Chamberlain 1000SDの取扱説明書

36ページ 1.16 mb
ダウンロード

ページに移動 of 36

Summary
  • Chamberlain 1000SD - page 1

    TM The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue Elmhurst, Illinois 60126-1196 For Residential Use Only Garage Door Opener Owner’ s Manual Model 2000SD 1/2 HP Model 1000SD 1/3 HP Complies with UL 325 regulations effective January 1, 1993 ® ■ Please read this manual and the enclosed safety materials car efully! ■ F aste ...

  • Chamberlain 1000SD - page 2

    Start by re viewing these important safety alert symbols: 2 Safety alert symbol re view ............................................2 Safety information and precautions ..............................3 T esting your garage door for binding & balance ..........3 Hardware supplied ........................................................3 Carton in ...

  • Chamberlain 1000SD - page 3

    3 An unbalanced garage door might not rever se when required and someone under the door could be seriously injured or killed. If your garage door binds, sticks or is out of balance, call for prof essional garage door ser vice. Garage doors, door springs, cables, pulleys, brackets, and their hardware are under extreme tension and can cause serious i ...

  • Chamberlain 1000SD - page 4

    4 Straight Door Arm Section Curved Door Arm Section Rail Brackets Header Bracket U P C E IL IN G M O U N T O N L Y Safety Reversing Sensor Mounting Bracket With Square Holes (2) "C" Wrap (2) Safety Reversing Sensor Mounting Bracket With Slot (2) Sprocket Coupling 2-Conductor Bell Wire White & White/Red Remote Control Transmitter (1) w ...

  • Chamberlain 1000SD - page 5

    Y ou may f ind it helpful to refer back to this page as y ou pr oceed with the installation of y our opener . Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 20 for details. Support bracket & fastening hardware is required. ...

  • Chamberlain 1000SD - page 6

    ASSEMBL Y STEP 1 Fasten the Rail T o the P ower Unit 6 Rail Sprocket Rail Assembly Trolley Coupling Rail/Power Unit Bracket Lock Nuts 1/4"-20 Power Unit Sprocket Opener Chassis Foam Packaging Hex Screws 1/4"-20x5/8" ASSEMBL Y STEP 2 Install the T rolley As illustrated abov e, slide the trolley onto and along the bottom of the rail un ...

  • Chamberlain 1000SD - page 7

    ASSEMBL Y STEP 3 Attach the Rail Brac kets 7 IMPOR T ANT INST ALLA TION INSTR UCTIONS T o reduce the risk of se ver e injury or death to persons: 1. READ AND FOLLO W ALL INST ALLA TION INSTR UCTIONS 2. Install only on a properly balanced and lubricated garage door . An improperly balanced door may not reverse and could result in sev ere injury or d ...

  • Chamberlain 1000SD - page 8

    • Open your door to the highest point of trav el as shown. Dra w an inter- secting horizontal line on the header wall 3" abo ve the high point. This height will provide tra vel clearance for the top edge of the door . Header Wall Ceiling Track Highest Point of Travel Door Door Track 3" Header Wall Highest Point of Travel 3" 8 Proce ...

  • Chamberlain 1000SD - page 9

    Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 Header Support OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door . Extend the line onto the header wall abo ve door . If headroom clearance is minimal, you can insta ...

  • Chamberlain 1000SD - page 10

    Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket. UP C E IL IN G M O U N T O N L Y Door Spring Header Bracket 2x4 S ...

  • Chamberlain 1000SD - page 11

    Adjustment Step 4 T est the Safety Rever se System T est • Place a one-inch board (or a 2x4 laid flat) on the floor , centered under the garage door . • Operate the door in the do wn direction. The door must reverse on striking the obstruction. Adjustment If the door stops on the obstruction, it is not trav eling far enough in the do wn directi ...

  • Chamberlain 1000SD - page 12

    The safety re versing sensor must be connected and aligned correctly bef ore the garage door opener will move in the do wn direction. This is a requir ed safety device and cannot be disabled. Installation pr ocedur es ar e the same for sectional and one-piece doors. Be sure po wer to the opener is disconnected. The sending eye transmits an in visib ...

