-
Bogen X600 - page 1
Black Max ™ Amplifier X300, X450, & X600 Models Installation and Use Manual © 200 1 Bogen Communications, Inc. All rights reserved. 54-2063-0 1 R2 0 1 09 ...
-
Bogen X600 - page 2
Notice Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing. How ev er , information is subject to change. Important Safety Information W ARNING: T o Reduce The Risk of Fire Or Electric Shock, Do Not Expose This Apparatus T o Rain Or Moistur e. Alwa ys f ollow these basic safety pr eca ...
-
Bogen X600 - page 3
Contents Page INTRODUCTION ................................................................................................................ 1 Package Contents ............................................................................................................... ................. 1 P ANEL DESCRIPTIONS........................................ ...
-
Bogen X600 - page 4
Intr oduction Bogen's Black Max™ amplifiers deliver on what pr ofessional sound installers need most: Po wer and Reliability . Po w e r With three diff erent models (X600, X450, and X300), the Black Max series pr ovides 2 independent channels of amplification at 600W , 450W , and 300W per channel into 70V constant voltage speak er loads safe ...
-
Bogen X600 - page 5
P anel Descriptions Black Max Fr ont P anel 1 . Status Indicators The Status LEDs are m ulti-purpose indicators, one for each channel. Green - Amplifier is on and operating normally . Amber - Amplifier is in low-pow er consumption Sleep Mode. Red - Amplifier has protected itself due to a fault condition. 2. Signal Indicators Three illuminate gr een ...
-
Bogen X600 - page 6
P anel Descriptions Black Max Rear P anel 1 . High-Impedance Balanced Inputs Pluggable 3-position terminal strips allow for easy installation and pr ovide con v enient connections to high- impedance balanced inputs. 2. Input Le vel Contr ols Continuously variable input le vel contr ols. 3. Lo-Cut Filters Roll off frequencies belo w 60Hz (2nd order) ...
-
Bogen X600 - page 7
Installation Mechanical Components 1 . Rack Ears Prior to installing the amplifier in to a 1 9" rack, you will need to attach the rack ears. Remove and sa v e the 6 front most co ver scr e ws on each side panel of the amplifier . Position the rack ears as shown and attach using the 6 scre ws. 2. Dust Filter Insert the dust filter into the fan ...
-
Bogen X600 - page 8
Installation V entilation The Black Max amplifiers wer e designed to be placed on a table or rack-mounted. For rack-mounted applica- tions, the amplifiers can be stacked one on top of the other f or maximum use of the rack space a vailable with- out any extra, empty rack spaces between them. An open air space of at least 4" must be pr ovided a ...
-
Bogen X600 - page 9
Connections Speakers 70V "T ransformer -Coupled" Speakers The Black Max series was designed to drive onl y 70V constant volt- age type speak er loads. The use of low-impedance speakers ma y cause the amplifier to engage its protection cir cuits and shut do wn or limit amplifier function. The speak er terminals can accept up to a # 1 0 A W ...
-
Bogen X600 - page 10
Sequential T urn-On Sequential T urn-On Oper ation Black Max amplifiers contain a sequential turn-on featur e that is designed to turn on a bank of Black Max ampli- fiers, one at a time, in sequence with appr oximatel y 1 second between each amplifier . This type of sequencing of pow er is necessar y in large systems where the in-rush cur rent of a ...
-
Bogen X600 - page 11
Operation Fr ont Contr ols & Indicators P o wer Switch The Po wer Switch f or the Black Max amplifier is located on the fr ont of the unit. Press the "I" side of the switch to turn the unit ON. The amplifier will begin its pow er up process once turned on. If the amplifi- er is set up for pow er sequencing (see the section on pow er s ...
-
Bogen X600 - page 12
Operation Sleep Switch The Black Max amplifier includes a sleep mode featur e that greatl y reduces the po wer consumption of the amplifier after it has been idle (no audio activity) for mor e than 3 minutes. Any audio activity present at the input will pow er up the amplifier instantaneously and noiseless- ly , so that there is no loss of audio . ...
-
Bogen X600 - page 13
T r oubleshooting 10 • Po wer Switch off • Break er (P ow er Switch) tripped - T urn off, then turn bac k on • Po wer Sequencing Switch set wr ong - Check Sequential T urn-On section for pr oper conf iguration PROBLEM CONDITION CAUSE Rear Po wer Status LED is amber . SEQUENCING NO T FUNCTIONING CORRECTL Y Master amplifier ON (Rear Po wer Stat ...
-
Bogen X600 - page 14
Specifications * Both channels driven at nominal line voltage 1 20V AC, 60Hz. 11 Power Output* 600W /Ch @ 70V 450W / Ch @ 70V 300W / Ch @ 70V Input Sensitivity 1 V S/N Ratio (20K BW) 1 04dB ref. 70V, F.P. Class of Operation H Product Weight 46 lbs. 44 lbs. 4 1 lbs. Connector: Power 20A line cord 1 5A line cord 1 5A line cord Input Pluggable 3-pin t ...
-
Bogen X600 - page 15
50 Spring Street, Ramsey, NJ 07446, U.S.A. Tel. 20 1 -934-8500; Fax: 20 1 -934-9832; www.bogen.com ...
Bogen X600についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもBogen X600の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBogen X600で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。