Heat Controller BGE-103Aの取扱説明書

32ページ 2.47 mb
ダウンロード

ページに移動 of 32

Summary
  • Heat Controller BGE-103A - page 1

    Through-The-Wall Air Conditioner Service Manual CAUTION -Before servicing the unit, read the "safety precautions" in this manual. -Only for authorized service personnel. HEA T CONTR OLLER, INC. MODELS: BGE-103A BGE-123A ...

  • Heat Controller BGE-103A - page 2

    2 Room Air Conditioner Air Conditioner Ser vice Manual T ABLE OF CONTENTS Safety Precautions .......................................................................................................................................... 3 Installation ....................................................................................................... ...

  • Heat Controller BGE-103A - page 3

    Ser vice Manual 3 Saf ety Precautions Safety Precautions T o prev ent injury to the user or other people and proper ty damage, the f ollowing instructions must be f ollowed. ■ Incorrect operation due to ignoring instruction will cause har m or damage. The seriousness is classified by the f ollowing indications . ■ Meanings of symbols used in th ...

  • Heat Controller BGE-103A - page 4

    4 Room Air Conditioner Saf ety Precautions ■ Operation Do not place heavy object on the power cor d and take care so that the cord should not be pressed. • There is danger of fire or electric shock. Do not share the outlet with other appliances. • It will cause electric shock or fire due to heat generation. T ake the power plug out if neces- ...

  • Heat Controller BGE-103A - page 5

    Ser vice Manual 5 Saf ety Precautions Do not operate or stop the unit by inserting or pulling out the power plug. • It will cause electric shock or fire due to heat generation. Do not damage or use an unspecified power cor d. • It will cause electric shock or fire . Do not operate with wet hands or in damp en vironment. • It will cause electr ...

  • Heat Controller BGE-103A - page 6

    6 Room Air Conditioner Saf ety Precautions Do not put a pet or house plant where it will be exposed to direct air flow . • It ma y cause injur y . Do not bloc k the inlet or outlet of air flo w. • It ma y cause product failure. Use a soft cloth to c lean. Do not use wax, thinner , or a strong detergent. • The appearance of the air condi- tion ...

  • Heat Controller BGE-103A - page 7

    Ser vice Manual 7 Installation Installation Remove packing sheet from the back of the sleeve, and packing corner and blue tape from the air condi- tioner. If you use an existing wall sleeve, you should mea- sure its dimensions. Install the new air conditioner according to these instal- lation instructions to achieve the best performance. All wall s ...

  • Heat Controller BGE-103A - page 8

    • Pick a location which will allow the conditioned air to blow into the area you want. Good installation with special attention to the proper position of the unit will lessen the chance that service will be needed. ITEMS IN INST ALLA TION HARD W ARE You may not need all parts in the kit. Discard unused parts 1. Identify the existing wall sleeve b ...

  • Heat Controller BGE-103A - page 9

    Ser vice Manual 9 Installation Pr ocedure A 1. If you are using the new sleeve (optionally supplied with your unit),skip to step 3. Otherwise, install the plastic grille from the kit. Cut the plastic grille to 25- 1/2" wide and 15-1/4" high. Place the plastic grille to the inside of the wall sleeve at the rear flange. 2. Fasten the 4 wash ...

  • Heat Controller BGE-103A - page 10

    10 Room Air Conditioner Installation Pr ocedure B 1. Redirect the louvers at the back of the wall sleeve to 60 ° angle as shown in the FIG 8. The use of pliers is recommended. 2. If the wall sleeve already has a rear grille, skip to step 4. If the wall sleeve does not have a rear grille or louvered panel, install the plastic grille from the kit. C ...

  • Heat Controller BGE-103A - page 11

    Ser vice Manual 11 Installation 6. Remove the backing from the support blocks and attach them to the inside of the wall sleeve as shown FIG 13. Slide the baffle into slots of the sup- port blocks. 7 . Install the new unit into the wall sleeve. 8 . To assemble trim, snap the tab of each piece into the slot of the other piece as shown below. Slide tr ...

  • Heat Controller BGE-103A - page 12

    12 Room Air Conditioner Installation Pr ocedure C 1. Redirect the louvers at the back of the wall sleeve to 60 ° angle as shown in the FIG 15. The use of pliers is recommended. 2. If the wall sleeve already has a rear grille, skip to step 4. If the wall sleeve does not have a rear grille or louvered panel, install the plastic grille from the kit. ...

