Z Microsystems 21の取扱説明書

34ページ 1.15 mb
ダウンロード

ページに移動 of 34

Summary
  • Z Microsystems 21 - page 1

    Glider 21 FI ELD-READY User Manu al Z Micr osystems ...

  • Z Microsystems 21 - page 2

    Doc# 27-0017UM Issued 08/03 Rev 1.0 2 FCC INFORMA TION 1. Use the power and video cables supplied with the Glider to help prevent interference with radio and television reception. The use of cables and adapters may cause interfer- ence with electronic equipment in the vicinity of this unit. 2. This equipment has been tested and found to comply with ...

  • Z Microsystems 21 - page 3

    Doc# 27-0017UM Issued 08/03 Rev 1.0 3 TABLE OF CONTENTS ST ARTING POINT 4 Shipment Contents 4 About User Manual 4 System Requirements 4 Features 4 Product Description 5 T ools Required for Installation 6 Precautions 6 INST ALLA TION 7 Slide Removal 7 Install The Slides In Cabinet Frame 8 Installation T est 1 0 Final Adjustments 1 0 Install Cables 1 ...

  • Z Microsystems 21 - page 4

    Doc# 27-0017UM Issued 08/03 Rev 1.0 4 ST ARTING POINT The User Manual comes in two formats: printed hardcopy or CD- ROM. This Manual is also available on the Z Microsystems website (www .zmicro.com). We recommend you read this manual as follows: Carefully follow the instructions in the Installation chapter for hookup and initial control settings. R ...

  • Z Microsystems 21 - page 5

    Doc# 27-0017UM Issued 08/03 Rev 1.0 5 ST ARTING POINT PRODUCT DESCRIPTION The LCD display can quickly swing up into a reading position. The Glider is an advanced space- saving drawer mount high-end rugged liquid crystal display . Specially de- signed quick- release locks hold the compact folded Glider securely in place during storage. The Glider ca ...

  • Z Microsystems 21 - page 6

    Doc# 27-0017UM Issued 08/03 Rev 1.0 6 ST ARTING POINT TOOLS REQUIRED FOR INST ALLA TION PRECAUTIONS Required T ools and Equipment: • Flathead screwdriver with about 10" shaft. • Phillips screwdriver with about 10" shaft. • Adjustable wrench or box wrenches. In preparation to install the Glider , take the following precautionary step ...

  • Z Microsystems 21 - page 7

    Doc# 27-0017UM Issued 08/03 Rev 1.0 7 INST ALLA TION SLIDE REMOVAL With the Glider laid on a workbench, press down to release the Z-Locks on each side of the front of the Glider to slide the side rails back. The slide rails will reach a stop about half way back. This is a safety stop to prevent the Glider from sliding out too far while mounted in t ...

  • Z Microsystems 21 - page 8

    Doc# 27-0017UM Issued 08/03 Rev 1.0 8 INST ALLA TION At the back of the cabinest frame, tighten the slide mounts to the cabinet frame. Make sure to hold the slide mounts hard against the rack rail. On each slide rail, use a Phillips screwdriver to loosen the two adjust- ment screws toward the back of the slide rail. An adjustable wrench or box wren ...

  • Z Microsystems 21 - page 9

    Doc# 27-0017UM Issued 08/03 Rev 1.0 9 INST ALLA TION INST ALL THE GLIDER IN CABINET FRAME The Glider slides should move in and out easily . If not, check alignment of the slider and Z-Lock mount. Pull the two Glider slides out until they lock. Hold the Glider on each side over the back set of rollers, with the front into your stomach. The Glider MU ...

  • Z Microsystems 21 - page 10

    Doc# 27-0017UM Issued 08/03 Rev 1.0 10 INST ALLA TION FINAL ADJUSTMENTS Slide the Glider partially out. Use a flathead screw- driver to slightly move the Z-Locks in toward or out from the Glider , depnding on the need for best fit. While holding the Z-Locks at the proper setting, tighten the screws on the Z- Lock mounts. Go to the rear of the cabin ...

  • Z Microsystems 21 - page 11

    Doc# 27-0017UM Issued 08/03 Rev 1.0 11 INST ALLA TION WARNING: Be sure all electrical power to the cabinet is off before connecting any of the cables. WARNING: There is a key guide for alignment on the cables. Be sure the cable plug and receptacles are aligned properly using the key guide. Misalignment can cause short circuit- ing. INST ALL CABLES ...