  • Chamberlain 1000SD - page 13

    Adjustment Step 1 Adjust the UP and DO WN Limits Do not make any limit adjustments until the safety re versing sensors are completely installed. 24 Limit adjustment settings regulate the points at which the door will stop when moving up or do wn. The door will stop in the up direction if anything interferes with door trav el. The door will r everse ...

  • Chamberlain 1000SD - page 14

    Door Arm Fully Open Trolley Closed Door Open Door Door with Backward Slant Door Arm Connector Hole Door Arm Connector Hole Fully Closed Trolley Door Arm Nuts 5/16"-18 Lock Washers 5/16" Ring Fastener Straight Arm Screws 5/16"-18x7/8 Door Bracket Clevis Pin 5/16"x1-1/4" Curved Door Arm 14 Figure 6 1/4-20 x 1-1/2" Hex Bo ...

  • Chamberlain 1000SD - page 15

    Installation Step 13 Connect Door Arm to T rolley F ollow instructions which apply to your door type as illustrated below and on page 23. Make sur e garage door is fully closed. Pull the emergency release handle to disconnect the outer tr olley from the inner trolley . Slide the outer trolley back (away fr om the door) about 2" as shown in Fig ...

  • Chamberlain 1000SD - page 16

    Installation Step 6 Hang the Opener T wo repr esentative installations ar e shown. Y ours may be different. Hanging brack ets should be angled, Figure 1, to provide rigid support. On f inished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener . The br acket and fastening har dwar e ar e not suppli ...

  • Chamberlain 1000SD - page 17

    In stallation Step 12 Fasten Door Brac ket F ollow instructions which apply to your door type as illustrated below or on page 21. T o pre vent damage to steel, aluminum, fiberglass or glass panel doors, always reinf orce the inside of the door both vertically and horizontally with an angle ir on. A horizontal brace should be long enough to be secur ...

  • Chamberlain 1000SD - page 18

    T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you ha ve, contact a qualified electrician to install the proper outlet. • If permanent wiring is requir ed by your local code, refe ...

  • Chamberlain 1000SD - page 19

    T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you ha ve, contact a qualified electrician to install the proper outlet. • If permanent wiring is requir ed by your local code, refe ...

  • Chamberlain 1000SD - page 20

    In stallation Step 12 Fasten Door Brac ket F ollow instructions which apply to your door type as illustrated below or on page 21. T o pre vent damage to steel, aluminum, fiberglass or glass panel doors, always reinf orce the inside of the door both vertically and horizontally with an angle ir on. A horizontal brace should be long enough to be secur ...

  • Chamberlain 1000SD - page 21

    Installation Step 6 Hang the Opener T wo repr esentative installations ar e shown. Y ours may be different. Hanging brack ets should be angled, Figure 1, to provide rigid support. On f inished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener . The br acket and fastening har dwar e ar e not suppli ...

  • Chamberlain 1000SD - page 22

    Installation Step 13 Connect Door Arm to T rolley F ollow instructions which apply to your door type as illustrated below and on page 23. Make sur e garage door is fully closed. Pull the emergency release handle to disconnect the outer tr olley from the inner trolley . Slide the outer trolley back (away fr om the door) about 2" as shown in Fig ...

  • Chamberlain 1000SD - page 23

    Door Arm Fully Open Trolley Closed Door Open Door Door with Backward Slant Door Arm Connector Hole Door Arm Connector Hole Fully Closed Trolley Door Arm Nuts 5/16"-18 Lock Washers 5/16" Ring Fastener Straight Arm Screws 5/16"-18x7/8 Door Bracket Clevis Pin 5/16"x1-1/4" Curved Door Arm 14 Figure 6 1/4-20 x 1-1/2" Hex Bo ...

  • Chamberlain 1000SD - page 24

    Adjustment Step 1 Adjust the UP and DO WN Limits Do not make any limit adjustments until the safety re versing sensors are completely installed. 24 Limit adjustment settings regulate the points at which the door will stop when moving up or do wn. The door will stop in the up direction if anything interferes with door trav el. The door will r everse ...

  • Chamberlain 1000SD - page 25

    Adjustment Step 2 Adjust the Force Too much force on the door will interfere with the proper operation of the safety reverse system. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond the minimum amount required to close the door. Do not use the force adjustments t ...