  • Heat Controller BGE-103A - page 13

    Ser vice Manual 13 Installation 7. Remove the backing from the 13" shim strips and attach them as shown below in Fig. 22. The higher portion of shim is to be placed in front of the rib on the base of wall sleeve. 8. Install the new unit into the wall sleeve FIG. 21 1" high 3 / 4 " High Shim (2EA) 6" 6" FIG. 22 W all T r im ...

  • Heat Controller BGE-103A - page 14

    14 Room Air Conditioner Operating Instructions Operating Instructions Contr ols The controls will look like one of the following. MODE TIMER PO WER FA N SPEED Fan Heat Energy Saver Cool Timer TEMP ' F F1 LO W F2 HIGH REMOTE CONTROL SIGNAL RECEIVER POWER MODE - Push this button to shift mode of operation from COOL → ENERGY SAVER → FAN → H ...

  • Heat Controller BGE-103A - page 15

    Ser vice Manual 15 Operating Instructions Remote contr ol The remote control and control panel will look like one of the following pictures. Po w e r Te m p F an Speed Timer Mode POWER • To turn the air conditioner ON, push this button. To turn the air conditioner OFF, push the button again. • This button takes priority over any other button. T ...

  • Heat Controller BGE-103A - page 16

    16 Room Air Conditioner Operating Instructions How to insert Batteries 1. Remove the cover from the back of the remote controller. 2. Insert two batteries. • Be sure that the (+) and (-) directions are correct. • Be sure that both batteries are new. 3. Re-attach the cover. • Do not use rechargeable batteries. Such batteries differ from standa ...

  • Heat Controller BGE-103A - page 17

    Ser vice Manual 17 Disassembly Instructions Disassembl y Instructions Mechanical P ar ts — Before the following disassembly, POWER SWITCH is set to OFF and disconnected the power cord. 1. FRONT GRILLE 1. Open the inlet grille upward or downward. 2. Remove the screw which fastens the front grille. 3. Pull the front grille from the right side. 4. R ...

  • Heat Controller BGE-103A - page 18

    18 Room Air Conditioner Disassembly Instructions 4. ORIFICE, HEA TER ASSY AND TURBO F AN 1. Remove the front grille. (Refer to section 1) 2. Remove the cabinet. (Refer to section 2) 3. Remove the 2 screws which fasten the evaporator at the left side and the right side. (See Fig. 27) 4. Move the evaporator sideward carefully. 5. Remove the 2 termina ...

  • Heat Controller BGE-103A - page 19

    Ser vice Manual 19 6. SHROUD 1. Remove the fan. (Refer to section 5) 2. Remove the screw which fasten the shroud. 3. Remove the shroud. (See Fig. 32) 4. Re-install the component by referring to the removal procedure, above. 7. MO T OR 1. Remove the cabinet. (Refer to section 2) 2. Remove the clamp cord and disconnect a wire housing in control box. ...

  • Heat Controller BGE-103A - page 20

    20 Room Air Conditioner Disassembly Instructions 10. PO WER CORD 1. Remove the control box. (Refer to section 3) 2. Unfold the control box. (Refer to section 9) 3. Disconnect the grounding screw from the control box. 4. Disconnect 2 receptacles. 5. Remove a screw which fastens the clip cord. 6. Pull the power cord. (See Fig. 36) 7. Re-install the c ...

  • Heat Controller BGE-103A - page 21

    Ser vice Manual 21 Disassembly Instructions 12. CONDENSER 1. Remove the cabinet. (Refer to section 2) 2. Remove the brace and the shroud cover. (Refer to section 4) 3. Remove the 5 screws which fasten the condenser. 4. After discharging the refrigerant completely, unbraze the interconnecting tube at the condenser connections. 5. Remove the condense ...

  • Heat Controller BGE-103A - page 22

    22 Room Air Conditioner Disassembly Instructions — Replacement of the refrigeration cycle. 1. When replacing the refrigeration cycle, be sure to discharge the refrigerant system using a Freon TM recovery System. If there is no valve to attach the recovery system, install one (such as a WATCO A-1) before venting the Freon TM . Leave the valve in p ...

  • Heat Controller BGE-103A - page 23

    Ser vice Manual 23 Disassembly Instructions Equipment needed: Vacuum pump, Charging cylinder, Manifold gauge, Brazing equipment. Pinch-off tool capa- ble of making a vapor-proof seal, Leak detector, Tubing cutter, Hand Tools to remove components, Service valve. A COMPOUND GAUGE EVAPORATOR (LOW PRESSURE SIDE) COMPRESSOR CAPILLARY TUBE CONDENSER (HIG ...