  • Z Microsystems 21 - page 12

    Doc# 27-0017UM Issued 08/03 Rev 1.0 12 SETUP VERY IMPORT ANT Hold the top of the display in the vertical position while rotating the latch clockwise to the locked position. Push down on the latch at the base of the display . Then lift the raised latch from its receptical to the unlatched position. Rotate the latch counter- clockwise to unlock the l ...

  • Z Microsystems 21 - page 13

    Doc# 27-0017UM Issued 08/03 Rev 1.0 13 SETUP The display can be rotated clockwise to angled positions. The display can also be moved into the horizon- tal position. The control knobs will be on the bottom. The display can be left in the vertical position or tilted back. SETTING UP GLIDER The Glider can be slid back until the back of the display alm ...

  • Z Microsystems 21 - page 14

    Doc# 27-0017UM Issued 08/03 Rev 1.0 14 PROTECTOR REMOVAL The Protective Outer Shield (optional equipment) is intended to protect the surface of the screen from damage while in transit or while stowed. The display protector is not intended to be used while the display is in operation. T o remove the display protector , do the following: Rotate the d ...

  • Z Microsystems 21 - page 15

    Doc# 27-0017UM Issued 08/03 Rev 1.0 15 OPERA TIONS CABLE CONNECTIONS TURN ON POWER NOTE: Connecting to non- standard systems will require an adapter. T o obtain a video adapter , contact Customer Services at Z Microsystem, Inc. NOTE: Incorrect cable connections may result in irregular operation. Incorrect cable connections may also damage the displ ...

  • Z Microsystems 21 - page 16

    Doc# 27-0017UM Issued 08/03 Rev 1.0 16 OPERA TIONS DISPLA Y PANEL CONTROLS The controller features push-button controls on the lower front of the display screen to adjust the brightness of the display , to change the image positioning on the screen, and to refine the screen image. T o complete the setup of the display , use the following controls t ...

  • Z Microsystems 21 - page 17

    Doc# 27-0017UM Issued 08/03 Rev 1.0 17 OPERA TIONS The three LED lights on the right of the control panel are labeled A , B and C. Their lighted functions are: A — VIDEO A green — VIDEO A is selected B — VIDEO B (green) green — VIDEO B is selected If A & B are both green, it indicates the Channel Auto Switching function is selected. C ? ...

  • Z Microsystems 21 - page 18

    Doc# 27-0017UM Issued 08/03 Rev 1.0 18 OPERA TIONS T o access the onscreen display main menu, press the menu button on the front of the panel. All Glider functions are controlled using the Main Menu’s subtopics. These submenus can be accesssed using the Up and Down buttons on the display panel. See sections below for specifics regarding the subme ...

  • Z Microsystems 21 - page 19

    Doc# 27-0017UM Issued 08/03 Rev 1.0 19 OPERA TIONS This submenu is used to adjust the positioning of the image pixels within the screen. Use the Left and Right buttons to adjust the following modes: Horz Coarse, Horz Fine, H Pos, and V Pos. Main Screen Graphics Mode Use the Up and Down buttons to highlight the “Graphics Mode” option. Press the ...

  • Z Microsystems 21 - page 20

    Doc# 27-0017UM Issued 08/03 Rev 1.0 20 OPERA TIONS Main Screen Information Use the Up and Down buttons to highlight the “Information” option. Press the “Menu” button to access the “Information” submenu. Within this submenu, video mode resolution, the refresh rate, the sync mode, and the firmware version installed on the unit are display ...

  • Z Microsystems 21 - page 21

    Doc# 27-0017UM Issued 08/03 Rev 1.0 21 DISPLA Y HEAD REMOV AL T o remove the Glider display head, follow these steps: On the back of the display , press the mounting arm button to release the display head locking bar . Rotate the display to the horizontal position. On the back of the display , disconnect the power cable. Disconnect the video cable. ...

  • Z Microsystems 21 - page 22

    Doc# 27-0017UM Issued 08/03 Rev 1.0 22 MAINTENANCE CLEAN MONITOR • Gently wipe the covers and the screen with a soft cloth. • Remove finger marks and grease with a damp cloth and mild detergent or alcohol. DO NOT use solvents or abrasives. • Never use flammable cleaning material to clean the monitor or other ectrical apparatus. WARNING: T o a ...