  • Chamberlain 1000SD - page 26

    Adjustment Step 4 T est the Safety Rever se System T est • Place a one-inch board (or a 2x4 laid flat) on the floor , centered under the garage door . • Operate the door in the do wn direction. The door must reverse on striking the obstruction. Adjustment If the door stops on the obstruction, it is not trav eling far enough in the do wn directi ...

  • Chamberlain 1000SD - page 27

    Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket. UP C E IL IN G M O U N T O N L Y Door Spring Header Bracket 2x4 S ...

  • Chamberlain 1000SD - page 28

    Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 Header Support OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door . Extend the line onto the header wall abo ve door . If headroom clearance is minimal, you can insta ...

  • Chamberlain 1000SD - page 29

    Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the door control(s) or remote control transmitter(s). A moving garage door could injure or kill someone under it. Activate the opener only when you can see the door ...

  • Chamberlain 1000SD - page 30

    ASSEMBL Y STEP 3 Attach the Rail Brac kets 7 IMPOR T ANT INST ALLA TION INSTR UCTIONS T o reduce the risk of se ver e injury or death to persons: 1. READ AND FOLLO W ALL INST ALLA TION INSTR UCTIONS 2. Install only on a properly balanced and lubricated garage door . An improperly balanced door may not reverse and could result in sev ere injury or d ...

  • Chamberlain 1000SD - page 31

    ASSEMBL Y STEP 1 Fasten the Rail T o the P ower Unit 6 Rail Sprocket Rail Assembly Trolley Coupling Rail/Power Unit Bracket Lock Nuts 1/4"-20 Power Unit Sprocket Opener Chassis Foam Packaging Hex Screws 1/4"-20x5/8" ASSEMBL Y STEP 2 Install the T rolley As illustrated abov e, slide the trolley onto and along the bottom of the rail un ...

  • Chamberlain 1000SD - page 32

    Y ou may f ind it helpful to refer back to this page as y ou pr oceed with the installation of y our opener . Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 20 for details. Support bracket & fastening hardware is required. ...

  • Chamberlain 1000SD - page 33

    4 Straight Door Arm Section Curved Door Arm Section Rail Brackets Header Bracket U P C E IL IN G M O U N T O N L Y Safety Reversing Sensor Mounting Bracket With Square Holes (2) "C" Wrap (2) Safety Reversing Sensor Mounting Bracket With Slot (2) Sprocket Coupling 2-Conductor Bell Wire White & White/Red Remote Control Transmitter (1) w ...

  • Chamberlain 1000SD - page 34

    3 An unbalanced garage door might not rever se when required and someone under the door could be seriously injured or killed. If your garage door binds, sticks or is out of balance, call for prof essional garage door ser vice. Garage doors, door springs, cables, pulleys, brackets, and their hardware are under extreme tension and can cause serious i ...

  • Chamberlain 1000SD - page 35

    Index Access Door/Outside Quick Release Accessory .........................................................................................................31, 34 Electrical Safety W arnings ......................................................................................................................................7, 18, 27 Garage Door T es ...

  • Chamberlain 1000SD - page 36

    TM The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue Elmhurst, Illinois 60126-1196 For Residential Use Only Garage Door Opener Owner’ s Manual Model 2000SD 1/2 HP Model 1000SD 1/3 HP Complies with UL 325 regulations effective January 1, 1993 ® ■ Please read this manual and the enclosed safety materials car efully! ■ F aste ...

メーカー Chamberlain カテゴリー Garage Door Opener

Chamberlain 1000SDのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 1000SDの取扱説明書
- Chamberlainの製品カード
- パンフレット
- またはChamberlain 1000SDの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Chamberlain 1000SDの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Chamberlain 1000SDの取り付け説明書、サービスマニュアル、簡易説明書、またはChamberlain 1000SDのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Chamberlain 1000SDの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Chamberlain 1000SDデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがChamberlain 1000SDを使用するのを助ける技術的文書のことです。説明書は通常、全てのChamberlain 1000SDユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Chamberlainの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Chamberlain 1000SDの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははChamberlain 1000SDの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Chamberlain 1000SDに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Chamberlain 1000SDデバイスの基本機能を使うにあたってのヒント。 Chamberlain 1000SDのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Chamberlain 1000SDに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるChamberlain 1000SDのメーカー/サービスへの連絡先に関する情報。

Chamberlain 1000SDについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもChamberlain 1000SDの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがChamberlain 1000SDで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)