  • Heat Controller BGE-103A - page 24

    24 Room Air Conditioner Schematic Diagram Schematic Dia gram Wiring Diagram ■ ELECTRIC HEATING MODEL ...

  • Heat Controller BGE-103A - page 25

    Ser vice Manual 25 T roubleshooting Guide T r oubleshooting Guide Piping System Following is a brief description of the important components and their functions in the refrigeration system. Refer to Fig. 41 to follow the refrigeration cycle and the flow of the refrigerant in the cooling cycle. MOTOR COMPRESSOR OIL (LIQUID REFRIGERANT) CAPILLARY TUB ...

  • Heat Controller BGE-103A - page 26

    26 Room Air Conditioner T roubleshooting Guide T r oubleshooting Guide In general, possible trouble is classified in two causes. The one is called Starting Failure which is caused from an electrical defect, and the other is Ineffective Air Conditioning caused by a defect in the refrigeration circuit and improper application. Unit is running but coo ...

  • Heat Controller BGE-103A - page 27

    Ser vice Manual 27 T roubleshooting Guide Fails to Start Check of circuit break er and fuse. Gas leakage of f eeler bulb of ther mostat Check of control s witch. Only f an f ails to star t. Improper wiring. Def ect of f an motor capacitor . Irregular motor resistance ( ). Irregular motor insulation ( ). Replacement of f an motor Regular but f ails ...

  • Heat Controller BGE-103A - page 28

    28 Room Air Conditioner T roubleshooting Guide COMPLAINT CAUSE REMEDY Check voltage at outlet. Correct if none. Check voltage to rotary switch. If none, check power supply cord. Replace cord if circuit is open. Check switch continuity. Refer to wiring diagram for terminal identification. Replace switch if defective. Connect wire. Refer to wiring di ...

  • Heat Controller BGE-103A - page 29

    Ser vice Manual 29 T roubleshooting Guide NAME PLATE RATING MINIMUM MAXIMUM 115V 103.5V 126.5V 208/230V 187V 253V COMPLAINT CAUSE REMEDY Check voltage. See the limits on the preceding. page. If not within limits, call an electrician. Check the wire connections, if loose, repair or replace the terminal. If wires are off, refer to wiring diagram for ...

  • Heat Controller BGE-103A - page 30

    30 Room Air Conditioner COMPLAINT CAUSE REMEDY Check the voltage. See the limits on the preced- ing page. If not within limits, call an electrician. Check overload, if externally mounted. Replace if open. (If the compressor temperature is high, remove the overload, cool, and retest.) If not running, determine the cause. Replace if required. Remove ...

  • Heat Controller BGE-103A - page 31

    Ser vice Manual 31 Product Specifications REMAR K   BGE-103 A    BGE-123 A    REMARK POWER SUPPLY CAPACITY (Btu/h) INPUT (W) RUNNING CURRENT (A) E.E.R. (Btu/W.h) CAPACITY (Btu/h) INPUT (W) RUNNING CURRENT (A) INDOOR (°C) OUTDOOR (°C) INDOOR (°C) OUTDOOR (°C) (inch) (mm) (inch) (mm) (inch) (mm) LOUVERED- FIN TYPE OPTIONA PART 20 510 4 ...

  • Heat Controller BGE-103A - page 32

    Specifications and performance data subject to change without notice. HEA T CONTROLLER, INC. 1900 WELL WOR TH A VENUE • JA CKSON, MICHIGAN 49203 THE QU ALITY LEADER IN CONDITIONING AIR P/No.: 3828A20040 M 04/18/07 ...

メーカー Heat Controller カテゴリー Air Conditioner

Heat Controller BGE-103Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- BGE-103Aの取扱説明書
- Heat Controllerの製品カード
- パンフレット
- またはHeat Controller BGE-103Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Heat Controller BGE-103Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Heat Controller BGE-103Aの取り付け説明書、サービスマニュアル、簡易説明書、またはHeat Controller BGE-103Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Heat Controller BGE-103Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Heat Controller BGE-103Aデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHeat Controller BGE-103Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのHeat Controller BGE-103Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Heat Controllerの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Heat Controller BGE-103Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHeat Controller BGE-103Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Heat Controller BGE-103Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Heat Controller BGE-103Aデバイスの基本機能を使うにあたってのヒント。 Heat Controller BGE-103Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Heat Controller BGE-103Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHeat Controller BGE-103Aのメーカー/サービスへの連絡先に関する情報。

Heat Controller BGE-103Aについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHeat Controller BGE-103Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHeat Controller BGE-103Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)