-
Interfire A1000.2 - page 1
2 CHANNEL / 4 CHANNEL / 5 CHANNEL AUTOMOTIVE AMPLIFIER INSTRUCTION MANUAL A300.2 / A500.2 / A700.2 A1000.2 / A1100.2 / A2200.2 A500.4 / A700.4 / A900.4 / A800.5 ...
-
Interfire A1000.2 - page 2
1 free installation. • Four Class ''AB'' High-Current Dual Discrete Drive Stages. • Class ''AB'' T echnology MOSFET PWM Power Supply . • Bridgeable & TRI-Mode Operation. • Continuously V ariable 12dB/Octave High Pass & 12dB /Octave Low Pass Crossover. • Subwoofer V ariable Crossover for Deep ...
-
Interfire A1000.2 - page 3
• NEVER operate the amplifier without the proper power and ground wire, 10 gauge minimum. • NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery . This fuse is to protect the car not the electronics. In case of a short, the fuse will blow instead of the wire burning up. Using other t ...
-
Interfire A1000.2 - page 4
1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling. It is very easy to damage the amplifier surface ...
-
Interfire A1000.2 - page 5
It is important to have good quality power and ground connections. Remember , to complete an electrical circuit, the ground connection is just as important as the positive power connection. Before any power connections are made, disconnect the ground cable at the When the power supply lead, memory backup lead or ground lead are extended use a 5mm² ...
-
Interfire A1000.2 - page 6
5 FIG.2 +12V REM GND AUTO - ANTENNA LEAD CH1 CH2 CAR STEREO HEAD UNIT LINE INPUT GAIN BASS L.P.F L.P.F H.P.F H.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz FLAT 80Hz 1.2KHz CROSSOVER CH1 CH2 ...
-
Interfire A1000.2 - page 7
6 CH3 CH4 CH2 CH1 +12V REM GND AUTO - ANTENNA LEAD CAR STEREO HEAD UNIT FIG.2 LINE INPUT LINE INPUT GAIN GAIN BASS BASS CROSSOVER CROSSOVER 6V 0.2V 0dB 12dB 50Hz 500Hz FLAT L.P.F H.P.F FLAT L.P.F H.P.F CH1 CH2 CH3 CH4 50Hz 500Hz 0dB 12dB 6V 0.2V CH 1/2 CH 3/4 ...
-
Interfire A1000.2 - page 8
7 CH3 CH4 CH2 CH1 CH5 CH6 +12V REM GND AUTO - ANTENNA LEAD CAR STEREO HEAD UNIT FIG.2 6V 0.2V FLAT L.P.F 250Hz 50Hz 1.2kHz 80Hz 1.2kHz 80Hz 250Hz 50Hz H.P.F GAIN CH 1/2 LINE INPUT GAIN L.P.F L.P.F H.P.F H.P.F FLAT LINE INPUT CH1 CH2 CH3 CH4 CROSSOVER CROSSOVER 6V 0.2V FLAT 250Hz 50Hz 1.2kHz 80Hz 6V 0.2V CH5 CH6 CH 5 CH 3/4 ...
-
Interfire A1000.2 - page 9
POWER B+ GND REM FUSE SPEAKER CH1 (+) (+) ON PROTECT BRIDGED CH2 POWER B+ GND REM FUSE SPEAKER CH1 (+) (+) ON PROTECT BRIDGED CH2 POWER B+ GND REM FUSE SPEAKER CH1 (+) (+) ON PROTECT BRIDGED CH2 This amplifier can operate in one, two or three channel mode. The minimum impedance for single channel (bridged/mono) operation is 4 or 8 ohms. Tri channel ...
-
Interfire A1000.2 - page 10
CH2 POWER B+ GND REM FUSE SPEAKER (+) (+) (+) (+) CH4 CH3 ON PROTECT CH1 BRIDGED BRIDGED 2 S PEAKER BRIDGED 2 S PEAKER + 1 SUBWOOFER 4 S PEAKER STEREO 6 S PEAKER HEX MODE 9 2-4 Ohms 4 CH 5 CH 4-8 Ohms 6 CH 4-8 Ohms FIG.3 CH2 POWER B+ GND REM FUSE SPEAKER (+) (+) (+) (+) CH4 CH3 ON PROTECT CH1 BRIDGED BRIDGED 3 CH SUB WOOFER 4-8 Ohms 2 CH 1CH 2-4 Oh ...
-
Interfire A1000.2 - page 11
4-8 Ohms 1 CH 2 CH BRIDGED BRIDGED POWER B+ GND REM FUSE SPEAKER (+) CH4 (+) CH5 (+) CH3 ON PROTECT (+) CH1 (+) CH2 BRIDGED BRIDGED POWER B+ GND REM FUSE SPEAKER (+) CH4 (+) CH5 (+) CH3 ON PROTECT (+) CH1 (+) CH2 BRIDGED BRIDGED POWER B+ GND REM FUSE SPEAKER (+) CH4 (+) CH5 (+) CH3 ON PROTECT (+) CH1 (+) CH2 2-8 Ohms 3 C H 3 S PEAKER BRIDGED 10 5 S ...
-
Interfire A1000.2 - page 12
11 1.Set to the "H.P .F" position when the amplifier is used to drive a tweeter/midrange system. The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency 2.Set to the "L.P .F" position when the amplifier is used to dri ...
-
Interfire A1000.2 - page 13
12 ...
-
Interfire A1000.2 - page 14
13 ...
-
Interfire A1000.2 - page 15
14 This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. g. headlights, windows, etc.) Still function correctly . No Audio Low or N.C Remote Turn-on connec ...
-
Interfire A1000.2 - page 16
AMPLIFIER 4 OHMS @ 0.05% THD 4 OHMS Bridged 0.5% THD LOW P ASS FILTE R HIGH PA SS FILT ER MAXIMUM OUTPUT POWER FUSE RAT ING FREQUENCY RESPONSE (-1dB) SIGNAL TO NOISE RAT IO (`A' WTD) INPUT SENSITIVITY INPUT IMPEDANCE OPERATIO N VOLTA GE (NEGAT IVE GROUND) SPEAKER IMPEDANCE @ STEREO DRIVEN DIMENSIONS (W mm x H mm x D mm ) A300.2 75W x 2 150W x ...
-
Interfire A1000.2 - page 17
AMPLIFIER 4 OHMS @ 0.05% THD 4 OHMS Bridged 0.5% THD LOW P ASS FILTE R HIGH PA SS FILT ER MAXIMUM OUTPUT POWER FUSE RAT ING FREQUENCY RESPONSE (-1dB) SIGNAL TO NOISE RAT IO (`A' WTD) INPUT SENSITIVITY INPUT IMPEDANCE OPERATIO N VOLTA GE (NEGATIV E GROUND) SPEAKER IMPEDANCE @ STEREO DRIVEN DIMENSIONS (W mm x H mm x D mm ) 250x59x280 250x59x320 ...
Interfire A1000.2についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもInterfire A1000.2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがInterfire A1000.2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。