The progressive scan imager permits a full fram e of resolution in non- ...

  • JAI TM-2016-8/8CL - page 30

    Page 20 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Operation For the progressive format, one frame of video outp ut will start from the rising edge of the pulse width control. As Asynchronous m ode with external pulse i nput high, the video out put will be disabled as the camera continues discharging the CCD image, providing black v ...

  • JAI TM-2016-8/8CL - page 31

    Page 21 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Operation This helps a single frame grabber to process mu ltiple images in pipeline processi ng (sequential process). 3.6.3 Internal Shutter S peed Control The speed control ranges from 1/30 to 1/8,00 0 sec. The video signal starts wi th int ernal VINIT . W ith the internal mode sele ...

  • JAI TM-2016-8/8CL - page 32

    Page 22 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Operation 3.7 Dynamic Range Control The typical interline transf er CCD has fixed noise levels based on dark current (thermal or KT noise), pattern noise, and the operating cl ock speed. In general, the total noise level of the 20 MHz pixel clock CCD at room temperature is around 20 ...

  • JAI TM-2016-8/8CL - page 33

    Page 23 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Operation FIGURE 7. Look-Up T able 3.8 Scan Modes The TM-2016-8 supports the following scan mode s: 3.8.1 Full Progre ssive Scan Normal scanning mode the TM -2016-8 is for 1920 x 1080 pixels. The standard speed with single- channel output is 8 frame/sec at th e pixel clock of 20 MHz. ...

  • JAI TM-2016-8/8CL - page 34

    Page 24 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Operation 3.10 Camera T iming Chart s Model: TM-2016-8 Operation Mode: 8 frame / sec Master Clock: 40.00 MHz, M= 25 nsec Pix el Clock: 20.00 MHz, P= 50 nsec 1. Pix el Clock and Digital Data Tc d Td c Th d T cd: Clock to Data Ready T dc: Data Ready to Next Clock Thd: Data Hold Time P ...

  • JAI TM-2016-8/8CL - page 35

    Page 25 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Operation Model: TM-2016-8 Operation Mode: 8 Fr ames/Second Master Clock: 40.0 MHz, M= 25.0 nsec Pix el Clock: 20.0 MHz, P= 50.0 nsec 3. External Reset Timing 4. Async Reset T iming External VD Internal VD FDV Digital Data Analog Video VINIT T rigger Internal VD FDV Digital Data Anal ...

  • JAI TM-2016-8/8CL - page 36

    Page 26 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Operation 3.10.1 Pixel Clock Locking (optional) * For multiple-camera applications such as 2D or 3D measurement, multiple-camera inspection, a parallel digital data input cap ability is important. The high resolution and precision measu rement requires that camera data be consistent ...

  • JAI TM-2016-8/8CL - page 37

    Page 27 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera T roubleshooting 4 T roubleshooting 4.1 Problems and Solutions Following are troublesho oting tips for common problem s. In general, problems can easily b e solved by following these instructions. If the following remedies fai l to offer a solution to your problems, please contact a ...

  • JAI TM-2016-8/8CL - page 38

    Page 28 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera T roublesh ooting 4.2 Information a nd Support Resources For further inf ormation and support: Phone: (408) 383-0300 (800) 445-5444 (24- hour message access) Fax: (408) 383-0301 E-mail: imaging@jai .com Mail: JAI, Inc. Sales Department 625 River Oaks Parkway San Jose, CA 95134 A TTN ...

  • JAI TM-2016-8/8CL - page 39

    Page 29 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Appendix 5 Appendix 5.1 Specifications T ABLE 7. TM-2016-8 and TM-2016-8CL Product S pecifications T able Model TM-2016-8 and TM-2 016-8CL Imager 1”, 7.4µm x 7.4µm progressi ve scan interline transfer CCD Active Pixels 1920 (H) x 1080 (V) Active Area 15.90 (H) mm x 8.61 (V) mm Ce ...

  • JAI TM-2016-8/8CL - page 40

    Page 30 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Appendix 5.1.1 Physical Dimensions FIGURE 8. Physical Dimensions (TM-2016 -8) FIGURE 9. Physical Dimensions (TM-2016 -8CL) 2 6 7 1 F E D 9 8 4 C G B A 25.4 [1.00] 7.0 [0.28] 15.3 [0.60] 22.0 [.87] 4X 18.0 [0.71] 2X M6 44.0 [1.73] 1/4-20 SOC HD CAP SCR 2X M3 X 6.0 [0.24] 19.0 [0.75] ...

  • JAI TM-2016-8/8CL - page 41

    Page 31 TM-2016-8 and TM-2016-8CL Progressive Scan Shutter Camera Appendix 5.1.2 Spe ctral Response FIGURE 10. Spectra l Response 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 400 450 500 550 600 650 700 750 800 850 900 950 1000 Wavelength (nm) Absolute Quantum Efficiency ...

  • JAI TM-2016-8/8CL - page 42

    Page 32 TM-2016-8 and TM-2016-8CL Progressi ve Scan Shutter Camera Appendix ...

  • JAI TM-2016-8/8CL - page 43

    www.jai.com ...

  • JAI TM-2016-8/8CL - page 44

    JAI, Inc. 625 River Oaks Pkwy . San Jose, CA 95134 T el: 408-383-030 0 T el: 800-445-544 4 Fax: 408-383-0301 www.jai.com 69-0093 Rev. B Email: imaging@jai.com ...

メーカー JAI カテゴリー Digital Camera

JAI TM-2016-8/8CLのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TM-2016-8/8CLの取扱説明書
- JAIの製品カード
- パンフレット
- またはJAI TM-2016-8/8CLの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、JAI TM-2016-8/8CLの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、JAI TM-2016-8/8CLの取り付け説明書、サービスマニュアル、簡易説明書、またはJAI TM-2016-8/8CLのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、JAI TM-2016-8/8CLの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

JAI TM-2016-8/8CLデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJAI TM-2016-8/8CLを使用するのを助ける技術的文書のことです。説明書は通常、全てのJAI TM-2016-8/8CLユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

JAIの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. JAI TM-2016-8/8CLの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJAI TM-2016-8/8CLの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。JAI TM-2016-8/8CLに関してこのドキュメントで見つけることができる全てのヒントの目次
3. JAI TM-2016-8/8CLデバイスの基本機能を使うにあたってのヒント。 JAI TM-2016-8/8CLのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。JAI TM-2016-8/8CLに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJAI TM-2016-8/8CLのメーカー/サービスへの連絡先に関する情報。

JAI TM-2016-8/8CLについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJAI TM-2016-8/8CLの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJAI TM-2016-8/8CLで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)