  • Z Microsystems 21 - page 23

    Doc# 27-0017UM Issued 08/03 Rev 1.0 23 DISPLA Y STOWA GE CLOSE GLIDER The following describes closing and stowage of the Glider in the cabinet. Pull the Glider all the way out. Rotate the locking latch clockwise to engage the side lock linkage. ...lower the display into the Glider frame tray . Tilt the display head back towards the rear of the rack ...

  • Z Microsystems 21 - page 24

    Doc# 27-0017UM Issued 08/03 Rev 1.0 24 DISPLA Y STOWA GE Lower the pivot latch into its recepticle. CLOSE GLIDER Slide the Glider into the frame until the Z Locks snap into the closed, secure position. Slide the two display locking bolts at the back of the display to the closed position to secure the display . The display latch has now locked the s ...

  • Z Microsystems 21 - page 25

    Doc# 27-0017UM Issued 08/03 Rev 1.0 25 TROUBLESHOOTING NO IMA GE ON MAIN DISPLA Y If there is no image on the main screen, a signal will appear on the screen that states, “No Input, Check Cable”. If the cable from the computer to the display is secure, determine the color of the standby LED and follow the appropriate procedure below . B LACK Ca ...

  • Z Microsystems 21 - page 26

    Doc# 27-0017UM Issued 08/03 Rev 1.0 26 SPECIFICA TIONS SPECIFICA TIONS Display size 21.3 Inch (432.0 mm x 324.0 mm) Pixels 1600 x 1200 Colors 16.7 Million Contrast Ratio 400:1 Luminescence 250 cd/m 2 (max) Interface 2 Ch. L VDS Response Time Rising 20 msec, Falling 15 msec Backlight 6 CCFL Viewing Angle 80/80 Control Control P anel or SoftMenu Powe ...

  • Z Microsystems 21 - page 27

    Doc# 27-0017UM Issued 08/03 Rev 1.0 27 APPENDIX NOTE: If possible, stay by the computer. The Z Microsystems T echni- cal Support Represen- tative may wish to go through the problem over the telephone. NOTE: More help, late- breaking news and details of the latest accessories for these products may be found on the worldwide web at: http://www .zmicr ...

  • Z Microsystems 21 - page 28

    Doc# 27-0017UM Issued 08/03 Rev 1.0 28 APPENDIX If the Z Microsystems T echnical Support Engineer determines that the product needs to be replaced, a Customer Service Representative will issue a Return Material Authorization (RMA) number and return address. A RMA number is required to return a product to Z Microsystems, regardless of the reason for ...

  • Z Microsystems 21 - page 29

    Doc# 27-0017UM Issued 08/03 Rev 1.0 29 APPENDIX MECHANICAL OUTLINE DRAWINGS ...

  • Z Microsystems 21 - page 30

    Doc# 27-0017UM Issued 08/03 Rev 1.0 30 APPENDIX ...

  • Z Microsystems 21 - page 31

    Doc# 27-0017UM Issued 08/03 Rev 1.0 31 APPENDIX ...

  • Z Microsystems 21 - page 32

    Doc# 27-0017UM Issued 08/03 Rev 1.0 32 APPENDIX ...

  • Z Microsystems 21 - page 33

    Doc# 27-0017UM Issued 08/03 Rev 1.0 33 APPENDIX ...

  • Z Microsystems 21 - page 34

    Z Microsystems, Inc. 5945 Pacific Center Blvd., Suite 505 San Diego, CA 92121 Phone: (858) 657-1000 Fax; (858) 657-1001 W ebsite: www .zmicro.com Copyright 1999 Z Microsystems, Inc. All Rights Reserved ...

メーカー Z Microsystems カテゴリー Computer Monitor

Z Microsystems 21のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 21の取扱説明書
- Z Microsystemsの製品カード
- パンフレット
- またはZ Microsystems 21の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Z Microsystems 21の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Z Microsystems 21の取り付け説明書、サービスマニュアル、簡易説明書、またはZ Microsystems 21のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Z Microsystems 21の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Z Microsystems 21デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがZ Microsystems 21を使用するのを助ける技術的文書のことです。説明書は通常、全てのZ Microsystems 21ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Z Microsystemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Z Microsystems 21の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははZ Microsystems 21の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Z Microsystems 21に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Z Microsystems 21デバイスの基本機能を使うにあたってのヒント。 Z Microsystems 21のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Z Microsystems 21に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるZ Microsystems 21のメーカー/サービスへの連絡先に関する情報。

Z Microsystems 21についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもZ Microsystems 21の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがZ Microsystems 21で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)